M16 mine

TheM16 mineis a United States-madebounding anti-personnel mine.It was based on captured plans of theWorld War IIera GermanS-mineand has similar performance.

M16 mine
A cutaway of an M16A2 mine
Type	Boundinganti-personnel mine
Place of origin	United States
Service history
In service	1957–present
Used by	See description
Wars	Vietnam War,other
Production history
Produced	1950's-1974
No.built	Millions
Variants	M16A1 M16A2 KM16A2
Specifications
Mass	4.1 kg
Height	127 mm
Diameter	102 mm
Filling	TNT
Filling weight	1 LB
Detonation mechanism	Various, including: S.Mi.Z 35 (pressure), Z.Z.35 (pull), Z.U.Z.Z. (tension release), E.S.Mi.Z (pressure and electric)

Description

The mine consists of a cast iron body in a thin steel sleeve. A centralfuzewell on the top of the mine is normally fitted with a pronged M605 pressure/tension (tripwire)fuze.Sufficient pressure on the prongs or tension on an attached tripwire causes the release of a striker. The freed striker is forced into apercussion capwhich ignites a shortpyrotechnic delay.The purpose of this delay is to allow the victim to move off the top of the mine, to prevent its upward movement from being blocked. Once the delay has burned through, a 4.5-gramblack powdercharge is ignited, which launches the inner iron body of the mine up into the air (leaving behind the steel outer sleeve). The charge also ignites a second pair of pyrotechnic delays.

The mine rises to a height of 0.3 to 1.7 metersbefore one or both of the pyrotechnic delaysdetonatesthe main charge of the mine, which sprays high-speed metal fragments 360° around the point of detonation. These metal fragments have an expected casualty radius of 27 meters for the M16 and M16A1 mines, and out to 30 meters for the M16A2 mine.

The M16 and M16A1 mines are similar; the M16A1 has redesigned detonators and boosters but remains largely the same. The M16A2 is considerably different, having an offset fuse well and only a single pyrotechnic delay element. This change reduces the weight of the mine considerably (2.83 kilograms) while allowing it to carry a slightly larger main charge (601 grams)

Use

According to theUnited States Army,oneplatoonofcombat engineersassisted by a hauling vehicle was expected to be able to emplace 300 M-16 mines in 120 minutes, creating a minefield 300 meters long and 50 meters wide with a linear density of one mine per meter of front.

The mines were sold widely and copies were produced in several countries including Greece, India, Myanmar, South Korea and Turkey. They can be found in the 'wild' inAngola,Burma,Cambodia,Chile,Cyprus,Eritrea,Ethiopia,Iran,Iraq,Korea,Lebanon,Laos,Malawi,Mozambique,Myanmar,Oman,Rwanda,Somalia,Thailand,Vietnam,theWestern Sahara,andZambia.The United States retains stocks of M16A2 mines for use in any resumption of war in Korea.

Variants

• M16
• M16A1 – Redesigned detonator and delay elements
• M16A2 – Single bounding delay element, reducing the weight
• KM16A2 – South Korean produced version of the M16A2

Demining

When emplaced, most of an M16 mine is buried underground so it can be extremely difficult to spot them visually, particularly in areas of long grass, heavy undergrowth or other debris. The M16 contains large amounts of metal, so is very easy to detect using a mine detector. However, it is important to note that the act of moving the detection head over the ground may strike the prongs and trigger the mine. In any case, otherminimum metal minesmay have been planted near to an M16 in order to protect it from mine clearance personnel. Additionally, if long tripwires are fitted, the M16 may "see" the deminers before they have chance to find it. When tracking the path of tripwires fitted to any bounding mine, great care must be taken: it is quite possible that additional antipersonnel blast mines (e.g. theM14) may have been buried beneath its path. An extra complicating factor is that some M16 mines may have been fitted with ananti-handling devicee.g. placing anM26 grenadeunderneath it with an M5 pressure-release boobytrap firing device screwed into it.Deliberately triggering the mines from cover, using some form ofgrappling hookattached to a long rope, may be useful in some varied situations and provide an initial way into the minefield before further clearance work begins.

See also

• Valmara 59– (Italy)
• Valmara 69– (Italy)
• PROM-1– (Yugoslavia)
• OZM– (Soviet Union)
• Ottawa Treaty

References

• Jane's Mines and Mines Clearance 2005–2006
• Brassey's Essential Guide to Anti-personnel Landmines,Eddie Banks
• M16atORDATA
• M16A1atORDATA
• M16A2atORDATA