Wikipedia

USB hardware

The initial versions of theUSBstandard specified connectors that were easy to use and that would have acceptable life spans; revisions of the standard added smaller connectors useful for compact portable devices. Higher-speed development of the USB standard gave rise to another family of connectors to permit additional data paths. All versions of USB specify cable properties; version 3.xcables include additional data paths. The USB standard includedpower supplytoperipheraldevices; modern versions of the standard extend the power delivery limits forbattery chargingand devices requiring up to 240watts.USB has been selected as the standard charging format for manymobile phones,reducing the proliferation of proprietary chargers.

Various legacy USB connectors along a centimeter ruler for scale.
  1. Micro-B plug
  2. Proprietary UC-E6 connector used on many older Japanese cameras for both USB and analog AV output
  3. Mini-B plug
  4. Standard-A receptacle (non-compliant because USB does not allow extension cables[1])
  5. Standard-A plug
  6. Standard-B plug

Connectors

edit
Comparison oflegacyUSB connector plugs, omitting the current standard Type-C plugs

Unlike other databuses(such asEthernet), USB connections are directed; a host device has "downstream" facing ports that connect to the "upstream" facing ports of devices. Only downstream facing ports provide power; this topology was chosen to easily prevent electrical overloads and damaged equipment. Thus, USB cables have different ends: A and B, with different physical connectors for each. Each format has a plug and receptacle defined for each of the A and B ends. A USB cable, by definition, has a plug on each end—one A (or C) and one B (or C)—and the corresponding receptacle is usually on a computer or electronic device. The mini and micro formats may connect to an AB receptacle, which accepts either an A or a B plug, that plug determining the behavior of the receptacle.

The three sizes of USB connectors are the default, orstandard,format intended for desktop or portable equipment, theminiintended for mobile equipment, which was deprecated when it was replaced by the thinnermicrosize, all of which were deprecated in USB 3.2 in favor of Type-C. There are five speeds for USB data transfer: Low Speed, Full Speed, High Speed (from version 2.0 of the specification),SuperSpeed(from version 3.0), and SuperSpeed+ (from version 3.1). The modes have differing hardware and cabling requirements. USB devices have some choice of implemented modes, and USB version is not a reliable statement of implemented modes. Modes are identified by their names and icons, and the specification suggests that plugs and receptacles be color-coded (SuperSpeed is identified by blue).

Connector properties

edit
Non-standard USB extension cable, plug on the left, receptacle on the right. (USB does not allow extension cables.[1]Non-standard cables may work but cannot be presumed reliable.)

The connectors the USB committee specifies support a number of USB's underlying goals, and reflect lessons learned from the many connectors the computer industry has used. The connector mounted on the host or device is called thereceptacle,and the connector attached to the cable is called theplug.[2]The official USB specification documents also periodically define the termmaleto represent the plug, andfemaleto represent the receptacle.[3][clarification needed]

By design, it is difficult to insert a USB plug into its receptacle incorrectly. The USB specification requires that the cable plug and receptacle be marked so the user can recognize the proper orientation.[2]The USB-C plug however is reversible. USB cables and small USB devices are held in place by the gripping force from the receptacle, with no screws, clips, or thumb-turns as other connectors use.

The different A and B plugs prevent accidentally connecting two power sources. However, some of this directed topology is lost with the advent of multi-purpose USB connections (such asUSB On-The-Goin smartphones, and USB-powered Wi-Fi routers), which require A-to-A, B-to-B, and sometimes Y/splitter cables. See theUSB On-The-Go connectorssection below for a more detailed summary description.

There are so-calledcableswith A plugs on both ends, which may be valid if the "cable" includes, for example, a USB host-to-host transfer device with two ports.[4]This is, by definition, a device with two logical B ports, each with a captive cable, not a cable with two A ends.

Durability

edit

The standard connectors were designed to be more robust than many past connectors. This is because USB ishot-swappable,and the connectors would be used more frequently, and perhaps with less care, than previous connectors.

Standard USB has a minimum rated lifetime of 1,500 cycles of insertion and removal,[5]the Mini-USB receptacle increased this to 5,000 cycles,[5]and the newer Micro-USB[5]and USB-C receptacles are both designed for a minimum rated lifetime of 10,000 cycles of insertion and removal.[6]To accomplish this, a locking device was added and the leaf-spring was moved from the jack to the plug, so that the most-stressed part is on the cable side of the connection. This change was made so that the connector on the less expensive cable would bear the mostwear.[5][page needed]

In standard USB, the electrical contacts in a USB connector are protected by an adjacent plastic tongue, and the entire connecting assembly is usually protected by an enclosing metal shell.[5]

The shell on the plug makes contact with the receptacle before any of the internal pins. The shell is typically grounded, to dissipate static electricity and to shield the wires within the connector.

Compatibility

edit

The USB standard specifies tolerances for compliant USB connectors to minimize physical incompatibilities in connectors from different vendors. The USB specification also defines limits to the size of a connecting device in the area around its plug, so that adjacent ports are not blocked. Compliant devices must either fit within the size restrictions or support a compliant cable that does.

Pinouts

edit
See also:USB 3.0 § Pinouts

USB 2.0 uses two wires for power (VBUSand GND), and two fordifferential serial data signals.Mini and micro connectors have their GND connections moved from pin #4 to pin #5, while their pin #4 serves as an ID pin for the On-The-Go host/client identification.[7]

USB 3.0 provides two additional differential pairs (four wires, SSTx+, SSTx−, SSRx+ and SSRx−), providingfull-duplexdata transfers atSuperSpeed,which makes it similar toSerial ATAor single-lanePCI Express.

Standard, Mini-, and Micro-USB plugsshown end-on, not to scale. Light areas represent cavities. The plugs are pictured with USB logo to the top.[8]
Micro-B SuperSpeed plug
  1. Power (VBUS,5 V)
  2. Data− (D−)
  3. Data+ (D+)
  4. ID (On-The-Go)
  5. GND
  6. SuperSpeed transmit− (SSTx−)
  7. SuperSpeed transmit+ (SSTx+)
  8. GND
  9. SuperSpeed receive− (SSRx−)
  10. SuperSpeed receive+ (SSRx+)
Type-A and -B pinout
Pin Name Wire color[a] Description
1 VBUS Red or Orange +5 V
2 D− White or Gold Data−
3 D+ Green Data+
4 GND Black or Blue Ground
Mini/Micro-A and -B pinout
Pin Name Wire color[a] Description
1 VBUS Red +5 V
2 D− White Data−
3 D+ Green Data+
4 ID No wire On-The-GoID distinguishes cable ends:
  • "A" plug (host): connected to GND
  • "B" plug (device): not connected
5 GND Black Signal ground
  1. ^abIn some sources D+ and D− are erroneously swapped.

Colors

edit
A yellow charge-only "USB" Type-A receptacle and a USB 3.0 Type-A receptacle, both upside-down, on a front panel with card reader
A blue Standard-A USB receptacle without USB 3.0 contacts fitted
Usual USB color-coding
Color Location Description
Black or white Receptacles and plugs Type-A or Type-B
Blue (Pantone300C) Receptacles and plugs Type-A or Type-B, SuperSpeed
Teal blue Receptacles and plugs Type-A or Type-B, SuperSpeed+
Green Receptacles and plugs Type-A or Type-B,QualcommQuick Charge (QC)
Purple Plugs only Type-A or Type-C,HuaweiSuperCharge
Yellow or red Receptacles only High-current orsleep-and-charge
Orange Receptacles only High-retention connector, mostly used on industrial hardware

USB ports and connectors are often color-coded to distinguish their different functions and USB versions. These colors are not part of the USB specification and can vary between manufacturers; for example, the USB 3.0 specification mandates appropriate color-coding while it only recommends blue inserts for Standard-A USB 3.0 connectors and plugs.[9]

Connector types

edit

USB connector types multiplied as the specification progressed. The original USB specification detailed standard-A and standard-B plugs and receptacles. The connectors were different so that users could not connect one computer receptacle to another. The data pins in the standard plugs are recessed compared to the power pins so that the device can power up before establishing a data connection. Some devices operate in different modes depending on whether the data connection is made. Charging docks supply power and do not include a host device or data pins, allowing any capable USB device to charge or operate from a standard USB cable. Charging cables provide power connections, but not data. In a charge-only cable, the data wires are shorted at the device end, otherwise, the device may reject the charger as unsuitable.

Standard connectors

edit
Pin configuration of Type-A and Type-B plugs viewed end-on
  • The Type-A plug. This plug has an elongated rectangular cross-section, inserts into a Type-A receptacle on adownstream porton a USB host or hub, and carries both power and data. Captive cables on USB devices such as keyboards or mice terminate with a Type-A plug.
  • The Type-B plug: This plug has a near square cross-section with the top exterior corners beveled. As part of a removable cable, it inserts into anupstream porton a device, such as a printer. On some devices, the Type-B receptacle has no data connections, being used solely for accepting power from the upstream device. This two-connector-type scheme (A/B) prevents a user from accidentally creating a loop.[10][11]

The maximum allowed cross-section of theovermold boot(which is part of the connector used for its handling) is 16 by 8 mm (0.63 by 0.31 in) for the Standard-A plug type, while for the Type-B it is 11.5 by 10.5 mm (0.45 by 0.41 in).[3]

Mini connectors

edit
Mini-A (left) and Mini-B (right) plugs

Mini-USB connectors were introduced together with USB 2.0 in April 2000, mostly used with smaller devices such asdigital cameras,smartphones,andtablet computers.The Mini-A connector and the Mini-AB receptacle connector have beendeprecatedsince May 2007.[12]Mini-B connectors are still supported, but are notOn-The-Go-compliant;[13]the Mini-B USB connector was standard for transferring data to and from the early smartphones and PDAs. Both Mini-A and Mini-B plugs are approximately 3 by 7 mm (0.12 by 0.28 in). The Mini-AB receptacle accepts either a Mini-A or Mini-B plug.

Micro connectors

edit
Micro-A
plug
Micro-B
plug

Micro-USB connectors, which were announced by theUSB-IFon January 4, 2007,[14][15]have a similar width to Mini-USB, but approximately half the thickness, enabling their integration into thinner portable devices. The Micro-A connector is 6.85 by 1.8 mm (0.270 by 0.071 in) with a maximum overmold boot size of 11.7 by 8.5 mm (0.46 by 0.33 in), while the Micro-B connector is 6.85 by 1.8 mm (0.270 by 0.071 in) with a maximum overmold size of 10.6 by 8.5 mm (0.42 by 0.33 in).[8]

The thinner Micro-USB connectors were intended to replace the Mini connectors in devices manufactured since May 2007, includingsmartphones,personal digital assistants,and cameras.[16]

The Micro plug design is rated for at least 10,000 connect-disconnect cycles, which is more than the Mini plug design.[14][17]The Micro connector is also designed to reduce the mechanical wear on the device; instead, the easier-to-replace cable is designed to bear the mechanical wear of connection and disconnection. TheUniversal Serial Bus Micro-USB Cables and Connectors Specificationdetails the mechanical characteristics of Micro-Aplugs,Micro-AB receptacles (which accept both Micro-A and Micro-B plugs), Double-Sided Micro USB, and Micro-B plugs and receptacles,[17]along with a Standard-A receptacle to a Micro-A plug adapter.

OMTP standard
edit

Micro-USB was endorsed as the standard connector for data and power on mobile devices by the cellular phone carrier groupOpen Mobile Terminal Platform(OMTP) in 2007.[18]

Micro-USB was embraced as the "Universal Charging Solution" by theInternational Telecommunication Union(ITU) in October 2009.[19]

In Europe, micro-USB became the definedcommon external power supply(EPS) for use with smartphones sold in the EU,[20]and 14 of the world's largest mobile phone manufacturers signed the EU's common EPS Memorandum of Understanding (MoU).[21][22]Apple,one of the original MoU signers, makes Micro-USB adapters available—as permitted in the Common EPS MoU—for itsiPhonesequipped with Apple's proprietary30-pin dock connectoror (later)Lightning connector.[23][24]according to theCEN,CENELEC,andETSI.

USB 3.xconnectors and backward compatibility

edit
USB 3.0 Micro-B SuperSpeed plug
See also:USB 3.0 § Connectors

USB 3.0 introduced Type-A SuperSpeed plugs and receptacles as well as micro-sized Type-B SuperSpeed plugs and receptacles. The 3.0 receptacles are backward-compatible with the corresponding pre-3.0 plugs.

USB 3.xand USB 1.xType-A plugs and receptacles are designed to interoperate. To achieve USB 3.0's SuperSpeed (and SuperSpeed+ for USB 3.1 Gen 2), 5 extra pins are added to the unused area of the original 4 pin USB 1.0 design, making USB 3.0 Type-A plugs and receptacles backward compatible to those of USB 1.0.

On the device side, a modified Micro-B plug (Micro-B SuperSpeed) is used to cater for the five additional pins required to achieve the USB 3.0 features (USB-C plug can also be used). The USB 3.0 Micro-B plug effectively consists of a standard USB 2.0 Micro-B cable plug, with an additional 5 pins plug "stacked" to the side of it. In this way, cables with smaller 5 pin USB 2.0 Micro-B plugs can be plugged into devices with 10 contact USB 3.0 Micro-B receptacles and achieve backward compatibility.

USB cables exist with various combinations of plugs on each end of the cable, as displayed below in theUSB cables matrix.

USB 3.0 Standard-B plug

USB On-The-Go connectors

edit
Main article:USB On-The-Go

USB On-The-Go(OTG) introduces the concept of a device performing both host and device roles. All current OTG devices are required to have one, and only one, USB connector: a Micro-AB receptacle. (In the past, before the development of Micro-USB, On-The-Go devices usedMini-AB receptacles.)

The Micro-AB receptacle is capable of accepting Micro-A and Micro-B plugs, attached to any of the legal cables and adapters as defined in revision 1.01 of the Micro-USB specification.

To enable Type-AB receptacles to distinguish which end of a cable is plugged in, plugs have an "ID" pin in addition to the four contacts in standard-size USB connectors. This ID pin is connected to GND in Type-A plugs, and left unconnected in Type-B plugs. Typically, apull-up resistorin the device is used to detect the presence or absence of an ID connection.

The OTG device with the A-plug inserted is called the A-device and is responsible for powering the USB interface when required, and by default assumes the role of host. The OTG device with the B-plug inserted is called the B-device and by default assumes the role of peripheral. An OTG device with no plug inserted defaults to acting as a B-device. If an application on the B-device requires the role of host, then the Host Negotiation Protocol (HNP) is used to temporarily transfer the host role to the B-device.

OTG devices attached either to a peripheral-only B-device or a standard/embedded host have their role fixed by the cable, since in these scenarios it is only possible to attach the cable one way.[citation needed]

USB-C

edit
Main article:USB-C
TheUSB-Cplug
USB cable with a USB-C plug and a USB-C port on a notebook computer

The USB-C connector supersedes all earlier USB connectors and the Mini DisplayPort connector. It is used for all USB protocols and for Thunderbolt (3 and later), DisplayPort (1.2 and later), and others. Developed at roughly the same time as the USB 3.1 specification, but distinct from it, the USB-C Specification 1.0 was finalized in August 2014[25]and defines a new small reversible-plug connector for USB devices.[26]The USB-C plug connects to both hosts and devices, replacing various Type-A and Type-B connectors and cables with a standard meant to befuture-proof.[25][27]

The 24-pin double-sided connector provides four power–ground pairs, two differential pairs for USB 2.0 data (though only one pair is implemented in a USB-C cable), four pairs for SuperSpeed data bus (only two pairs are used in USB 3.1 mode), two "sideband use" pins, VCONN+5 V power for active cables, and a configuration pin for cable orientation detection and dedicatedbiphase mark code(BMC) configuration data channel (CC).[28][29]Type-A and Type-B adaptors and cables are required for older hosts and devices to plug into USB-C hosts and devices. Adapters and cables with a USB-C receptacle are not allowed.[30]

Full-featured USB-C 3.1 cables contain a full set of wires and are "electronically marked" (E-marked): they contain a "eMarker" chip that responds to theUSB Power DeliveryDiscover Identitycommand, a kind of vendor-defined message (VDM) sent over the configuration data channel (CC). Using this command, the cable reports its current capacities, maximum speed, and other parameters.[31]: §4.9 Full-Featured USB Type-C devices are a mechanic prerequisite for multi-lane operation (USB 3.2 Gen 1x2, USB 3.2 Gen 2x2, USB4 2x2, USB4 3x2, USB Gen 4 Asymmetric).[31]

USB-C devices support power currents of 1.5 A and 3.0 A over the 5 V power bus in addition to baseline 900 mA. These higher currents can be negotiated through the configuration line. Devices can also utilize the full Power Delivery specification using both BMC-coded configuration line and legacyBFSK-coded VBUSline.[31]: §4.6.2.1 

Host and device interface receptacles

edit

USB plugs fit one receptacle with notable exceptions for USB On-The-Go "AB" support and the general backward compatibility of USB 3.0 as shown.

USB connector mating table (images not to scale)
Plug
Receptacle
 USB A
 USB 3.0 A SS
 USB B
 USB 3.0 B SS
 USB Mini-A
 USB Mini-B
 USB Micro-A1
 USB Micro-B
 USB 3.0 Micro-B
 USB-C
USB A
 Yes Only non-
SuperSpeed 		No No No No No No No No
USB 3.0 A SS
 Only non-
SuperSpeed 		Yes No No No No No No No No
USB B
 No No Yes No No No No No No No
USB 3.0 B SS
 No No Only non-
SuperSpeed 		Yes No No No No No No
USB Mini-A
 No No No No Yes No No No No No
USB Mini-AB
 No No No No Deprecated Deprecated No No No No
USB Mini-B
 No No No No No Yes No No No No
USB Micro-AB
 No No No No No No Yes Yes No No
USB Micro-B
 No No No No No No No Yes No No
USB 3.0 Micro-B SS
 No No No No No No No Only non-
SuperSpeed 		Yes No
USB-C
 No No No No No No No No No Yes
^1No corresponding Micro-A receptacle was ever designed.
USB cables table
Plugs, each end USB A
 USB Mini-A
 USB Micro-A
 USB B
 USB Mini-B
 USB Micro-B
 USB 3.0 Micro-B
 USB-C
USB A
 Proprietary,
hazardous[1] 		Proprietary,
hazardous[1] 		Proprietary,
hazardous[1] 		Yes Yes Yes Yes Yes
USB Mini-A
 Proprietary,
hazardous[1] 		No No Deprecated Deprecated Non-
standard 		No No
USB Micro-A
 Proprietary,
hazardous[1] 		No No Non-
standard 		Non-
standard 		Yes No No
USB B
 Yes Deprecated Non-
standard 		No No No No Yes
USB Mini-B
 Yes Deprecated Non-
standard 		No OTG non-
standard 		OTG non-
standard 		No Yes
USB Micro-B
 Yes Non-
standard 		Yes No OTG non-
standard 		OTG non-
standard 		No Yes
USB 3.0 Micro-B
 Yes No No No No No OTG non-
standard 		Yes
USB-C
 Yes No No Yes Yes Yes Yes Yes
Proprietary, hazardous
Existing for specificproprietary purposes,not inter-operable with USB-IF compliant equipment and possibly damaging to both devices when plugged in. In addition to the above cable assemblies comprising two plugs, an "adapter" cable with a Micro-A plug and a standard-A receptacle is compliant with USB specifications.[8]Other combinations of connectors are not compliant.
There do exist A-to-A assemblies, referred to as cables (such as theEasy Transfer Cable); however, these have a pair of USB devices in the middle, making them more than just cables.
Non-standard
The USB standards do not exhaustively list all combinations with one Type-A and one Type-B connector, however, most such cables have good chances of working.
OTG non-standard
Commonly available "OTG" cables that address widespread misuse of Micro-B and Mini-B receptacles for OTG devices, e.g. smartphones (as opposed to Micro-AB and Mini-AB, which accept either plug.) While not compliant with the USB standards, these cables at least do not provide a device damage hazard since Type-B ports on devices are unpowered by default.[32]
Deprecated
Some older devices and cables with Mini-A connectors have been certified by USB-IF. The Mini-A connector is obsolete: no new Mini-A connectors and neither Mini-A nor Mini-AB receptacles will be certified.[12]
Note: Mini-B is not deprecated, although it is less and less used since the arrival of Micro-B. Micro-A and Micro-B have one more contact than Standard-A and Standard-B in order for hardware with a Micro-AB receptacle to discern Micro-A from Micro-B and behave as a host or device accordingly.

Proprietary connectors and formats

edit

Manufacturers of personal electronic devices might not include a USB standard connector on their product for technical or marketing reasons.[33]E.g. Olympus has been using a special cable called CB-USB8 one end of which has a special contact. Some manufacturers provide proprietary cables, such asLightning,that permit their devices to physically connect to a USB standard port. Full functionality of proprietary ports and cables with USB standard ports is not assured; for example, some devices only use the USB connection for battery charging and do not implement any data transfer functions.[34]

Cabling

edit
A USB twisted pair, in which theData+andData−conductors are twisted together in a doublehelix.The wires are enclosed in a further layer of shielding.

The D± signals used by low, full, and high speed are carried over atwisted pair(typically unshielded) to reducenoiseandcrosstalk.SuperSpeed uses separate transmit and receivedifferential pairs,which additionally require shielding (typically, shielded twisted pair buttwinaxis also mentioned by the specification). Thus, to support SuperSpeed data transmission, cables contain twice as many wires and are larger in diameter.[35]

The USB 1.1 standard specifies that a standard cable can have a maximum length of 5 metres (16 ft 5 in) with devices operating at full speed (12 Mbit/s), and a maximum length of 3 metres (9 ft 10 in) with devices operating at low speed (1.5 Mbit/s).[36][37][38]

USB 2.0 provides for a maximum cable length of 5 metres (16 ft 5 in) for devices running at high speed (480 Mbit/s). The primary reason for this limit is the maximum allowed round-trip delay of about 1.5 μs. If USB host commands are unanswered by the USB device within the allowed time, the host considers the command lost. When adding USB device response time, delays from the maximum number of hubs added to the delays from connecting cables, the maximum acceptable delay per cable amounts to 26 ns.[38]The USB 2.0 specification requires that cable delay be less than5.2 ns/m(1.6 ns/ft,192000km/s), which is close to the maximum achievable transmission speed for standard copper wire.

The USB 3.0 standard does not directly specify a maximum cable length, requiring only that all cables meet an electrical specification: for copper cabling withAWG26 wires the maximum practical length is 3 metres (9 ft 10 in).[39]

Power

edit
See also:USB hub § Power

Downstream USB connectors supply power at a nominal5 V DCvia the V_BUS pin to upstream USB devices.

Voltage tolerance and limits

edit
Worst-case voltage drop topology of a USB 2.0 host to low-power device chain, at steady state

The tolerance on V_BUS at an upstream (or host) connector was originally ±5% (i.e. could lie anywhere in the range 4.75 V to 5.25 V). With the release of theUSB Type-Cspecification in 2014 and its 3 A power capability, theUSB-IFelected to increase the upper voltage limit to 5.5 V to combatvoltage droopat higher currents.[40]The USB 2.0 specification (and therefore implicitly also the USB 3.xspecifications) was also updated to reflect this change at that time.[41]A number of extensions to the USB Specifications have progressively further increased the maximum allowable V_BUS voltage: starting with 6.0 V with USB BC 1.2,[42]to 21.5 V with USB PD 2.0[43]and 50.9 V with USB PD 3.1,[43]while still maintaining backwards compatibility with USB 2.0 by requiring various forms ofhandshakebefore increasing the nominal voltage above 5 V.

USB PD continues the use of the bilateral 5% tolerance, with allowable voltages ofPDO±5% ±0.5 V (eg. for a PDO of 9.0 V, the maximum and minimum limits are 9.95 V and 8.05 V, respectively).[43]

There are several minimum allowable voltages defined at different locations within a chain of connectors, hubs, and cables between an upstream host (providing the power) and a downstream device (consuming the power). To allow for voltage drops, the voltage at the host port, hub port, and device are specified to be at least 4.75 V, 4.4 V, and 4.35 V respectively by USB 2.0 for low-power devices,[a]but must be at least 4.75 V at all locations for high-power[b]devices (however, high-power devices are required to operate as a low-powered device so that they may be detected and enumerated if connected to a low-power upstream port). The USB 3.xspecifications require that all devices must operate down to 4.00 V at the device port.

Unlike USB 2.0 and USB 3.2, USB4 does not define its own VBUS-based power model. Power for USB4 operation is established and managed as defined in the USB Type-C Specification and the USB PD Specification.

  1. ^Low-power devices are those which draw less than 1 unit load. 1 unit load is 100 mA for USB 2.0
  2. ^High-power devices in USB 2.0 are those that draw more than one unit load (up to a maximum of 5 unit loads). 1 unit load is 100 mA.
Worst-case voltage drop topology of a USB 3.xhost to device chain, at steady state. Note that under transient conditions the supply at the device can momentarily drop from 4.0 V to 3.67 V.

Allowable current draw

edit
USB power standards
Specification Current Voltage Power (max.)
Low-power device 100 mA 5 V 0.50 W
Low-power SuperSpeed (USB 3.0) device 150 mA 5 V 0.75 W
High-power device 500 mA[a] 5 V 2.5 W
High-power SuperSpeed (USB 3.0) device 900 mA[b] 5 V 4.5 W
Battery Charging (BC) 1.2 1.5 A 5 V 7.5 W
Single-lane SuperSpeed+ (USB 3.2 Gen2x1, and former USB 3.1 Gen2) device 1.5 A[c] 5 V 7.5 W
Power Delivery 3.0 SPR 3 A 5 V 15 W
Power Delivery 3.0 SPR 3 A 9 V 27 W
Power Delivery 3.0 SPR 3 A 15 V 45 W
Power Delivery 3.0 SPR 3 A 20 V 60 W
Power Delivery 3.0 SPR Type-C 5 A[d] 20 V 100 W
Power Delivery 3.1 EPR Type-C 5 A[d] 28 V[e] 140 W
Power Delivery 3.1 EPR Type-C 5 A[d] 36 V[e] 180 W
Power Delivery 3.1 EPR Type-C 5 A[d] 48 V[e] 240 W
  1. ^Up to 5 unit loads; with non-SuperSpeed devices, one unit load is 100 mA.
  2. ^Up to 6 unit loads; with SuperSpeed devices, one unit load is 150 mA.
  3. ^Up to 6 unit loads; with multi-lane devices, one unit load is 250 mA.
  4. ^abcd>3 A (>20 W) operation requires an electronically marked cable rated at 5 A.
  5. ^abc>20 V (>60 W) operation requires an electronically marked Extended Power Range (EPR) cable.

The limit to device power draw is stated in terms of aunit loadwhich is 100 mA for USB 2.0, or 150 mA for SuperSpeed (i.e. USB 3.x) devices. Low-power devices may draw at most 1 unit load, and all devices must act as low-power devices before they are configured. A high-powered device must be configured, after which it may draw up to 5 unit loads (500 mA), or 6 unit loads (900 mA) for SuperSpeed devices, as specified in its configuration because the maximum power may not always be available from the upstream port.[44][45][46][47]

A bus-powered hub is a high-power device providing low-power ports. It draws 1 unit load for the hub controller and 1 unit load for each of at most 4 ports. The hub may also have some non-removable functions in place of ports. A self-powered hub is a device that provides high-power ports by supplementing the power supply from the host with its own external supply. Optionally, the hub controller may draw power for its operation as a low-power device, but all high-power ports must draw from the hub's self-power.

Where devices (for example, high-speed disk drives) require more power than a high-power device can draw,[48]they function erratically, if at all, from bus power of a single port. USB provides for these devices as being self-powered. However, such devices may come with a Y-shaped cable that has two USB plugs (one for power and data, the other for only power), so as to draw power as two devices.[49]Such a cable is non-standard, with the USB compliance specification stating that "use of a 'Y' cable (a cable with two A-plugs) is prohibited on any USB peripheral", meaning that "if a USB peripheral requires more power than allowed by the USB specification to which it is designed, then it must be self-powered."[50]

USB battery charging

edit

USB Battery Charging(BC) defines acharging port,which may be acharging downstream port(CDP), with data, or adedicated charging port(DCP) without data. Dedicated charging ports can be found on USB power adapters to run attached devices and battery packs. Charging ports on a host with both kinds will be labeled.[51]

The charging device identifies a charging port by non-data signaling on the D+ and D− terminals. A dedicated charging port places a resistance not exceeding 200 Ω across the D+ and D− terminals.[51]: §1.4.7; table 5-3 

Per the base specification, any device attached to astandard downstream port(SDP) must initially be a low-power device, with high-power mode contingent on later USB configuration by the host. Charging ports, however, can immediately supply between 0.5 and 1.5 A of current. The charging port must not apply current limiting below 0.5 A, and must not shut down below 1.5 A or before the voltage drops to 2 V.[51]

Since these currents are larger than in the original standard, the extra voltage drop in the cable reduces noise margins, causing problems with High Speed signaling. Battery Charging Specification 1.1 specifies that charging devices must dynamically limit bus power current draw during High Speed signaling;[52]1.2 specifies that charging devices and ports must be designed to tolerate the higher ground voltage difference in High Speed signaling.

Revision 1.2 of the specification was released in 2010. It made several changes, and increased limits including allowing 1.5 A on charging downstream ports for unconfigured devices—allowing High Speed communication while having a current up to 1.5 A. Also, support was removed for charging port detection via resistive mechanisms.[53]

Before the Battery Charging Specification was defined, there was no standardized way for the portable device to inquire how much current was available. For example, Apple'siPodandiPhonechargers indicate the available current by voltages on the D− and D+ lines (sometimes also called "Apple Brick ID" ). When D+ = D− = 2.0 V, the device may pull up to 900 mA. When D+ = 2.0 V and D− = 2.8 V, the device may pull up to 1 A of current.[54]When D+ = 2.8 V and D− = 2.0 V, the device may pull up to 2 A of current.[55]

Accessory charging adapters (ACA)

edit

Portable devices having aUSB On-The-Goport may want to charge and access a USB peripheral simultaneously, yet having only a single port (both due to On-The-Go and space requirement) prevents this.Accessory charging adapters (ACA)are devices that provide portable charging power to an On-The-Go connection between host and peripheral.

ACAs have three ports: the OTG port for the portable device, which is required to have a Micro-A plug on a captive cable; the accessory port, which is required to have a Micro-AB or type-A receptacle; and the charging port, which is required to have a Micro-B receptacle, or type-A plug or charger on a captive cable. The ID pin of the OTG port is not connected within plug as usual, but to the ACA itself, where signals outside the OTG floating and ground states are used for ACA detection and state signaling. The charging port does not pass data, but does use the D± signals for charging port detection. The accessory port acts as any other port. When appropriately signaled by the ACA, the portable device can charge from the bus power as if there were a charging port present; any OTG signals over bus power are instead passed to the portable device via the ID signal. Bus power is also provided to the accessory port from the charging port transparently.[51]

USB Power Delivery

edit
The USB Type-C Charging logo (USB420 Gbps port)
USB PD Rev. 1.0 source profiles[56]
Profile +5 V +12 V +20 V
0 Reserved
1 2.0 A, 10 W[a] — —
2 1.5 A, 18 W
3 3.0 A, 36 W
4 3.0 A, 60 W
5 5.0 A, 60 W 5.0 A, 100 W
  1. ^Default start-up profile
USB Power Delivery rev. 2.0/3.xpower rules
Power Minimum USB‑C
cable required 		Voltage Current
≤ 15 W Any[A][57][58][59] 5 V ≤ 3.0 A
≤ 27 W 9 V
≤ 45 W 15 V
≤ 60 W 20 V
≤ 100 W 5 A, or 100 W[B] 20 V ≤ 5.0 A
≤ 140 W[C] 240 W[B][D][59] 28 V ≤ 5.0 A
≤ 180 W[C] 36 V
≤ 240 W[C] 48 V
  1. ^60 Wlabel required on both plug bodies by
    current standard, not required on older cables
  2. ^abElectronically marked
  3. ^abcUSB PD Extended Power Range
  4. ^240 Wlabel required on both plug bodies
Power rule of USB Power Delivery Revision 3.1

In July 2012, the USB Promoters Group announced the finalization of theUSB Power Delivery(USB-PD) specification (USB PD rev. 1), an extension that specifies using certifiedPD awareUSB cables with standard USB Type-A and Type-B connectors to deliver increased power (more than 7.5 W maximum allowed by the previousUSB Battery Chargingspecification) to devices with greater power demands. (USB-PD A and B plugs have a mechanical mark while Micro plugs have a resistor or capacitor attached to the ID pin indicating the cable capability.) USB-PD Devices can request higher currents and supply voltages from compliant hosts—up to 2 A at 5 V (for a power consumption of up to 10 W), and optionally up to 3 A or 5 A at either 12 V (36 W or 60 W) or 20 V (60 W or 100 W).[60]In all cases, both host-to-device and device-to-host configurations are supported.[61]

The intent is to permit uniformly charging laptops, tablets, USB-powered disks and similarly higher-power consumer electronics, as a natural extension of existing European and Chinese mobile telephone charging standards. This may also affect the way electric power used for small devices is transmitted and used in both residential and public buildings.[62][56]The standard is designed to coexist with the previousUSB Battery Chargingspecification.[63]

The first Power Delivery specification (Rev. 1.0) defined six fixed power profiles for the power sources. PD-aware devices implement a flexible power management scheme by interfacing with the power source through a bidirectional data channel and requesting a certain level of electrical power, variable up to 5 A and 20 V depending on supported profile. The power configuration protocol can useBMCcoding over the CC (configuration channel) wire if one is present, or a 24 MHzBFSK-coded transmission channel on the VBUSline.[56]

The USB Power Delivery specification revision 2.0 (USB PD Rev. 2.0) has been released as part of the USB 3.1 suite.[57][64][65]It covers the USB-C cable and connector with a separate configuration channel, which now hosts aDC coupledlow-frequencyBMC-coded data channel that reduces the possibilities forRF interference.[66]Power Delivery protocols have been updated to facilitate USB-C features such as cable ID function, Alternate Mode negotiation, increased VBUScurrents, and VCONN-powered accessories.

As of USB Power Delivery specification revision 2.0, version 1.2, the six fixed power profiles for power sources have been deprecated.[67]USB PD Power Rules replace power profiles, defining four normative voltage levels at 5 V, 9 V, 15 V, and 20 V. Instead of six fixed profiles, power supplies may support any maximum source output power from 0.5 W to 100 W.

The USB Power Delivery specification revision 3.0 defines an optional Programmable Power Supply (PPS) protocol that allows granular control over VBUSoutput, allowing a voltage range of 3.3 to 21 V in 20 mV steps, and a current specified in 50 mA steps, to facilitate constant-voltage and constant-current charging. Revision 3.0 also adds extended configuration messages and fast role swap and deprecates the BFSK protocol.[58]: Table 6.26 [68][69]

The Certified USB Fast Charger logo indicating support for the Programmable Power Supply (PPS) protocol in USB Power Delivery (PD) chargers

On January 8, 2018, USB-IF announced the Certified USB Fast Charger logo for chargers that use the Programmable Power Supply (PPS) protocol from the USB Power Delivery 3.0 specification.[70]

In May 2021, the USB PD promoter group launched revision 3.1 of the specification.[59]Revision 3.1 adds Extended Power Range (EPR) mode which allows higher voltages of 28, 36, and 48 V, providing up to 240 W of power (48 V at 5 A), and the "Adjustable Voltage Supply" (AVS) protocol which allows specifying the voltage from a range of 15 to 48 V in 100 mV steps.[71][72]Higher voltages require electronically marked EPR cables that support 5 A operation and incorporate mechanical improvements required by the USB Type-C standard rev. 2.1; existing power modes are retroactively renamed Standard Power Range (SPR). In October 2021 Apple introduced a 140 W (28 V 5 A)GaNUSB PD charger with new MacBooks,[73]and in June 2023 Framework introduced a 180 W (36 V 5 A) GaN USB PD charger with the Framework 16.[74]

In October 2023, the USB PD promoter group launched revision 3.2 of the specification. The AVS protocol now works with the old standard power range (SPR), down to a minimum of 9 V.[75]: §10.2.2 

Prior to Power Delivery, mobile phone vendors used custom protocols to exceed the 7.5 W cap on theUSB Battery ChargingSpecification (BCS). For example, Qualcomm'sQuick Charge2.0 is able to deliver 18 W at a higher voltage, andVOOCdelivers 20 W at the normal 5 V.[76]Some of these technologies, such as Quick Charge 4, eventually became compatible with USB PD again.[77]

Charge controllers

edit

As of 2024 mainstream USB PD charging controllers support up to 100 W through a single port, with a few up to 140 W[78][79]and custom built up to 180 W.[80]

Sleep-and-charge ports

edit
A yellow USB port denoting sleep-and-charge

Sleep-and-charge USB ports can be used to charge electronic devices even when the computer that hosts the ports is switched off. Normally, when a computer is powered off the USB ports are powered down. This feature has also been implemented on some laptop docking stations allowing device charging even when no laptop is present.[81]On laptops, charging devices from the USB port when it is not being powered from AC drains the laptop battery; most laptops have a facility to stop charging if their own battery charge level gets too low.[82]

On Dell, HP and Toshiba laptops, sleep-and-charge USB ports are marked with the standard USB symbol with an added lightning bolt or battery icon on the right side.[83]Dell calls this featurePowerShare,[84]and it needs to be enabled in the BIOS. Toshiba calls itUSB Sleep-and-Charge.[85]OnAcer Inc.andPackard Belllaptops, sleep-and-charge USB ports are marked with a non-standard symbol (the lettersUSBover a drawing of a battery); the feature is calledPower-off USB.[86]Lenovocalls this featureAlways On USB.[87]

Mobile device charger standards

edit
Main article:Universal charger

In China

edit

As of 14 June 2007,all newmobile phonesapplying for a license inChinaare required to use a USB port as a power port for battery charging.[88][89]This was the first standard to use the convention of shorting D+ and D− in the charger.[90]

OMTP/GSMA Universal Charging Solution

edit

In September 2007, theOpen Mobile Terminal Platformgroup (a forum of mobile network operators and manufacturers such asNokia,Samsung,Motorola,Sony Ericsson,andLG) announced that its members had agreed on Micro-USB as the future common connector for mobile devices.[91][92]

TheGSM Association(GSMA) followed suit on February 17, 2009,[93][94][95][96]and on April 22, 2009, this was further endorsed by theCTIA – The Wireless Association,[97]with theInternational Telecommunication Union(ITU) announcing on October 22, 2009, that it had also embraced the Universal Charging Solution as its "energy-efficient one-charger-fits-all new mobile phone solution," and added: "Based on the Micro-USB interface, UCS chargers will also include a 4-star or higher efficiency rating—up to three times more energy-efficient than an unrated charger."[98]

EU smartphone power supply standard

edit

In June 2009, theEuropean Commissionorganized a voluntary Memorandum of Understanding (MoU) to adopt micro-USB as a common standard for charging smartphones marketed in theEuropean Union.The specification was called thecommon external power supply.The MoU lasted until 2014. The common EPS specification (EN 62684:2010) references the USB Battery Charging Specification and is similar to the GSMA/OMTP and Chinese charging solutions.[99][100]In January 2011, theInternational Electrotechnical Commission (IEC)released its version of the (EU's) common EPS standard as IEC 62684:2011.[101]

In 2022, theRadio Equipment Directive 2022/2380made USB-C compulsory as a mobile phone charging standard from 2024, and for laptops from 2026.[102]

Faster-charging standards

edit

A variety of (non-USB) standards support charging devices faster than theUSB Battery Chargingstandard. When a device doesn't recognize the faster-charging standard, generally the device and the charger fall back to the USB battery-charging standard of 5 V at 1.5 A (7.5 W). When a device detects it is plugged into a charger with a compatible faster-charging standard, the device pulls more current or the device tells the charger to increase the voltage or both to increase power (the details vary between standards).[103]

Such standards include:[103][104]

Non-standard devices

edit

Some USB devices require more power than is permitted by the specifications for a single port. This is common for external hard andoptical disc drives,and generally for devices withmotorsorlamps.Such devices can use anexternal power supply,which is allowed by the standard, or use a dual-input USB cable, one input of which is for power and data transfer, the other solely for power, which makes the device a non-standard USB device. Some USB ports and external hubs can, in practice, supply more power to USB devices than required by the specification but a standard-compliant device may not depend on this.

In addition to limiting the total average power used by the device, the USB specification limits theinrush current(i.e., the current used to charge decoupling andfilter capacitors) when the device is first connected. Otherwise, connecting a device could cause problems with the host's internal power. USB devices are also required to automatically enter ultra low-power suspend mode when the USB host is suspended. Nevertheless, many USB host interfaces do not cut off the power supply to USB devices when they are suspended.[105]

Some non-standard USB devices use the 5 V power supply without participating in a proper USB network, which negotiates power draw with the host interface. Examples include USB-powered keyboard lights, fans, mug coolers and heaters, battery chargers, miniaturevacuum cleaners,and even miniaturelava lamps.In most cases, these items contain no digital circuitry, and thus are not standard-compliant USB devices. This may cause problems with some computers, such as drawing too much current and damaging circuitry. Prior to the USB Battery Charging Specification, the USB specification required that devices connect in a low-power mode (100 mA maximum) and communicate their current requirements to the host, which then permits the device to switch into high-power mode.

Some devices, when plugged into charging ports, draw even more power (10 watts) than the Battery Charging Specification allows—theiPadis one such device;[106]it negotiates the current pull with data pin voltages.[54]Barnes & NobleNook Colordevices also require a special charger that runs at 1.9 A.[107]

PoweredUSB

edit
Main article:PoweredUSB

PoweredUSB is a proprietary extension that adds four pins supplying up to 6 A at 5 V, 12 V, or 24 V. It is commonly used inpoint of salesystems to power peripherals such asbarcode readers,credit card terminals,and printers.

See also

edit

References

edit
  1. ^abcdefgUniversal Serial Bus Specification(Technical report) (Revision 2.0 ed.). USB-IF. 2000-04-27. 6.4.4 Prohibited Cable Assemblies.
  2. ^abUniversal Serial Bus 3.0 Specification: Revision 1.0.2011-06-06. p. 531. Archived fromthe originalon 2013-12-30.
  3. ^ab"USB 2.0 Specification Engineering Change Notice (ECN) #1: Mini-B connector"(PDF).2000-10-20. Archived fromthe original(PDF)on 2015-04-12.Retrieved2019-04-28– via USB.org.
  4. ^"USB connector guide".C2G.Archivedfrom the original on 2014-04-21.Retrieved2013-12-02.
  5. ^abcde"Universal Serial Bus Cables and Connectors Class Document – Revision 2.0"(PDF).USB Implementers Forum. August 2007. Archived fromthe original(PDF)on 2014-06-11.
  6. ^Howse, Brett."USB Type-C Connector Specifications Finalized".AnandTech.Archivedfrom the original on 2017-03-18.Retrieved2017-04-24.
  7. ^"USB Pinout".UsbPinout.net.Archived fromthe originalon 2014-06-17.
  8. ^abc"Universal Serial Bus Micro-USB Cables and Connectors Specification"(PDF).USB Implementers Forum. 2007-04-04.Archived(PDF)from the original on 2015-11-15.Retrieved2015-01-31.
  9. ^"Universal Serial Bus Revision 3.0 Specification, Sections 3.1.1.1 and 5.3.1.3".Usb.org.Archived fromthe original(ZIP)on 2014-05-19.Retrieved2019-04-28.
  10. ^Quinnell, Richard A. (1996-10-24)."USB: a neat package with a few loose ends".EDN Magazine.Reed.Archivedfrom the original on 2013-05-23.Retrieved2013-02-18.
  11. ^"What is the Difference between USB Type A and USB Type B Plug/Connector?".Archivedfrom the original on 2017-02-07.
  12. ^ab"Deprecation of the Mini-A and Mini-AB Connectors"(PDF)(Press release). USB Implementers Forum. 2007-05-27. Archived fromthe original(PDF)on 2009-03-06.Retrieved2009-01-13.
  13. ^"ID Pin Resistance on Mini B-plugs and Micro B-plugs Increased to 1 Mohm".USB IF Compliance Updates. December 2009.Archivedfrom the original on 2011-07-20.Retrieved2010-03-01.
  14. ^abUniversal Serial Bus Cables and Connectors Class Document(PDF),Revision 2.0, USB Implementers Forum, August 2007, p. 6,archived(PDF)from the original on 2015-04-27,retrieved2014-08-17
  15. ^"Mobile phones to adopt new, smaller USB connector"(PDF)(Press release). USB Implementers Forum. 2007-01-04.Archived(PDF)from the original on 2007-01-08.Retrieved2007-01-08.
  16. ^"Micro-USB mobile phone/smartphone cable connector pinout diagram".pinoutguide.com.2012-11-16.Archivedfrom the original on 2024-05-27.Retrieved2024-05-29.
  17. ^ab"Universal Serial Bus Micro-USB Cables and Connectors Specification to the USB 2.0 Specification, Revision 1.01".USB Implementers Forum. 2007-04-07. Archived fromthe original(ZIP)on 2012-02-07.Retrieved2010-11-18.Section 1.3: Additional requirements for a more rugged connector that is durable past 10,000 cycles and still meets the USB 2.0 specification for mechanical and electrical performance was also a consideration. The Mini-USB could not be modified and remain backward compatible to the existing connector as defined in the USB OTG specification.
  18. ^"OMTP Local Connectivity: Data Connectivity".Open Mobile Terminal Platform.2007-09-17. Archived fromthe originalon 2008-10-15.Retrieved2009-02-11.
  19. ^"Universal phone charger standard approved—One-size-fits-all solution will dramatically cut waste and GHG emissions".ITU(press release). Pressinfo. 2009-10-22.Archivedfrom the original on 2009-11-05.Retrieved2009-11-04.
  20. ^"Commission welcomes new EU standards for common mobile phone charger".Press Releases.Europa. 2010-12-29.Archivedfrom the original on 2011-03-19.Retrieved2011-05-22.
  21. ^New EU standards for common mobile phone charger(press release), Europa,archivedfrom the original on 2011-01-03
  22. ^The following 10 biggest mobile phone companies have signed the MoU: Apple, LG, Motorola, NEC, Nokia, Qualcomm, Research In Motion, Samsung, Sony Ericsson, Texas Instruments(press release), Europa,archivedfrom the original on 2009-07-04
  23. ^"Nice Micro-USB Adapter Apple, Now Sell It Everywhere".Giga om.2011-10-05.Archivedfrom the original on 2012-08-26.
  24. ^"Apple's Lightning to Micro-USB adapter now available in US, not just Europe anymore",Engadget,2012-11-03,archivedfrom the original on 2017-06-26
  25. ^abHowse, Brett (2014-08-12)."USB Type-C Connector Specifications Finalized".Archivedfrom the original on 2014-12-28.Retrieved2014-12-28.
  26. ^Hruska, Joel (2015-03-13)."USB-C vs. USB 3.1: What's the difference?".ExtremeTech.Archivedfrom the original on 2015-04-11.Retrieved2015-04-09.
  27. ^Ngo, Dong (2014-08-22)."USB Type-C: One Cable to Connect Them All".c.net.Archived fromthe originalon 2015-03-07.Retrieved2014-12-28.
  28. ^"Technical Introduction of the New USB Type-C Connector".Archived fromthe originalon 2014-12-29.Retrieved2014-12-29.
  29. ^Smith, Ryan (2014-09-22)."DisplayPort Alternate Mode for USB Type-C Announced - Video, Power, & Data All Over Type-C".AnandTech.Archivedfrom the original on 2014-12-18.Retrieved2014-12-28.
  30. ^Universal Serial Bus Type-C Cable and Connector SpecificationRevision 1.1 (April 3, 2015), section 2.2, page 20
  31. ^abcUniversal Serial Bus Type-C Cable and Connector Specification, Release 2.2.USB Implementers Forum(Technical report). USB 3.0 Promoter Group. October 2022.Retrieved2023-04-12.
  32. ^"On-The-Go and Embedded Host Supplement to the USB Revision 3.0 Specification"(PDF).USB.org.Revision 1.1. 2012-05-10.
  33. ^"Proprietary Cables vs Standard USB".anythingbutipod.com.2008-04-30. Archived fromthe originalon 2013-11-13.Retrieved2013-10-29.
  34. ^Friedman, Lex (2013-02-25)."Review: Logitech's Ultrathin mini keyboard cover makes the wrong tradeoffs".macworld.com.Archivedfrom the original on 2013-11-03.Retrieved2013-10-29.
  35. ^"What Is the USB 3.0 Cable Difference".Hantat. 2009-05-18. Archived fromthe originalon 2011-12-11.Retrieved2011-12-12.
  36. ^"USB Cable Length Limitations"(PDF).cablesplususa.com.2010-11-03. Archived fromthe original(PDF)on 2014-10-11.Retrieved2014-02-02.
  37. ^"What is the Maximum Length of a USB Cable?".Techwalla.com.Archivedfrom the original on 2017-12-01.Retrieved2017-11-18.
  38. ^ab"USB Frequently Asked Questions: Cables and Long-Haul Solutions".USB.org.Archived fromthe originalon 2014-01-15.Retrieved2023-05-22.
  39. ^Axelson, Jan."USB 3.0 Developers FAQ".Archivedfrom the original on 2016-12-20.Retrieved2016-10-20.
  40. ^"USB Type-C Revision 1.0"(PDF).USB 3.0 Promoter Group.2021-03-01.Archived(PDF)from the original on 2021-11-03.Retrieved2021-11-03.
  41. ^"USB ECN USB 2.0 VBUS Max Limit".USB-IF.2021-11-03.Archivedfrom the original on 2021-11-03.Retrieved2021-11-03.
  42. ^"Battery Charging v1.2 Spec and Adopters Agreement"(PDF (Zipped)).USB.org.2015-03-15. Table 5-1 Voltages.Archived(PDF (Zipped))from the original on 2021-11-03.Retrieved2021-11-03.
  43. ^abc"USB Power Delivery Specifications 2.0 and 3"(PDF (Zipped)).USB.org.2021-10-26.Archived(PDF (Zipped))from the original on 2021-11-03.Retrieved2021-11-03.
  44. ^"USB.org".USB.org.Archivedfrom the original on 2012-06-19.Retrieved2010-06-22.
  45. ^"Universal Serial Bus 1.1 Specification"(PDF).cs.ucr.edu.1998-09-23. pp. 150, 158.Archived(PDF)from the original on 2015-01-02.Retrieved2014-11-24.
  46. ^"Universal Serial Bus 2.0 Specification, Section 7.2.1.3 Low-power Bus-powered Functions"(ZIP).usb.org.2000-04-27.Archivedfrom the original on 2013-09-10.Retrieved2014-01-11.
  47. ^"Universal Serial Bus 2.0 Specification, Section 7.2.1.4 High-power Bus-powered Functions"(ZIP).usb.org.2000-04-27.Archivedfrom the original on 2013-09-10.Retrieved2014-01-11.
  48. ^"Roundup: 2.5-inch Hard Disk Drives with 500 GB, 640 GB and 750 GB Storage Capacities (page 17)".xbitlabs.com.2010-06-16. Archived fromthe originalon 2010-06-28.Retrieved2010-07-09.
  49. ^"I have the drive plugged in but I cannot find the drive in" My Computer ", why?".hitachigst.com.Archived fromthe originalon 2011-02-15.Retrieved2012-03-30.
  50. ^"USB-IF Compliance Updates".Compliance.usb.org.2011-09-01.Archivedfrom the original on 2014-02-03.Retrieved2014-01-22.
  51. ^abcd"Battery Charging Specification, Revision 1.2".USB Implementers Forum. 2012-03-15.Archivedfrom the original on 2021-03-10.Retrieved2021-08-13.
  52. ^"Battery Charging Specification, Revision 1.1".USB Implementers Forum. 2009-04-15. Archived fromthe originalon 2014-03-29.Retrieved2009-09-23.
  53. ^"Battery Charging v1.2 Spec and Adopters Agreement"(Zip).USB Implementers Forum. 2012-03-15.Archivedfrom the original on 2014-10-06.Retrieved2021-05-13.
  54. ^ab"Minty Boost — The mysteries of Apple device charging".Lady Ada.2011-05-17. Archived fromthe originalon 2012-03-28.
  55. ^"Modify a cheap USB charger to feed an iPod, iPhone".2011-10-05.Archivedfrom the original on 2011-10-07.
  56. ^abc"USB Power Delivery — Introduction"(PDF).2012-07-16. Archived fromthe original(PDF)on 2013-01-23.Retrieved2013-01-06.
  57. ^ab"10 Power Rules",Universal Serial Bus Power Delivery Specification revision 2.0, version 1.2,USB Implementers Forum, 2016-03-25,archivedfrom the original on 2024-05-26,retrieved2016-04-09
  58. ^ab"10 Power Rules",Universal Serial Bus Power Delivery Specification revision 3.0, version 1.1,USB Implementers Forum,archivedfrom the original on 2024-05-26,retrieved2017-09-05
  59. ^abc"10 Power Rules",Universal Serial Bus Power Delivery Specification revision 3.1, version 1.0,USB Implementers Forum,retrieved2017-09-05
  60. ^Burgess, Rick (2013-04-22)."USB 3.0 SuperSpeed Update to Eliminate Need for Chargers".TechSpot.
  61. ^"USB 3.0 Promoter Group Announces Availability of USB Power Delivery Specification"(PDF).2012-07-18.Archived(PDF)from the original on 2013-01-20.Retrieved2013-01-16.
  62. ^"Edison's revenge".The Economist.2013-10-19.Archivedfrom the original on 2013-10-22.Retrieved2013-10-23.
  63. ^"USB Power Delivery".
  64. ^"USB 3.1 Specification".Archivedfrom the original on 2012-06-19.Retrieved2014-11-11.
  65. ^"USB Power Delivery v2.0 Specification Finalized - USB Gains Alternate Modes".AnandTech.com.
  66. ^"USB Future Specifications Industry Reviews"(PDF).Archived(PDF)from the original on 2014-07-29.Retrieved2014-08-10.
  67. ^"A. Power Profiles",Universal Serial Bus Power Delivery Specification revision 2.0, version 1.2,USB Implementers Forum, 2016-03-25, archived fromthe originalon 2016-04-12,retrieved2016-04-09
  68. ^"USB Power Delivery"(PDF).usb.org.USB-IF. 2016-10-20. Archived fromthe original(PDF)on 2016-12-20.
  69. ^Waters, Deric (2016-07-14)."USB Power Delivery 2.0 vs 3.0".E2E.TI.com.Archivedfrom the original on 2017-07-30.Retrieved2017-07-30.
  70. ^"USB-IF Introduces Fast Charging to Expand its Certified USB Charger Initiative"(Press release). 2018-01-09.Retrieved2018-01-10.
  71. ^USB-PD boosts USB-C power delivery to 240W at 48V.Nick Flaherty, EENews. May 28, 2021
  72. ^USB-C Power Delivery Hits 240W with Extended Power Range.Ganesh T S, Anandtech. May 28, 2021
  73. ^"Teardown of Brand New Apple 140W USB-C GaN Charger".2021-10-30.Retrieved2021-11-15.
  74. ^"Framework Laptop 16 Deep Dive - 180W Power Adapter".Framework.Retrieved2024-02-28.
  75. ^Universal Serial Bus Power Delivery Specification revision 3.2, version 1.0,USB Implementers Forum,retrieved2023-02-13
  76. ^"How fast can a fast-charging phone charge if a fast-charging phone can charge really fast?".CNet.Retrieved2016-12-04.
  77. ^"Qualcomm Announces Quick Charge 4: Supports USB Type-C Power Delivery".AnandTech.Retrieved2016-12-13.
  78. ^"Teardown of Anker 140W PD3.1 USB-C GaN Charger (717 Charger)".2022-10-26.
  79. ^140W PD 3.1 Power Adapters, the future of USB C Power Delivery,2023-01-02,retrieved2024-03-08
  80. ^"Framework Laptop 16 Deep Dive - 180W Power Adapter".Framework.Retrieved2024-03-08.
  81. ^"ThinkPad Ultra Dock".lenovo.com.Archivedfrom the original on 2016-09-17.Retrieved2016-09-16.
  82. ^"Toshiba NB200 User Manual"(PDF).UK. 2009-03-01.Archived(PDF)from the original on 2014-02-19.Retrieved2014-01-26.
  83. ^"USB PowerShare Feature".dell.com.2019-09-15.Retrieved2020-06-15.
  84. ^"USB PowerShare Feature".dell.com.2013-06-05.Archivedfrom the original on 2013-11-08.Retrieved2013-12-04.
  85. ^"USB Sleep-and-Charge Ports".toshiba.com.Archivedfrom the original on 2014-12-14.Retrieved2014-12-21.
  86. ^"USB Charge Manager".packardbell.com.Retrieved2014-04-25.
  87. ^"How to configure the system to charge devices over USB port when it is off - idea/Lenovo laptops - NL".support.lenovo.com.Retrieved2020-04-07.
  88. ^Cai Yan (2007-05-31)."China to enforce universal cell phone charger".EE Times.Archivedfrom the original on 2007-09-29.Retrieved2007-08-25.
  89. ^The Chinese technical standard:"YD/T 1591-2006, Technical Requirements and Test Method of Charger and Interface for Mobile Telecommunication Terminal Equipment"(PDF).Dian yuan(in Chinese). Archived fromthe original(PDF)on 2011-05-15.
  90. ^Lam, Crystal; Liu, Harry (2007-10-22)."How to conform to China's new mobile phone interface standards".Wireless Net DesignLine.Archivedfrom the original on 2014-05-14.Retrieved2010-06-22.
  91. ^"Pros Seem to Outdo Cons in New Phone Charger Standard".News.com.2007-09-20.Retrieved2007-11-26.
  92. ^"Broad Manufacturer Agreement Gives Universal Phone Cable Green Light"(Press release). OTMP. 2007-09-17. Archived fromthe originalon 2009-06-29.Retrieved2007-11-26.
  93. ^"Agreement on Mobile phone Standard Charger"(Press release). GSM World. Archived fromthe originalon 2009-02-17.
  94. ^"Common Charging and Local Data Connectivity".Open Mobile Terminal Platform.2009-02-11. Archived fromthe originalon 2009-03-29.Retrieved2009-02-11.
  95. ^"Universal Charging Solution ~ GSM World".GSM world. Archived fromthe originalon 2010-06-26.Retrieved2010-06-22.
  96. ^"Meeting the challenge of the universal charge standard in mobile phones".Planet Analog. Archived fromthe originalon 2012-09-09.Retrieved2010-06-22.
  97. ^"The Wireless Association Announces One Universal Charger Solution to Celebrate Earth Day"(Press release). CTIA. 2009-04-22. Archived fromthe originalon 2010-12-14.Retrieved2010-06-22.
  98. ^"Universal Phone Charger Standard Approved"(Press release). ITU. 2009-10-22. Archived fromthe originalon 2010-03-27.Retrieved2023-05-22.
  99. ^"chargers".EU: EC. 2009-06-29. Archived fromthe originalon 2009-10-23.Retrieved2010-06-22.
  100. ^"Europe gets universal cellphone charger in 2010".Wired.2009-06-13.Archivedfrom the original on 2010-08-18.Retrieved2010-06-22.
  101. ^"One size-fits-all mobile phone charger: IEC publishes first globally relevant standard".International Electrotechnical Commission. 2011-02-01.Archivedfrom the original on 2012-01-03.Retrieved2012-02-20.
  102. ^"Common charger: MEPs agree on proposal to reduce electronic waste".European Parliament.2022-04-20. Archived fromthe originalon 2022-04-22.Retrieved2022-04-20.
  103. ^abKumar, Ajay; Winkelman, Steven; LeClair, Dave (2022-07-27)."What Is Fast Charging?".PCMag.Retrieved2023-05-21.
  104. ^Hill, Simon; Revilla, Andre; Chandler, Simon (2021-07-01)."How does fast charging work? Here's every single standard compared".Digital Trends.Retrieved2022-08-20.
  105. ^"Part 2 - Electrical".MQP Electronics.Archivedfrom the original on 2014-12-24.Retrieved2014-12-29.
  106. ^"Watt to Know About iPhone & iPad Power Adapters | Analysis".The Mac Observer.Archivedfrom the original on 2011-12-10.Retrieved2011-12-12.
  107. ^"Nook Color charger uses special Micro-USB connector".barnesandnoble.com.2011-07-03. Archived fromthe originalon 2012-02-11.
Retrieved from "https://en.wikipedia.org/w/index.php?title=USB_hardware&oldid=1249620052"