Air–fuel ratio

Air–fuel ratio(AFR) is the mass ratio ofairto a solid, liquid, or gaseousfuelpresent in acombustionprocess. The combustion may take place in a controlled manner such as in aninternal combustion engineor industrial furnace, or may result in an explosion (e.g., adust explosion),The air–fuel ratio determines whether a mixture is combustible at all, how much energy is being released, and how much unwanted pollutants are produced in the reaction. Typically a range of fuel to air ratios exists, outside of which ignition will not occur. These are known as the lower and upper explosive limits.

In aninternal combustion engineor industrial furnace, the air–fuel ratio is an important measure for anti-pollution and performance-tuning reasons. If exactly enough air is provided to completely burn all of the fuel (stoichiometriccombustion), the ratio is known as thestoichiometric mixture,often abbreviated tostoich.Ratios lower than stoichiometric (where the fuel is in excess) are considered "rich". Rich mixtures are less efficient, but may produce more power and burn cooler. Ratios higher than stoichiometric (where the air is in excess) are considered "lean". Lean mixtures are more efficient but may cause higher temperatures, which can lead to the formation ofnitrogen oxides.Some engines are designed with features to allowlean-burn.For precise air–fuel ratio calculations, theoxygencontent of combustion air should be specified because of differentair densitydue to different altitude or intake air temperature, possible dilution by ambientwater vapor,or enrichment by oxygen additions.

Air-fuel ratio meters

Anair-fuel ratio metermonitors the air–fuel ratio of aninternal combustion engine.Also calledair–fuel ratio gauge,air–fuel meter,orair–fuel gauge,it reads the voltage output of anoxygen sensor,sometimes also calledAFR sensoror lambda sensor.

The original narrow-band oxygen sensors became factory installed standard in the late 1970s and early 1980s. In recent years a newer and much more accurate wide-band sensor, though more expensive, has become available.

Most stand-alone narrow-band meters have 10LEDsand some have more. Also common, narrow band meters in round housings with the standard mounting52 and 67 mm (2+1⁄16and2+5⁄8in) diameters, as other types of car 'gauges'. These usually have 10 or 20 LEDs. Analogue 'needle' style gauges are also available.

Internal combustion engines

In theory, a stoichiometric mixture has just enough air to completely burn the available fuel. In practice, this is never quite achieved, due primarily to the very short time available in an internal combustion engine for each combustion cycle.

Most of the combustion process is completed in approximately 2 milliseconds at an engine speed of6,000revolutions per minute(100 revolutions per second, or 10 milliseconds per revolution of the crankshaft. For a four-stroke engine this would mean 5 milliseconds for each piston stroke, and 20 milliseconds to complete one 720 degreeOtto cycle). This is the time that elapses from the spark plug firing until 90% of the fuel–air mix is combusted, typically some 80 degrees of crankshaft rotation later.Catalytic convertersare designed to work best when theexhaust gasespassing through them are the result of nearly perfect combustion.

A perfectly stoichiometric mixture burns very hot and can damage engine components if the engine is placed under high load at this fuel–air mixture. Due to the high temperatures at this mixture, the detonation of the fuel-air mix while approaching or shortly after maximum cylinder pressure is possible under high load (referred to asknockingor pinging), specifically a "pre-detonation" event in the context of a spark-ignition engine model. Such detonation can cause serious engine damage as the uncontrolled burning of the fuel-air mix can create very high pressures in the cylinder. As a consequence, stoichiometric mixtures are only used under light to low-moderate load conditions. For acceleration and high-load conditions, a richer mixture (lower air–fuel ratio) is used to produce cooler combustion products (thereby utilizingevaporative cooling), and so avoid overheating of thecylinder head,and thus prevent detonation.

Engine management systems

Thestoichiometricmixture for a gasoline engine is the ideal ratio of air to fuel that burns all fuel with no excess air. Forgasolinefuel, the stoichiometric air–fuel mixture is about 14.7:1i.e. for every one gram of fuel, 14.7 grams of air are required. For pureoctanefuel, the oxidation reaction is:

25 O₂+ 2 C₈H₁₈→ 16 CO₂+ 18 H₂O + energy

Any mixture greater than 14.7:1 is considered alean mixture;any less than 14.7:1 is arich mixture– given perfect (ideal) "test" fuel (gasoline consisting of solelyn-heptaneandiso-octane). In reality, most fuels consist of a combination of heptane, octane, a handful of otheralkanes,plus additives including detergents, and possibly oxygenators such as MTBE (methyltert-butyl ether) orethanol/methanol.These compounds all alter the stoichiometric ratio, with most of the additives pushing the ratio downward (oxygenators bring extra oxygen to the combustion event in liquid form that is released at the time of combustions; forMTBE-laden fuel, a stoichiometric ratio can be as low as 14.1:1). Vehicles that use anoxygen sensoror other feedback loops to control fuel to air ratio (lambda control), compensate automatically for this change in the fuel's stoichiometric rate by measuring the exhaust gas composition and controlling fuel volume. Vehicles without such controls (such as most motorcycles until recently, and cars predating the mid-1980s) may have difficulties running certain fuel blends (especially winter fuels used in some areas) and may require differentcarburetorjets (or otherwise have the fueling ratios altered) to compensate. Vehicles that useoxygen sensorscan monitor the air–fuel ratio with anair–fuel ratio meter.

Other types of engines

In the typical air to natural gas combustion burner, a double-cross limit strategy is employed to ensure ratio control. (This method was used in World War II).The strategy involves adding the opposite flow feedback into the limiting control of the respective gas (air or fuel). This assures ratio control within an acceptable margin.

Other terms used

There are other terms commonly used when discussing the mixture of air and fuel in internal combustion engines.

Mixture

Mixtureis the predominant word that appears in training texts, operation manuals, and maintenance manuals in the aviation world.

Air–fuel ratio is the ratio between themassof air and the mass of fuel in the fuel–air mix at any given moment. The mass is the mass of all constituents that compose the fuel and air, whether combustible or not. For example, a calculation of the mass of natural gas—which often containscarbon dioxide(CO
₂),nitrogen(N
₂), and variousalkanes—includes the mass of the carbon dioxide, nitrogen and all alkanes in determining the value ofm_fuel.

For pureoctanethe stoichiometric mixture is approximately 15.1:1, orλof 1.00 exactly.

In naturally aspirated engines powered by octane, maximum power is frequently reached at AFRs ranging from 12.5 to 13.3:1 orλof 0.850 to 0.901.

The air-fuel ratio of 12:1 is considered as the maximum output ratio, whereas the air-fuel ratio of 16:1 is considered as the maximum fuel economy ratio.

Fuel–air ratio (FAR)

Fuel–air ratiois commonly used in thegas turbineindustry as well as in government studies ofinternal combustion engine,and refers to the ratio of fuel to the air.

$\mathrm {FAR} ={\frac {1}{\mathrm {AFR} }}$

Air–fuel equivalence ratio (λ)

Air–fuel equivalence ratio,λ(lambda), is the ratio of actual AFR to stoichiometry for a given mixture.λ= 1.0 is at stoichiometry, rich mixturesλ< 1.0, and lean mixturesλ> 1.0.

There is a direct relationship betweenλand AFR. To calculate AFR from a givenλ,multiply the measuredλby the stoichiometric AFR for that fuel. Alternatively, to recoverλfrom an AFR, divide AFR by the stoichiometric AFR for that fuel. This last equation is often used as the definition ofλ:

$\lambda ={\frac {\mathrm {AFR} }{\mathrm {AFR} _{\text{stoich}}}}$

Because the composition of common fuels varies seasonally, and because many modern vehicles can handle different fuels when tuning, it makes more sense to talk aboutλvalues rather than AFR.

Most practical AFR devices actually measure the amount of residual oxygen (for lean mixes) or unburnt hydrocarbons (for rich mixtures) in the exhaust gas.

Fuel–air equivalence ratio (Φ)

Thefuel–air equivalence ratio,Φ(phi), of a system is defined as the ratio of the fuel-to-oxidizer ratio to the stoichiometric fuel-to-oxidizer ratio. Mathematically,

$\phi ={\frac {\mbox{fuel-to-oxidizer ratio}}{({\mbox{fuel-to-oxidizer ratio}})_{\text{st}}}}={\frac {m_{\text{fuel}}/m_{\text{ox}}}{\left(m_{\text{fuel}}/m_{\text{ox}}\right)_{\text{st}}}}={\frac {n_{\text{fuel}}/n_{\text{ox}}}{\left(n_{\text{fuel}}/n_{\text{ox}}\right)_{\text{st}}}}$

wheremrepresents the mass,nrepresents a number of moles, subscript st stands for stoichiometric conditions.

The advantage of using equivalence ratio over fuel–oxidizer ratio is that it takes into account (and is therefore independent of) both mass and molar values for the fuel and the oxidizer. Consider, for example, a mixture of one mole ofethane(C
₂H
₆) and one mole ofoxygen(O
₂). The fuel–oxidizer ratio of this mixture based on the mass of fuel and air is

${\frac {m_{{\ce {C2H6}}}}{m_{{\ce {O2}}}}}={\frac {1\times (2\times 12+6\times 1)}{1\times (2\times 16)}}={\frac {30}{32}}=0.9375$

and the fuel-oxidizer ratio of this mixture based on the number of moles of fuel and air is

${\frac {n_{{\ce {C2H6}}}}{n_{{\ce {O2}}}}}={\frac {1}{1}}=1$

Clearly the two values are not equal. To compare it with the equivalence ratio, we need to determine the fuel–oxidizer ratio of ethane and oxygen mixture. For this we need to consider the stoichiometric reaction of ethane and oxygen,

C₂H₆+7⁄2O₂→ 2 CO₂+ 3 H₂O

This gives

$({\text{fuel-to-oxidizer ratio based on mass}})_{\text{st}}=\left({\frac {m_{{\ce {C2H6}}}}{m_{{\ce {O2}}}}}\right)_{\text{st}}={\frac {1\times (2\times 12+6\times 1)}{3.5\times (2\times 16)}}={\frac {30}{112}}=0.268$

$({\text{fuel-to-oxidizer ratio based on number of moles}})_{\text{st}}=\left({\frac {n_{{\ce {C2H6}}}}{n_{{\ce {O2}}}}}\right)_{\text{st}}={\frac {1}{3.5}}=0.286$

Thus we can determine the equivalence ratio of the given mixture as

$\phi ={\frac {m_{{\ce {C2H6}}}/m_{{\ce {O2}}}}{\left(m_{{\ce {C2H6}}}/m_{{\ce {O2}}}\right)_{\text{st}}}}={\frac {0.938}{0.268}}=3.5$

or, equivalently, as

$\phi ={\frac {n_{{\ce {C2H6}}}/n_{{\ce {O2}}}}{\left(n_{{\ce {C2H6}}}/n_{{\ce {O2}}}\right)_{\text{st}}}}={\frac {1}{0.286}}=3.5$

Another advantage of using the equivalence ratio is that ratios greater than one always mean there is more fuel in the fuel–oxidizer mixture than required for complete combustion (stoichiometric reaction), irrespective of the fuel and oxidizer being used—while ratios less than one represent a deficiency of fuel or equivalently excess oxidizer in the mixture. This is not the case if one uses fuel–oxidizer ratio, which takes different values for different mixtures.

The fuel–air equivalence ratio is related to the air–fuel equivalence ratio (defined previously) as follows:

$\phi ={\frac {1}{\lambda }}$

Mixture fraction

Further information:Mixture fraction

The relative amounts of oxygen enrichment and fuel dilution can be quantified by themixture fraction,Z, defined as

$Z=\left[{\frac {sY_{\mathrm {F} }-Y_{\mathrm {O} }+Y_{\mathrm {O,0} }}{sY_{\mathrm {F,0} }+Y_{\mathrm {O,0} }}}\right]$,

where

$s=\mathrm {AFR} _{\mathrm {stoich} }={\frac {W_{\mathrm {O} }\times v_{\mathrm {O} }}{W_{\mathrm {F} }\times v_{\mathrm {F} }}}$,

Y_F,0andY_O,0represent the fuel and oxidizer mass fractions at the inlet,W_FandW_Oare the species molecular weights, andv_Fandv_Oare the fuel and oxygen stoichiometric coefficients, respectively. The stoichiometric mixture fraction is

$Z_{\mathrm {st} }=\left[{\frac {1}{1+{\frac {Y_{\mathrm {F,0} }\times W_{\mathrm {O} }\times v_{\mathrm {O} }}{Y_{\mathrm {O,0} }\times W_{\mathrm {F} }\times v_{\mathrm {F} }}}}}\right]$

The stoichiometric mixture fraction is related toλ(lambda) andΦ(phi) by the equations

$Z_{\text{st}}={\frac {\lambda }{1+\lambda }}={\frac {1}{1+\phi }}$,

assuming

$\mathrm {AFR} ={\frac {Y_{\mathrm {O,0} }}{Y_{\mathrm {F,0} }}}$

Percent excess combustion air

Ideal stoichiometry

In industrialfired heaters,power plantsteam generators, and largegas-fired turbines,the more common terms are percent excess combustion air and percent stoichiometric air.For example, excess combustion air of 15 percent means that 15 percent more than the required stoichiometric air (or 115 percent of stoichiometric air) is being used.

A combustion control point can be defined by specifying the percent excess air (or oxygen) in theoxidant,or by specifying the percent oxygen in the combustion product.Anair–fuel ratio metermay be used to measure the percent oxygen in the combustion gas, from which the percent excess oxygen can be calculated from stoichiometry and amass balancefor fuel combustion. For example, for propane (C
₃H
₈) combustion between stoichiometric and 30 percent excess air (AFR_massbetween 15.58 and 20.3), the relationship between percent excess air and percent oxygen is:

${\begin{aligned}\mathrm {Mass\%\ O_{2}\ in\ propane\ combustion\ gas} &\approx -0.1433(\mathrm {\%\ excess\ O_{2}} )^{2}+0.214(\mathrm {\%\ excess\ O_{2}} )\\\mathrm {Volume\%\ O_{2}\ in\ propane\ combustion\ gas} &\approx -0.1208(\mathrm {\%\ excess\ O_{2}} )^{2}+0.186(\mathrm {\%\ excess\ O_{2}} )\end{aligned}}$

See also

• Adiabatic flame temperature
• AFR sensor
• Air–fuel ratio meter
• Mass flow sensor
• Combustion
• Stoichiometric air-to-fuel ratio of common fuels

External links

• HowStuffWorks:fuel injection,catalytic converter
• University of Plymouth:Engine Combustion primer
• Kamm, Richard W."Mixed Up About Fuel Mixtures?".Aircraft Maintenance Technology(February 2002). Archived fromthe originalon 2010-11-20.Retrieved2009-03-18.