Film speed

Not to be confused withframe rate.

"Slow film" redirects here. For the genre of films, seeslow cinema.

Film speedis the measure of aphotographic film'ssensitivity to light,determined bysensitometryand measured onvarious numerical scales,the most recent being theISOsystem introduced in 1974. A closely related system, also known as ISO, is used to describe the relationship between exposure and output imagelightnessin digital cameras. Prior to ISO, the most common systems wereASAin the U.S. andDINin Europe.

This film container denotes its speed as ISO 100/21°, including both arithmetic (100 ASA) and logarithmic (21 DIN) components. The second is often dropped, making (e.g.) "ISO 100" effectively equivalent to the older ASA speed. (As is common, the "100" in the film name alludes to its ISO rating.)

The termspeedcomes from the early days of photography.Photographic emulsionsthat were more sensitive to light needed less time to generate an acceptable image and thus a complete exposure could be finished faster, with the subjects having to hold still for a shorter length of time. Emulsions that were less sensitive were deemed "slower" as the time to complete an exposure was much longer and often usable only forstill life photography.Exposure times for photographic emulsions shortened from hours to fractions of a second by the late 19th century.

In both film and digital photography, the use of higher sensitivities generally leads to reduced image quality (via coarserfilm grainor higherimage noise). Generally, the higher the sensitivity, the grainier the image will be. Ultimately sensitivity is limited by thequantum efficiencyof the film or sensor.

To determine the exposure time needed for a given film, alight meteris typically used.

Film speed measurement systems

Emulsion speed rating criteria

Five criteria for the rating of emulsion speed have been used since the late 19th century, listed here by name and date, these criteria are: threshold (1880), inertia (1890), fixed density (1934), minimum useful gradient (1939) and fractional gradient (1939).

Threshold

The threshold criterion is the point on thecharacteristic curvecorresponding to just perceptible density above fog.

Inertia

The inertia speed point of an emulsion is determined on the Hurter and Driffieldcharacteristic curveby the intercept between the gradient of the straight line part of the curve and the line representing the base + fog (B+F) on the density axis.

Fixed density

The fixed density speed point is determined by defining a fixed minimum density as the basis the emulsion speed (e.g. 0.1 above B+F).

Minimum useful gradient

The minimum useful gradient criterion places the speed point where the gradient first reaches an agreed value (e.g. tan𝜃= 0.2).

Fractional gradient

The fractional gradient is defined as the speed point at which the slope of the characteristic curve first reaches a fixed fraction (e.g. 0.3) of the average gradient over a range (e.g. 1.5) of the characteristic curve.

Historical systems

Warnerke

The first known practicalsensitometer,which allowed measurements of the speed of photographic materials, was invented by the Polish engineerLeon Warnerke– pseudonym ofWładysław Małachowski(1837–1900) – in 1880, among the achievements for which he was awarded theProgress Medalof thePhotographic Society of Great Britainin 1882.It was commercialized since 1881.

The Warnerke Standard Sensitometer consisted of a frame holding an opaque screen with an array of typically 25 numbered, gradually pigmented squares brought into contact with the photographic plate during a timed test exposure under aphosphorescenttablet excited before by the light of a burningmagnesiumribbon.The speed of the emulsion was then expressed in 'degrees' Warnerke (sometimes seen as Warn. or °W.) corresponding with the last number visible on the exposed plate after development and fixation. Each number represented an increase of 1/3 in speed, typical plate speeds were between 10° and 25° Warnerke at the time.

His system saw some success but proved to be unreliabledue to its spectral sensitivity to light, the fading intensity of the light emitted by the phosphorescent tablet after its excitation as well as high built-tolerances.The concept, however, was later built upon in 1900 byHenry Chapman Jones(1855–1932) in the development of his plate tester and modified speed system.

Hurter & Driffield

Another early practical system for measuring the sensitivity of an emulsion was that ofHurter and Driffield(H&D), originally described in 1890, by the Swiss-bornFerdinand Hurter(1844–1898) and BritishVero Charles Driffield(1848–1915). In their system, speed numbers were inversely proportional to the exposure required. For example, an emulsion rated at 250 H&D would require ten times the exposure of an emulsion rated at 2500 H&D.

The methods to determine the sensitivity were later modified in 1925 (in regard to the light source used) and in 1928 (regarding light source, developer and proportional factor)—this later variant was sometimes called "H&D 10". The H&D system was officiallyaccepted as a standard in the formerSoviet Unionfrom 1928 until September 1951, when it was superseded byGOST2817–50.

Scheiner

TheScheinergrade(Sch.) system was devised by the German astronomerJulius Scheiner(1858–1913) in 1894 originally as a method of comparing the speeds of plates used for astronomical photography. Scheiner's system rated the speed of a plate by the least exposure to produce a visible darkening upon development. Speed was expressed in degrees Scheiner, originally ranging from 1° Sch. to 20° Sch., with each increment of a degree corresponding to amultiplicativefactor of increased light sensitivity. This multiplicative factor was determined by the constraint that an increment of 19° Sch. (from 1° Sch. to 20° Sch.) corresponded to a hundredfold increase in sensitivity. Thus emulsions that differed by 1° Sch. on the Scheiner scale were${\sqrt[{19}]{100}}=1.2742...$-fold more (or, less) sensitive to each other. An increment of 3° Sch. came close to a doubling of sensitivity$({\sqrt[{19}]{100}})^{3}=2.06914...$.

The system was later extended to cover larger ranges and some of its practical shortcomings were addressed by the Austrian scientistJosef Maria Eder(1855–1944)and Flemish-born botanistWalter Hecht(1896–1960), (who, in 1919/1920, jointly developed theirEder–Hecht neutral wedge sensitometermeasuring emulsion speeds inEder–Hechtgrades). Still, it remained difficult for manufacturers to reliably determine film speeds, often only by comparing with competing products,so that an increasing number of modified semi-Scheiner-based systems started to spread, which no longer followed Scheiner's original procedures and thereby defeated the idea of comparability.

Scheiner's system was eventually abandoned in Germany, when the standardizedDINsystem was introduced in 1934. In various forms, it continued to be in widespread use in other countries for some time.

DIN

The DIN system, officially DIN standard 4512 by theDeutsches Institut für Normung(then known as theDeutscher Normenausschuß(DNA)), was published in January 1934. It grew out of drafts for a standardized method of sensitometry put forward by theDeutscher Normenausschuß für Phototechnikas proposed by the committee for sensitometry of theDeutsche Gesellschaft für photographische Forschungsince 1930and presented byRobert Luther(1868–1945) andEmanuel Goldberg(1881–1970) at the influential VIII.International Congress of Photography(German:Internationaler Kongreß für wissenschaftliche und angewandte Photographie) held inDresdenfrom 3 to 8 August 1931.

The DIN system was inspired byScheiner's system,but the sensitivities were represented as the base 10 logarithm of the sensitivity multiplied by 10, similar todecibels.Thus an increase of 20° (and not 19° as in Scheiner's system) represented a hundredfold increase in sensitivity, and a difference of 3° was much closer to the base 10 logarithm of 2 (0.30103...):

$\log _{10}{(2)}=0.30103...\approx 3/10$

A box ofAgfacolor Neuwith the instruction "expose as 15/10° DIN" (in German).

As in the Scheiner system, speeds were expressed in 'degrees'. Originally the sensitivity was written as a fraction with 'tenths' (for example "18/10° DIN" ),where the resultant value 1.8 represented the relative base 10 logarithm of the speed. 'Tenths' were later abandoned with DIN 4512:1957-11, and the example above would be written as "18° DIN".The degree symbol was finally dropped with DIN 4512:1961-10. This revision also saw significant changes in the definition of film speeds in order to accommodate then-recent changes in the AmericanASAPH2.5-1960 standard, so that film speeds of black-and-white negative film effectively would become doubled, that is, a film previously marked as "18° DIN" would now be labeled as "21 DIN" without emulsion changes.

Originally only meant for black-and-white negative film, the system was later extended and regrouped into nine parts, including DIN 4512-1:1971-04 for black-and-white negative film, DIN 4512-4:1977-06 for color reversal film and DIN 4512-5:1977-10 for color negative film.

On an international level the German DIN 4512 system has been effectively superseded in the 1980s by ISO 6:1974,ISO 2240:1982,and ISO 5800:1979where the same sensitivity is written in linear and logarithmic form as "ISO 100/21°" (now again with degree symbol). TheseISOstandards were subsequently adopted by DIN as well. Finally, the latest DIN 4512 revisions were replaced by corresponding ISO standards, DIN 4512-1:1993-05 by DIN ISO 6:1996-02 in September 2000, DIN 4512-4:1985-08 by DIN ISO 2240:1998-06 and DIN 4512-5:1990-11 by DIN ISO 5800:1998-06 both in July 2002.

BSI

WhenBS935:1941 was published duringWorld War II,specifying exposure tables for negative materials, it employed the samefixed-densityspeed criterion used in the GermanDIN4512:1934 system. The British Standard also usedlogarithmicspeed numbers, following the example ofScheinerandDIN.When the AmericanASAZ38.2.1:1943 standard was published, it used afractional gradientspeed criterion andarithmeticspeed numbers, for compatibility withWestonandGE.

British standardBS1380:1947 adopted thefractional gradientcriterion of the American 1943 standard, and also includedarithmeticspeed numbers in addition tologarithmicnumbers.Thelogarithmicspeed number proposed in the laterBS1380:1957 standard was almost identical to theDIN4512:1957 standard, except that the BS number was +9 degrees greater than the corresponding DIN number; in 1971, the BS and DIN standards changed this to +10 degrees.

Following an increasing effort to produce international standards, the British, American and German standards became identical inISO6:1974, which corresponded to BS 1380:Part1:1973.

Weston

Weston Model 650light meterfrom about 1935

Early Weston Master light meter 1935-1945

Before the advent of the ASA system, the system ofWeston film speed ratingswas introduced byEdward Faraday Weston(1878–1971) and his father Dr.Edward Weston(1850–1936), a British-born electrical engineer, industrialist and founder of the US-basedWeston Electrical Instrument Corporation,with the Weston model 617, one of the earliest photo-electric exposure meters, in August 1932. The meter and film rating system were invented byWilliam Nelson Goodwin, Jr.,who worked for themand later received aHoward N. Potts Medalfor his contributions to engineering.

The company tested and frequently published speed ratings for most films of the time. Weston film speed ratings could since be found on most Weston exposure meters and were sometimes referred to by film manufacturers and third partiesin their exposure guidelines. Since manufacturers were sometimes creative about film speeds, the company went as far as to warn users about unauthorized uses of their film ratings in their "Weston film ratings" booklets.

The Weston Cadet (model 852 introduced in 1949), Direct Reading (model 853 introduced 1954) and Master III (models 737 and S141.3 introduced in 1956) were the first in their line of exposure meters to switch and utilize the meanwhile establishedASAscale instead. Other models used the original Weston scale up until ca. 1955. The company continued to publish Weston film ratings after 1955,but while their recommended values often differed slightly from the ASA film speeds found on film boxes, these newer Weston values were based on the ASA system and had to be converted for use with older Weston meters by subtracting 1/3 exposure stop as per Weston's recommendation.Vice versa, "old" Weston film speed ratings could be converted into "new" Westons and the ASA scale by adding the same amount, that is, a film rating of 100 Weston (up to 1955) corresponded with 125 ASA (as per ASA PH2.5-1954 and before). This conversion was not necessary on Weston meters manufactured and Weston film ratings published since 1956 due to their inherent use of the ASA system; however the changes of the ASA PH2.5-1960 revision may be taken into account when comparing with newer ASA or ISO values.

General Electric

Prior to the establishment of the ASA scaleand similar toWeston film speed ratingsanother manufacturer of photo-electric exposure meters,General Electric,developed its own rating system of so-calledGeneral Electric film values(often abbreviated asG-EorGE) around 1937.

Film speed values for use with their meters were published in regularly updatedGeneral Electric Film Valuesleaflets and in theGeneral Electric Photo Data Book.

General Electric switched to use theASAscale in 1946. Meters manufactured since February 1946 are equipped with the ASA scale (labeled "Exposure Index" ) already. For some of the older meters with scales in "Film Speed" or "Film Value" (e.g. models DW-48, DW-49 as well as early DW-58 and GW-68 variants), replaceable hoods with ASA scales were available from the manufacturer.The company continued to publish recommended film values after that date, however, they were then aligned to the ASA scale.

ASA

Based on earlier research work byLoyd Ancile Jones(1884–1954) ofKodakand inspired by the systems ofWeston film speed ratingsandGeneral Electric film values,theAmerican Standards Association(now namedANSI) defined a new method to determine and specify film speeds of black-and-white negative films in 1943. ASA Z38.2.1–1943 was revised in 1946 and 1947 before the standard grew into ASA PH2.5-1954. Originally, ASA values were frequently referred to asAmerican standard speed numbersorASA exposure-index numbers.(See also:Exposure Index(EI).)

The ASA scale is a linear scale, that is, a film denoted as having a film speed of 200 ASA is twice as fast as a film with 100 ASA.

The ASA standard underwent a major revision in 1960 with ASA PH2.5-1960, when the method to determine film speed was refined and previously applied safety factors against under-exposure were abandoned, effectively doubling the nominal speed of many black-and-white negative films. For example, anIlford HP3that had been rated at 200 ASA before 1960 was labeled 400 ASA afterwards without any change to the emulsion. Similar changes were applied to theDINsystem with DIN 4512:1961-10 and the BS system with BS 1380:1963 in the following years.

In addition to the established arithmetic speed scale, ASA PH2.5-1960 also introduced logarithmic ASA grades (100 ASA = 5° ASA), where a difference of 1° ASA represented a full exposure stop and therefore the doubling of a film speed. For some while, ASA grades were also printed on film boxes, and they saw life in the form of theAPEXspeed valueS_v(without degree symbol) as well.

ASA PH2.5-1960 was revised as ANSI PH2.5-1979, without the logarithmic speeds, and later replaced by NAPM IT2.5–1986 of the National Association of Photographic Manufacturers, which represented the US adoption of the international standard ISO 6. The latest issue of ANSI/NAPM IT2.5 was published in 1993.

The standard for color negative film was introduced as ASA PH2.27-1965 and saw a string of revisions in 1971, 1976, 1979 and 1981, before it finally became ANSI IT2.27–1988 prior to its withdrawal.

Color reversal film speeds were defined in ANSI PH2.21-1983, which was revised in 1989 before it became ANSI/NAPM IT2.21 in 1994, the US adoption of the ISO 2240 standard.

On an international level, the ASA system was superseded by theISOfilm speed system between 1982 and 1987, however, the arithmetic ASA speed scale continued to live on as the linear speed value of the ISO system.

GOST

A box ofSvemafilm, with a sensitivity of 65GOST(ГОСТ)

GOST(Cyrillic:ГОСТ) was an arithmetic film speed scale defined in GOST 2817-45 and GOST 2817–50.It was used in the formerSoviet Unionsince October 1951,replacingHurter & Driffield(H&D, Cyrillic: ХиД) numbers,which had been used since 1928.

GOST 2817-50 was similar to theASAstandard, having been based on a speed point at a density 0.2 above base plus fog, as opposed to the ASA's 0.1.GOST markings are only found on pre-1987 photographic equipment (film, cameras,lightmeters,etc.) of Soviet Union manufacture.

On 1 January 1987, the GOST scale was realigned to theISOscale with GOST 10691–84,

This evolved into multiple parts including GOST 10691.6–88and GOST 10691.5–88,which both became functional on 1 January 1991.

Current system: ISO

TheASAandDINfilm speed standards have been combined into the ISO standards since 1974.

The currentInternational Standardfor measuring the speed ofcolor negative filmisISO5800:2001(first published in 1979, revised in November 1987) from theInternational Organization for Standardization(ISO). Related standards ISO 6:1993(first published in 1974) and ISO 2240:2003(first published in July 1982, revised in September 1994 and corrected in October 2003) define scales for speeds of black-and-white negative film and color reversal film, respectively.

The determination of ISO speedswith digital still-camerasis described in ISO 12232:2019 (first published in August 1998, revised in April 2006, corrected in October 2006 and again revised in February 2019).

The ISO system defines both anarithmeticand alogarithmic scale.The arithmetic ISO scale corresponds to the arithmetic ASA system, where a doubling of film sensitivity is represented by a doubling of the numerical film speed value. In the logarithmic ISO scale, which corresponds to the DIN scale, adding 3° to the numerical value constitutes a doubling of sensitivity. For example, a film rated ISO 200/24° is twice as sensitive as one rated ISO 100/21°.

Commonly, the logarithmic speed is omitted; for example, "ISO 100" denotes "ISO 100/21°",while logarithmic ISO speeds are written as "ISO 21°" as per the standard.

Conversion between current scales

AYashicaFR with both ASA and DIN markings

Conversion from arithmetic speedSto logarithmic speedS° is given by

$S^{\circ }=10\log S+1$

and rounding to the nearest integer; the log is base 10. Conversion from logarithmic speed to arithmetic speed is given by

$S=10^{\left({S^{\circ }-1}\right)/10}$

and rounding to the nearest standard arithmetic speed in Table 1 below.

Table 1. Comparison of various film speed scales

APEXSv(1960–)	ISO(1974–) arith./log.°	Camera mfrs. (2009–)	ASA(1960–1987) arith.	DIN(1961–2002) log.	GOST(1951–1986) arith.	Example of film stock with this nominal speed
−2	0.8/0°		0.8	0		FPP BW Super Positive
	1/1°		1	1	(1)	Svema Micrat-orto, Astrum Micrat-orto
	1.2/2°		1.2	2	(1)
−1	1.6/3°		1.6	3	1.4
	2/4°		2	4	(2)
	2.5/5°		2.5	5	(2)
0	3/6°		3	6	2.8	Svema MZ-3, Astrum MZ-3
	4/7°		4	7	(4)
	5/8°		5	8	(4)	original three-stripTechnicolor
1	6/9°		6	9	5.5	originalKodachrome
	8/10°		8	10	(8)	Polaroid PolaBlue
	10/11°		10	11	(8)	Kodachrome 8 mm film
2	12/12°		12	12	11	Gevacolor 8 mm reversal film, later Agfa Dia-Direct
	16/13°		16	13	(16)	Agfacolor 8 mm reversal film
	20/14°		20	14	(16)	Adox CMS 20
3	25/15°		25	15	22	old Agfacolor, Kodachrome II and (later)Kodachrome 25,Efke 25
	32/16°		32	16	(32)	Kodak Panatomic-X
	40/17°		40	17	(32)	Kodachrome 40 (movie)
4	50/18°		50	18	45	Fuji RVP (Velvia), Ilford Pan F Plus, Kodak Vision2 50D 5201 (movie), AGFA CT18, Efke 50, Polaroid type 55
	64/19°		64	19	(65)	Kodachrome 64,Ektachrome-X, Polaroid type 64T
	80/20°		80	20	(65)	Ilford Commercial Ortho, Polaroid type 669
5	100/21°		100	21	90	Kodacolor Gold,Kodak T-MAX100 (TMX), KodakEktar,Fujichrome Provia 100F,Efke 100, Fomapan/Arista 100
	125/22°		125	22	(130)	Ilford FP4+,Kodak Plus-X Pan, Svema Color 125
	160/23°		160	23	(130)	Fujicolor Pro 160C/S,Kodak High-Speed Ektachrome,Kodak Portra160NC and 160VC
6	200/24°		200	24	180	Kodak Gold 200,Fujicolor Superia200,Agfa Scala 200x,Fomapan/Arista 200, Wittner Chrome 200D/Agfa Aviphot Chrome 200 PE1
	250/25°		250	25	(250)	Tasma Foto-250, Eastman Double-X
	320/26°		320	26	(250)	Kodak Tri-X Pan Professional (TXP)
7	400/27°		400	27	350	Kodak T-Max 400 (TMY),Kodak Tri-X 400,Kodak Portra400,Ilford HP5+,Fujifilm Superia X-tra 400,Fujichrome Provia 400X,Fomapan/Arista 400
	500/28°		500	28	(500)	Kodak Vision3 500T 5219 (movie)
	640/29°		640	29	(500)	Polaroid 600
8	800/30°		800	30	700	Fuji Pro 800Z,Fuji Instax
	1000/31°		1000	31	(1000)	Ilford Delta3200,Kodak P3200 TMAX Kodak Professional T-Max P3200(seeMarketing anomaliesbelow)
	1250/32°		1250	32	(1000)	Kodak Royal-X Panchromatic
9	1600/33°		1600	33	1400 (1440)	Fujicolor 1600,Fuji Natura 1600 and Superia 1600,Neopan 1600
	2000/34°		2000	34	(2000)
	2500/35°		2500	35	(2000)
10	3200/36°		3200	36	2800 (2880)	Konica 3200, Polaroid type 667, Fujifilm FP-3000B, Kodak Tmax 3200 B&W^
	4000/37°			37	(4000)
	5000/38°			38	(4000)
11	6400/39°		6400	39	5600
	8000/40°
	10000/41°
12	12500/42°	12800	12500			ISO speeds greater than 10000 have not been defined officially before ISO 12232:2019.
	16000/43°
	20000/44°					Polaroid type 612
13	25000/45°	25600
	32000/46°
	40000/47°
14	50000/48°	51200
	64000/49°
	80000/50°
15	100000/51°	102400		51		Nikon D3sandCanon EOS-1D Mark IV(2009)
	125000/52°
	160000/53°
16	200000/54°	204800				Canon EOS-1D X(2011),Nikon D4(2012),Pentax 645Z(2014)
	250000/55°
	320000/56°
17	400000/57°	409600				Nikon D4s,Sony α ILCE-7S(2014),Canon EOS 1D X Mark II(2016)
	500000/58°
	640000/59°
18	800000/60°
	1000000/61°
	1250000/62°
19	1600000/63°
	2000000/64°
	2500000/65°
20	3200000/66°	3280000				Nikon D5(2016)
	4000000/67°	4560000				Canon ME20F-SH(2015)
21		104857600				Photonis INocturn(2021)

Table notes:

1. Speeds shown in bold under APEX, ISO and ASA are values actually assigned in speed standards from the respective agencies; other values are calculated extensions to assigned speeds using the same progressions as for the assigned speeds.
2. APEXS_vvalues 1 to 10 correspond with logarithmic ASA grades 1° to 10° found in ASA PH2.5-1960.
3. ASA arithmetic speeds from 4 to 5 are taken from ANSI PH2.21-1979 (Table 1, p. 8).
4. ASA arithmetic speeds from 6 to 3200 are taken from ANSI PH2.5-1979 (Table 1, p. 5) and ANSI PH2.27-1979.
5. ISO arithmetic speeds from 4 to 3200 are taken from ISO 5800:1987 (Table "ISO speed scales", p. 4).
6. ISO arithmetic speeds from 6 to 10000 are taken from ISO 12232:1998 (Table 1, p. 9).
7. ISO 12232:1998 does not specify speeds greater than 10000. However, the upper limit forS_noise10000 was given as 12500, suggesting that ISO may have envisioned a progression of 12500, 25000, 50000, and 100000, similar to that from 1250 to 10000. This was consistent with ASA PH2.12-1961.For digital cameras, Nikon, Canon, Sony, Pentax, and Fujifilm chose to express the greater speeds in an exact power-of-2 progression from the highest previously realized speed (6400) rather than rounding to an extension of the existing progression. Speed ratings greater than 10000 have finally been defined in ISO 12232:2019.
8. Most of the modern35 mm filmSLRs support an automatic film speed range from ISO 25/15° to 5000/38° withDX-coded films,or ISO 6/9° to 6400/39° manually (without utilizingexposure compensation). The film speed range with support forTTL flashis smaller, typically ISO 12/12° to 3200/36° or less.
9. The Boosteraccessory for theCanon Pellix QL(1965) andCanon FT QL(1966) supported film speeds from 25 to 12800 ASA.
10. The film speed dial of theCanon A-1(1978) supported a speed range from 6 to 12800 ASA (but already called ISO film speeds in the manual).On this camera exposure compensation and extreme film speeds were mutually exclusive.
11. TheLeica R8(1996) andR9(2002) officially supported film speeds of 8000/40°, 10000/41° and 12800/42° (in the case of the R8) or 12500/42° (in the case of the R9), and utilizing its ±3 EV exposure compensation the range could be extended from ISO 0.8/0° to ISO 100000/51° in half exposure steps.
12. Digital camera manufacturers' arithmetic speeds from 12800 to 409600 are from specifications by Nikon (12800, 25600, 51200, 102400 in 2009,204800 in 2012,409600 in 2014), Canon (12800, 25600, 51200, 102400 in 2009,204800 in 2011,4000000 in 2015), Sony (12800 in 2009,25600 in 2010,409600 in 2014), Pentax (12800, 25600, 51200 in 2010,102400, 204800 in 2014) and Fujifilm (12800 in 2011).

Historic ASA and DIN conversion

Historic film speed conversion table, 1952

Classic cameraTessinawith exposure guide, late 1950s

As discussed in theASAandDINsections, the definition of the ASA and DIN scales changed several times in the 1950s up into the early 1960s making it necessary to convert between the different scales. Since theISOsystem combines the newer ASA and DIN definitions, this conversion is also necessary when comparing older ASA and DIN scales with the ISO scale.

The picture shows an ASA/DIN conversion in a 1952 photography bookin which 21/10° DIN was converted to ASA 80 instead of ASA 100.

Some classic camera's exposure guides show the old conversion as they were valid at the time of production, for example the exposure guide of the classic cameraTessina(since 1957), where 21/10° DIN is related to ASA 80, 18° DIN to ASA 40, etc. Users of classic cameras may become confused if they are not aware of the historic background of changing standards.

Determining film speed

ISO 6:1993 method of determining speed for black-and-white film.

Recording film 1000 ASA, Red Light District, Amsterdam, Graffiti 1996

Film speed is found from a plot ofoptical densityvs. log of exposure for the film, known as theD–logHcurve orHurter–Driffieldcurve. There typically are five regions in the curve: the base + fog, the toe, the linear region, the shoulder, and the overexposed region. Forblack-and-whitenegative film,the "speed point" m is the point on the curve where density exceeds the base + fog density by 0.1 when the negative is developed so that a point n where the log of exposure is 1.3 units greater than the exposure at point m has a density 0.8 greater than the density at point m. The exposureH_m,inlux-s,is that for point m when the specified contrast condition is satisfied. The ISO arithmetic speed is determined from:

$S={\frac {0.8\;{\text{lx⋅s}}}{H_{\mathrm {m} }}}$

This value is then rounded to the nearest standard speed in Table 1 of ISO 6:1993.

Determining speed for color negative film is similar in concept but more complex because it involves separate curves for blue, green, and red. The film is processed according to the film manufacturer's recommendations rather than to a specified contrast. ISO speed forcolor reversal filmis determined from the middle rather than the threshold of the curve; it again involves separate curves for blue, green, and red, and the film is processed according to the film manufacturer's recommendations.

Applying film speed

Film speed is used in theexposure equationsto find the appropriate exposure parameters. Four variables are available to the photographer to obtain the desired effect:lighting,film speed,f-number(aperture size), andshutter speed(exposure time). The equation may be expressed as ratios, or, by taking the logarithm (base 2) of both sides, by addition, using the APEX system, in which every increment of 1 is a doubling of exposure; this increment is commonly known as a "stop". Theeffective f-numberis proportional to the ratio between the lensfocal lengthandaperturediameter, the diameter itself being proportional to the square root of the aperture area. Thus, a lens set tof/1.4allows twice as much light to strike the focal plane as a lens set tof/2. Therefore, each f-number factor of the square root of two (approximately 1.4) is also a stop, so lenses are typically marked in that progression:f/1.4, 2, 2.8, 4, 5.6, 8, 11, 16, 22, 32, etc.

The ISO arithmetic speed has a useful property for photographers without the equipment for taking a metered light reading. Correct exposure will usually be achieved for a frontlighted scene in bright sun if the aperture of the lens is set to f/16 and the shutter speed is the reciprocal of the ISO film speed (e.g. 1/100 second for 100 ISO film). This known as thesunny 16 rule.

Exposure index

Exposure index, or EI, refers to speed rating assigned to a particular film and shooting situation in variance to the film's actual speed. It is used to compensate for equipment calibration inaccuracies or process variables, or to achieve certain effects. The exposure index may simply be called thespeed setting,as compared to the speedrating.

For example, a photographer may rate an ISO 400 film at EI 800 and then usepush processingto obtain printable negatives in low-light conditions. The film has been exposed at EI 800.

Another example occurs where a camera'sshutteris miscalibrated and consistently overexposes or underexposes the film; similarly, alight metermay be inaccurate. One may adjust the EI setting accordingly in order to compensate for these defects and consistently produce correctly exposed negatives.

Reciprocity

Upon exposure, the amount of light energy that reaches the film determines the effect upon the emulsion. If the brightness of the light is multiplied by a factor and the exposure of the film decreased by the same factor by varying the camera'sshutter speedand aperture, so that the energy received is the same, the film will be developed to the same density. This rule is calledreciprocity.The systems for determining the sensitivity for an emulsion are possible because reciprocity holds over a wide range of customary conditions. In practice, reciprocity works reasonably well for normal photographic films for the range of exposures between 1/1000 second to 1/2 second. However, this relationship breaks down outside these limits, a phenomenon known asreciprocity failure.

Film sensitivity and grain

Main article:Film grain

Grainy high-speed B&W film negative

The size ofsilver halidegrains in theemulsionaffects film sensitivity, which is related togranularitybecause larger grains give film greater sensitivity to light. Fine-grain film, such as film designed for portraiture or copyingoriginal camera negatives,is relatively insensitive, or "slow", because it requires brighter light or a longer exposure than a "fast" film. Fast films, used for photographing in low light or capturing high-speed motion, produce comparatively grainy images.

Kodakhas defined a "Print Grain Index" (PGI) to characterize film grain (color negative films only), based on perceptualjust-noticeable differenceof graininess in prints. They also define "granularity", a measurement of grain using an RMS measurement of density fluctuations in uniformly exposed film, measured with a microdensitometer with 48 micrometre aperture.Granularity varies with exposure — underexposed film looks grainier than overexposed film.

Marketing anomalies

Some high-speed black-and-white films, such asIlford Delta3200,P3200 T-Max,and T-MAX P3200 are marketed with film speeds in excess of their true ISO speed as determined using the ISO testing method. According to the respective data sheets, the Ilford product is actually an ISO 1000 film,while the Kodak film's speed is nominally 800 to 1000 ISO.The manufacturers do not indicate that the 3200 number is an ISO rating on their packaging.Kodak and Fuji also marketed E6 films designed for pushing (hence the "P" prefix), such as Ektachrome P800/1600 and Fujichrome P1600, both with a base speed of ISO 400. TheDX codeson the film cartridges indicate the marketed film speed (i.e. 3200), not the ISO speed, in order to automate shooting and development.

Digital camera ISO speed and exposure index

ACCDimage sensor, 2/3 inch size

Indigital camera systems,an arbitrary relationship between exposure and sensor data values can be achieved by setting thesignal gainof the sensor. The relationship between the sensor data values and the lightness of the finished image is also arbitrary, depending on the parameters chosen for the interpretation of the sensor data into an imagecolor spacesuch assRGB.

For digital photo cameras ( "digital still cameras" ), anexposure index(EI) rating—commonly calledISOsetting—is specified by the manufacturer such that the sRGB image files produced by the camera will have a lightness similar to what would be obtained with film of the same EI rating at the same exposure. The usual design is that the camera's parameters for interpreting the sensor data values into sRGB values are fixed, and a number of different EI choices are accommodated by varying the sensor's signal gain in the analog realm, prior to conversion to digital. Some camera designs provide at least some EI choices by adjusting the sensor's signal gain in the digital realm ( "expanded ISO" ). A few camera designs also provide EI adjustment through a choice of lightness parameters for the interpretation of sensor data values into sRGB; this variation allows different tradeoffs between the range of highlights that can be captured and the amount of noise introduced into the shadow areas of the photo.

Digital cameras have far surpassed film in terms of sensitivity to light, withISOequivalent speeds of up to 4,560,000, a number that is unfathomable in the realm of conventional film photography. Fastermicroprocessors,as well as advances in software noise reduction techniques allow this type of processing to be executed the moment the photo is captured, allowing photographers to store images that have a higher level of refinement and would have been prohibitively time-consuming to process with earlier generations of digital camera hardware.

The ISO (International Organization of Standards) 12232:2019 standard

The ISO standard ISO 12232:2006gave digital still camera manufacturers a choice of five different techniques for determining the exposure index rating at each sensitivity setting provided by a particular camera model. Three of the techniques in ISO 12232:2006 were carried over from the 1998 version of the standard, while two new techniques allowing for measurement of JPEG output files were introduced fromCIPADC-004.Depending on the technique selected, the exposure index rating could depend on the sensor sensitivity, the sensor noise, and the appearance of the resulting image. The standard specified the measurement of light sensitivity of the entire digital camera system and not of individual components such as digital sensors, although Kodak has reportedusing a variation to characterize the sensitivity of two of their sensors in 2001.

TheRecommended Exposure Index(REI) technique, new in the 2006 version of the standard, allows the manufacturer to specify a camera model'sEIchoices arbitrarily. The choices are based solely on the manufacturer's opinion of what EI values produce well-exposedsRGBimages at the various sensor sensitivity settings. This is the only technique available under the standard for output formats that are not in the sRGB color space. This is also the only technique available under the standard whenmulti-zone metering(also calledpatternmetering) is used.

TheStandard Output Sensitivity(SOS) technique, also new in the 2006 version of the standard, effectively specifies that the average level in the sRGB image must be 18% gray plus or minus 1/3 stop when the exposure is controlled by an automatic exposure control system calibrated perISO 2721and set to the EI with noexposure compensation.Because the output level is measured in the sRGB output from the camera, it is only applicable to sRGBimages—typicallyJPEG—and not to output files inraw image format.It is not applicable when multi-zone metering is used.

The CIPA DC-004 standard requires that Japanese manufacturers of digital still cameras use either the REI or SOS techniques, and DC-008updates theExifspecification to differentiate between these values. Consequently, the three EI techniques carried over from ISO 12232:1998 are not widely used in recent camera models (approximately 2007 and later). As those earlier techniques did not allow for measurement from images produced withlossy compression,they cannot be used at all on cameras that produce images only in JPEG format.

Thesaturation-based(SAT or S_sat) technique is closely related to the SOS technique, with the sRGB output level being measured at 100% white rather than 18% gray. The SOS value is effectively 0.704 times the saturation-based value.Because the output level is measured in thesRGBoutput from the camera, it is only applicable to sRGB images—typicallyTIFF—and not to output files in raw image format.It is not applicable when multi-zone metering is used.

The twonoise-basedtechniques have rarely been used for consumer digital still cameras.These techniques specify the highest EI that can be used while still providing either an "excellent" picture or a "usable" picture depending on the technique chosen.

An update to this standard has been published as ISO 12232:2019, defining a wider range of ISO speeds.

Measurements and calculations

ISO speed ratings of a digital camera are based on the properties of the sensor and the image processing done in the camera, and are expressed in terms of the luminous exposureH(inluxseconds) arriving at the sensor. For a typical camera lens with an effectivefocal lengthfthat is much smaller than the distance between the camera and the photographed scene,His given by

$H={\frac {qLt}{N^{2}}},$

whereLis theluminanceof the scene (incandelaperm²),tis the exposure time (in seconds),Nis the aperture f-number, and

$q={\frac {\pi }{4}}T\,v(\theta )\,\cos ^{4}\theta$

is a factor depending on thetransmittanceTof the lens, thevignettingfactorv(θ), and the angleθrelative to the axis of the lens. A typical value isq= 0.65, based onθ= 10°,T= 0.9, andv= 0.98.

Saturation-based speed

Thesaturation-based speedis defined as

$S_{\mathrm {sat} }={\frac {78\;{\text{lx⋅s}}}{H_{\mathrm {sat} }}},$

where$H_{\mathrm {sat} }$is the maximum possible exposure that does not lead to a clipped or bloomed camera output. Typically, the lower limit of the saturation speed is determined by the sensor itself, but with thegainof the amplifier between the sensor and theanalog-to-digital converter,the saturation speed can be increased. The factor 78 is chosen such that exposure settings based on a standardlight meterand an 18-percent reflective surface will result in an image with a grey level of 18%/√2= 12.7% of saturation. The factor√2indicates that there is half a stop of headroom to deal withspecular reflectionsthat would appear brighter than a 100% reflecting diffuse white surface.

Noise-based speed

Main article:Signal to noise ratio (imaging)

Digital noise at 3200 ISO vs. 100 ISO

Thenoise-based speedis defined as the exposure that will lead to a givensignal-to-noise ratioon individualpixels.Two ratios are used, the 40:1 ( "excellent image quality" ) and the 10:1 ( "acceptable image quality" ) ratio. These ratios have been subjectively determined based on a resolution of 70 pixels per cm (178 DPI) when viewed at 25 cm (9.8 inch) distance. The noise is defined as thestandard deviationof a weighted average of theluminanceand color of individual pixels. The noise-based speed is mostly determined by the properties of the sensor and somewhat affected by the noise in the electronic gain and AD converter.

Standard output sensitivity (SOS)

In addition to the above speed ratings, the standard also defines thestandard output sensitivity(SOS), how the exposure is related to the digital pixel values in the output image. It is defined as

$S_{\mathrm {sos} }={\frac {10\;{\text{lx⋅s}}}{H_{\mathrm {sos} }}},$

where$H_{\mathrm {sos} }$is the exposure that will lead to values of 118 in 8-bit pixels, which is 18 percent of the saturation value in images encoded assRGBor withgamma= 2.2.

Discussion

The standard specifies how speed ratings should be reported by the camera. If the noise-based speed (40:1) ishigherthan the saturation-based speed, the noise-based speed should be reported, roundeddownwardsto a standard value (e.g. 200, 250, 320, or 400). The rationale is that exposure according to the lower saturation-based speed would not result in a visibly better image. In addition, an exposure latitude can be specified, ranging from the saturation-based speed to the 10:1 noise-based speed. If the noise-based speed (40:1) islowerthan the saturation-based speed, or undefined because of high noise, the saturation-based speed is specified, rounded upwards to a standard value, because using the noise-based speed would lead to overexposed images. The camera may also report the SOS-based speed (explicitly as being an SOS speed), rounded to the nearest standard speed rating.

For example, a camera sensor may have the following properties:$S_{40:1}=107$,$S_{10:1}=1688$,and$S_{\mathrm {sat} }=49$.According to the standard, the camera should report its sensitivity as

ISO 100 (daylight)

ISO speed latitude 50–1600

ISO 100 (SOS, daylight).

The SOS rating could be user controlled. For a different camera with a noisier sensor, the properties might be$S_{40:1}=40$,$S_{10:1}=800$,and$S_{\mathrm {sat} }=200$.In this case, the camera should report

ISO 200 (daylight),

as well as a user-adjustable SOS value. In all cases, the camera should indicate for the white balance setting for which the speed rating applies, such as daylight or tungsten (incandescent light).

Despite these detailed standard definitions, cameras typically do not clearly indicate whether the user "ISO" setting refers to the noise-based speed, saturation-based speed, or the specified output sensitivity, or even some made-up number for marketing purposes. Because the 1998 version of ISO 12232 did not permit measurement of camera output that had lossy compression, it was not possible to correctly apply any of those measurements to cameras that did not producesRGBfiles in an uncompressed format such asTIFF.Following the publication of CIPA DC-004 in 2006, Japanese manufacturers of digital still cameras are required to specify whether a sensitivity rating is REI or SOS.

A greater SOS setting for a given sensor comes with some loss of image quality, just like with analog film. However, this loss is visible as image noise rather thangrain.APS- and 35 mm-sized digitalimage sensors,both CMOS and CCD based, do not produce significant noise until aboutISO 1600.

See also

• Frame rate
• Lens speed
• Preferred number

Further reading

• ISO 6:1974,ISO 6:1993(1993-02).Photography — Black-and-white pictorial still camera negative film/process systems — Determination of ISO speed.Geneva: International Organization for Standardization.
• ISO 2240:1982(1982-07),ISO 2240:1994(1994-09),ISO 2240:2003(2003–10).Photography — Colour reversal camera films — Determination of ISO speed.Geneva: International Organization for Standardization.
• ISO 2720:1974.General Purpose Photographic Exposure Meters (Photoelectric Type) — Guide to Product Specification.Geneva: International Organization for Standardization.
• ISO 5800:1979,ISO 5800:1987(1987-11),ISO 5800:1987/Cor 1:2001(2001-06).Photography — Colour negative films for still photography — Determination of ISO speed.Geneva: International Organization for Standardization.
• ISO 12232:1998(1998-08),ISO 12232:2006(2006-04-15), ISO 12232:2006 (2006-10-01),ISO 12232:2019(2019-02-01).Photography — Digital still cameras — Determination of exposure index, ISO speed ratings, standard output sensitivity, and recommended exposure index.Geneva: International Organization for Standardization.
• ASA Z38.2.1-1943, ASA Z38.2.1-1946, ASA Z38.2.1-1947 (1947-07-15).American Standard Method for Determining Photographic Speed and Speed Number.New York: American Standards Association. Superseded by ASA PH2.5-1954.
• ASA PH2.5-1954, ASA PH2.5-1960.American Standard Method for Determining Speed of photographic Negative Materials (Monochrome, Continuous Tone).New York: United States of America Standards Institute (USASI). Superseded by ANSI PH2.5-1972.
• ANSI PH2.5-1972, ANSI PH2.5-1979 (1979-01-01), ANSI PH2.5-1979(R1986).Speed of photographic negative materials (monochrome, continuous tone, method for determining).New York: American National Standards Institute. Superseded by NAPM IT2.5-1986.
• NAPM IT2.5-1986,ANSI/ISO 6-1993 ANSI/NAPM IT2.5-1993(1993-01-01).Photography — Black-and-White Pictorial Still Camera Negative Film/Process Systems — Determination of ISO Speed (same as ANSI/ISO 6-1993).National Association of Photographic Manufacturers. This represents the US adoption of ISO 6.
• ASA PH2.12-1957, ASA PH2.12-1961.American Standard, General-Purpose Photographic Exposure Meters (photoelectric type).New York: American Standards Association. Superseded by ANSI PH3.49-1971.
• ANSI PH2.21-1983 (1983-09-23), ANSI PH2.21-1983(R1989).Photography (Sensitometry) Color reversal camera films – Determination of ISO speed.New York: American Standards Association. Superseded by ANSI/ISO 2240-1994 ANSI/NAPM IT2.21-1994.
• ANSI/ISO 2240-1994 ANSI/NAPM IT2.21-1994.Photography – Colour reversal camera films – determination of ISO speed.New York: American National Standards Institute. This represents the US adoption of ISO 2240.
• ASA PH2.27-1965 (1965-07-06), ASA PH2.27-1971, ASA PH2.27-1976, ANSI PH2.27-1979, ANSI PH2.27-1981, ANSI PH2.27-1988 (1988-08-04).Photography – Colour negative films for still photography – Determination of ISO speed (withdrawn).New York: American Standards Association. Superseded by ANSI IT2.27-1988.
• ANSI IT2.27-1988 (1994-08/09?).Photography Color negative films for still photography – Determination of ISO speed.New York: American National Standards Institute. Withdrawn. This represented the US adoption of ISO 5800.
• ANSI PH3.49-1971, ANSI PH3.49-1971(R1987).American National Standard for general-purpose photographic exposure meters (photoelectric type).New York: American National Standards Institute. After several revisions, this standard was withdrawn in favor of ANSI/ISO 2720:1974.
• ANSI/ISO 2720:1974, ANSI/ISO 2720:1974(R1994) ANSI/NAPM IT3.302-1994.General Purpose Photographic Exposure Meters (Photoelectric Type) — Guide to Product Specification.New York: American National Standards Institute. This represents the US adoption of ISO 2720.
• BSI BS 1380:1947, BSI BS 1380:1963.Speed and exposure index.British Standards Institution. Superseded by BSI BS 1380-1:1973 (1973-12), BSI BS 1380-2:1984 (1984-09), BSI BS 1380-3:1980 (1980-04) and others.
• BSI BS 1380-1:1973Archived2011-10-09 at theWayback Machine(1973-12-31).Speed of sensitized photographic materials: Negative monochrome material for still and cine photography.British Standards Institution. Replaced by BSI BS ISO 6:1993, superseded by BSI BS ISO 2240:1994.
• BSI BS 1380-2:1984 ISO 2240:1982Archived2011-10-09 at theWayback Machine(1984-09-28).Speed of sensitized photographic materials. Method for determining the speed of colour reversal film for still and amateur cine photography.British Standards Institution. Superseded by BSI BS ISO 2240:1994.
• BSI BS 1380-3:1980 ISO 5800:1979Archived2011-10-09 at theWayback Machine(1980-04-30).Speed of sensitized photographic materials. Colour negative film for still photography.British Standards Institution. Superseded by BSI BS ISO 5800:1987.
• BSI BS ISO 6:1993Archived2011-10-09 at theWayback Machine(1995-03-15).Photography. Black-and-white pictorial still camera negative film/process systems. Determination of ISO speed.British Standards Institution. This represents the British adoption of ISO 6:1993.
• BSI BS ISO 2240:1994Archived2011-10-09 at theWayback Machine(1993-03-15),BSI BS ISO 2240:2003Archived2011-10-09 at theWayback Machine(2004-02-11).Photography. Colour reversal camera films. Determination of ISO speed.British Standards Institution. This represents the British adoption of ISO 2240:2003.
• BSI BS ISO 5800:1987Archived2011-10-09 at theWayback Machine(1995-03-15).Photography. Colour negative films for still photography. Determination of ISO speed.British Standards Institution. This represents the British adoption of ISO 5800:1987.
• DIN 4512:1934-01, DIN 4512:1957-11 (Blatt 1), DIN 4512:1961-10 (Blatt 1).Photographische Sensitometrie, Bestimmung der optischen Dichte.Berlin: Deutscher Normenausschuß (DNA). Superseded by DIN 4512-1:1971-04, DIN 4512-4:1977-06, DIN 4512-5:1977-10 and others.
• DIN 4512-1:1971-04,DIN 4512-1:1993-05.Photographic sensitometry; systems of black and white negative films and their process for pictorial photography; determination of speed.Berlin: Deutsches Institut für Normung (before 1975: Deutscher Normenausschuß (DNA)). Superseded by DIN ISO 6:1996-02.
• DIN 4512-4:1977-06,DIN 4512-4:1985-08.Photographic sensitometry; determination of the speed of colour reversal films.Berlin: Deutsches Institut für Normung. Superseded by DIN ISO 2240:1998-06.
• DIN 4512-5:1977-10,DIN 4512-5:1990-11.Photographic sensitometry; determination of the speed of colour negative films.Berlin: Deutsches Institut für Normung. Superseded by DIN ISO 5800:1998-06.
• DIN ISO 6:1996-02.Photography – Black-and-white pictorial still camera negative film/process systems – Determination of ISO speed (ISO 6:1993).Berlin: Deutsches Institut für Normung. This represents the German adoption of ISO 6:1993.
• DIN ISO 2240:1998-06,DIN ISO 2240:2005-10.Photography – Colour reversal camera films – Determination of ISO speed (ISO 2240:2003).Berlin: Deutsches Institut für Normung. This represents the German adoption of ISO 2240:2003.
• DIN ISO 5800:1998-06,DIN ISO 5800:2003-11.Photography – Colour negative films for still photography – Determination of ISO speed (ISO 5800:1987 + Corr. 1:2001).Berlin: Deutsches Institut für Normung. This represents the German adoption of ISO 5800:2001.
• Leslie B. Stroebel, John Compton, Ira Current, Richard B. Zakia.Basic Photographic Materials and Processes,second edition. Boston: Focal Press, 2000.ISBN0-240-80405-8.

External links

• What is the meaning of ISO for digital cameras?Digital Photography FAQ
• Signal-dependent noise modeling, estimation, and removal for digital imaging sensors

• "Handbook of Photography" by Henney and Dudley (1939)Spreadsheet Comparing Film Speed Systems