Wikipedia

Self-healing material

Self-healing materialsare artificial or synthetically createdsubstancesthat have the built-in ability to automatically repair damages to themselves without any external diagnosis of the problem or human intervention. Generally, materials will degrade over time due tofatigue,environmental conditions, or damage incurred during operation.Cracksand other types of damage on a microscopic level have been shown to changethermal,electrical,andacousticalproperties of materials, and the propagation of cracks can lead to eventualfailureof the material. In general, cracks are hard to detect at an early stage, and manual intervention is required for periodic inspections and repairs. In contrast, self-healing materials counter degradation through the initiation of a repair mechanism that responds to the micro-damage.[1]: 1–2 Some self-healing materials are classed as smart structures, and can adapt to various environmental conditions according to their sensing and actuation properties.[1]: 145 

Animation 1.3D measurement of self-healing material from Tosoh Corporation measured by digital holographic microscopy. The surface has been scratched by a metallic tool.
Animation 2.Section of self-healing material recovering from a scratch

Although the most common types of self-healing materials arepolymersorelastomers,self-healing covers all classes of materials, includingmetals,ceramics,andcementitious materials.Healing mechanisms vary from an instrinsic repair of the material to the addition of a repair agent contained in a microscopic vessel. For a material to be strictly defined as autonomously self-healing, it is necessary that the healing process occurs without human intervention. Self-healing polymers may, however, activate in response to an external stimulus (light, temperature change, etc.) to initiate the healing processes.

A material that can intrinsically correct damage caused by normal usage could prevent costs incurred by material failure and lower costs of a number of different industrial processes through longer part lifetime, and reduction of inefficiency caused by degradation over time.[2]

History

edit
Main article:Roman concrete

Theancient Romansused a form oflime mortarthat has been found to have self-healing properties.[3]By 2014, geologist Marie Jackson and her colleagues had recreated the type of mortar used inTrajan's Marketand other Roman structures such as thePantheonand theColosseumand studied its response to cracking.[4]The Romans mixed a particular type ofvolcanic ashcalledPozzolane Rosse,from theAlban Hillsvolcano, withquicklimeandwater.They used it to bind together decimeter-sized chunks oftuff,an aggregate of volcanic rock.[3] As a result ofpozzolanic activityas the material cured, the lime interacted with other chemicals in the mix and was replaced by crystals of acalcium aluminosilicatemineral calledsträtlingite.Crystals of platey strätlingite grow in the cementitious matrix of the material including the interfacial zones where cracks would tend to develop. This ongoing crystal formation holds together the mortar and the coarse aggregate, countering crack formation and resulting in a material that has lasted for 1,900 years.[5][6]

Materials science

edit

Related processes in concrete have been studied microscopically since the 19th century.

Self healing materials only emerged as a widely recognized field of study in the 21st century. The first international conference on self-healing materials was held in 2007.[7]The field of self-healing materials is related tobiomimeticmaterials as well as to other novel materials and surfaces with the embedded capacity for self-organization, such as the self-lubricating andself-cleaningmaterials.[8]

Biomimetics

edit

Plants and animals have the capacity to seal and heal wounds. In all plants and animals examined, firstly a self-sealing phase and secondly a self-healing phase can be identified. In plants, the rapid self-sealing prevents the plants from desiccation and from infection by pathogenic germs. This gives time for the subsequent self-healing of the injury which in addition to wound closure also results in the (partly) restoration of mechanical properties of the plant organ. Based on a variety of self-sealing and self-healing processes in plants, different functional principles were transferred into bio-inspired self-repairing materials.[9][10][11]The connecting link between the biological model and the technical application is an abstraction describing the underlying functional principle of the biological model which can be for example an analytical model[12]or a numerical model. In cases where mainly physical-chemical processes are involved a transfer is especially promising. There is evidence in the academic literature[13]of thesebiomimeticdesign approaches being used in the development of self-healing systems for polymer composites.[14] The DIW[clarification needed]structure from above can be used to essentially mimic the structure of skin. Tooheyet al.did this with anepoxysubstrate containing a grid of microchannels containingdicyclopentadiene(DCPD), and incorporatedGrubbs' catalystto the surface. This showed partial recovery of toughness after fracture, and could be repeated several times because of the ability to replenish the channels after use. The process is not repeatable forever, because thepolymerin the crack plane from previous healings would build up over time.[15] Inspired by rapid self-sealing processes in the twining liana Aristolochia macrophylla and related species (pipevines) a biomimetic PU-foam coating for pneumatic structures was developed.[16]With respect to low coating weight and thickness of the foam layer maximum repair efficiencies of 99.9% and more have been obtained.[17][18][19]Other role models are latex bearing plants as the weeping fig (Ficus benjamina), the rubber tree (Hevea brasiliensis) and spurges (Euphorbia spp.), in which the coagulation of latex is involved in the sealing of lesions.[20][21][22]Different self-sealing strategies for elastomeric materials were developed showing significant mechanical restoration after a macroscopic lesion.[23][24]

Self-healing polymers and elastomers

edit

In the last century, polymers became a base material in everyday life for products like plastics, rubbers, films, fibres or paints. This huge demand has forced to extend their reliability and maximum lifetime, and a new design class of polymeric materials that are able to restore their functionality after damage or fatigue was envisaged. These polymer materials can be divided into two different groups based on the approach to the self-healing mechanism: intrinsic or extrinsic.[25][26] Autonomous self-healingpolymersfollow a three-step process very similar to that of a biological response. In the event of damage, the first response is triggering or actuation, which happens almost immediately after damage is sustained. The second response is transport of materials to the affected area, which also happens very quickly. The third response is the chemical repair process. This process differs depending on the type of healing mechanism that is in place (e.g.,polymerization,entanglement, reversible cross-linking). These materials can be classified according to three mechanisms (capsule-based, vascular-based, and intrinsic), which can be correlated chronologically through four generations.[27]While similar in some ways, these mechanisms differ in the ways that response is hidden or prevented until actual damage is sustained.

Polymer breakdown

edit

From a molecular perspective, traditional polymers yield to mechanical stress through cleavage ofsigma bonds.[28]While newer polymers can yield in other ways, traditional polymers typically yield throughhomolyticorheterolytic bond cleavage.The factors that determine how a polymer will yield include: type of stress, chemical properties inherent to the polymer, level and type ofsolvation,and temperature.[28] From amacromolecularperspective, stress induced damage at the molecular level leads to larger scale damage called microcracks.[29]A microcrack is formed where neighboring polymer chains have been damaged in close proximity, ultimately leading to the weakening of the fiber as a whole.[29]

Homolytic bond cleavage

edit
Scheme 1.Homolytic cleavage ofpoly(methyl methacrylate)(PMMA).

Polymers have been observed to undergo homolytic bond cleavage through the use ofradicalreporters such asDPPH(2,2-diphenyl-1-picrylhydrazyl) and PMNB (pentamethylnitrosobenzene.) When a bond is cleaved homolytically, two radical species are formed that can recombine to repair damage or can initiate other homolytic cleavages which can in turn lead to more damage.[28]

Heterolytic bond cleavage

edit
Scheme 2.Heterolytic cleavage ofpolyethylene glycol.

Polymers have also been observed to undergo heterolytic bond cleavage through isotope labeling experiments. When a bond is cleaved heterolytically,cationicandanionicspecies are formed that can in turn recombine to repair damage, can bequenchedby solvent, or can react destructively with nearby polymers.[28]

Reversible bond cleavage

edit

Certain polymers yield to mechanical stress in an atypical, reversible manner.[30]Diels-Alder-based polymers undergo a reversiblecycloaddition,where mechanical stress cleaves twosigma bondsin a retroDiels-Alderreaction. This stress results in additional pi-bonded electrons as opposed to radical or charged moieties.[2]

Supramolecular breakdown

edit

Supramolecularpolymersare composed of monomers that interactnon-covalently.[31]Common interactions includehydrogen bonds,[32]metalcoordination,andvan der Waals forces.[31]Mechanical stress in supramolecular polymers causes the disruption of these specific non-covalent interactions, leading to monomer separation and polymer breakdown.

Intrinsic polymer-based systems

edit

In intrinsic systems, the material is inherently able to restore its integrity. While extrinsic approaches are generally autonomous, intrinsic systems often require an external trigger for the healing to take place (such as thermo-mechanical, electrical, photo-stimuli, etc.). It is possible to distinguish among 5 main intrinsic self-healing strategies. The first one is based on reversible reactions, and the most widely used reaction scheme is based on Diels-Alder (DA) and retro-Diels-Alder (rDA) reactions.[33]Another strategy achieves the self-healing in thermoset matrices by incorporating meltable thermoplastic additives. A temperature trigger allows the redispertion of thermoplastic additives into cracks, giving rise to mechanical interlocking.[34]Polymer interlockings based on dynamic supramolecular bonds or ionomers represent a third and fourth scheme. The involved supramolecular interactions and ionomeric clusters are generally reversible and act as reversible cross-links, thus can equip polymers with self-healing ability.[35][36]Finally, an alternative method for achieving intrinsic self-healing is based on molecular diffusion.[37]

Reversible bond-based polymers

edit

Reversible systems are polymeric systems that can revert to the initial state whether it ismonomeric,oligomeric,or non-cross-linked. Since thepolymeris stable under normal condition, the reversible process usually requires an external stimulus for it to occur. For a reversible healing polymer, if the material is damaged by means such as heating and reverted to its constituents, it can be repaired or "healed" to itspolymerform by applying the original condition used to polymerize it.

Polymer systems based on covalent bond formation and breakage

edit
Diels-Alder and retro-Diels-Alder
edit

Among the examples of reversible healing polymers, theDiels-Alder(DA) reaction and its retro-Diels-Alder(RDA) analogue seems to be very promising due to its thermal reversibility. In general, themonomercontaining the functional groups such asfuranormaleimideform two carbon-carbon bonds in a specific manner and construct the polymer through DA reaction. This polymer, upon heating, breaks down to its original monomeric units via RDA reaction and then reforms thepolymerupon cooling or through any other conditions that were initially used to make the polymer. During the last few decades, two types of reversiblepolymershave been studied: (i) polymers where the pendant groups, such asfuranormaleimidegroups, cross-link through successive DA coupling reactions; (ii) polymers where the multifunctional monomers link to each other through successive DA coupling reactions.[30]

Cross-linked polymers
edit

In this type ofpolymer,the polymer forms through the cross linking of the pendant groups from the linearthermoplastics.For example, Saegusaet al.have shown the reversible cross-linking of modified poly(N-acetylethyleneimine)s containing eithermaleimideor furancarbonyl pendant moideties. The reaction is shown in Scheme 3. They mixed the two complementarypolymersto make a highlycross-linkedmaterial through DA reaction of furan and maleimide units at room temperature, as thecross-linkedpolymeris more thermodynamically stable than the individual starting materials. However, upon heating the polymer to 80 °C for two hours in apolarsolvent,twomonomerswere regenerated via RDA reaction, indicating the breaking ofpolymers.[38]This was possible because the heating energy provided enough energy to go over the energy barrier and results in the twomonomers.Cooling the two startingmonomers,or damagedpolymer,to room temperature for 7 days healed and reformed the polymer.

Scheme 3.Reversible polymer cross-linking viaDiels-Aldercycloadditionreaction between furan and maleimide.[38]

The reversible DA/RDA reaction is not limited to furan-meleimides basedpolymersas it is shown by the work of Schiraldiet al.They have shown the reversible cross-linking of polymers bearing pendentanthracenegroup with maleimides. However, the reversible reaction occurred only partially upon heating to 250 °C due to the competingdecompositionreaction.[39]

Polymerization of multifunctional monomers
edit

In these systems, the DA reaction takes place in the backbone itself to construct the polymer, not as a link. For polymerization and healing processes of a DA-step-growthfuran-maleimidebased polymer (3M4F) were demonstrated by subjecting it to heating/cooling cycles. Tris-maleimide (3M) and tetra-furan (4F) formed a polymer through DA reaction and, when heated to 120 °C, de-polymerized through RDA reaction, resulting in the starting materials. Subsequent heating to 90–120 °C and cooling to room temperature healed the polymer, partially restoring its mechanical properties through intervention.[33][40]The reaction is shown in Scheme 4.

Scheme 4.Reversible highly cross-linked furan-maleimide based polymer network.[33]
Thiol-based polymers
edit

The thiol-based polymers havedisulfide bondsthat can be reversibly cross-linked throughoxidationandreduction.Under reducing condition, thedisulfide(SS) bridges in the polymer breaks and results in monomers, however, under oxidizing condition, thethiols(SH) of each monomer forms thedisulfide bond,cross-linking the starting materials to form the polymer. Chujoet al.have shown thethiol-based reversible cross-linked polymer using poly(N-acetylethyleneimine). (Scheme 5)[41]

Scheme 5.Reversible polymer cross-linking by disulfide bridges.[41]
Poly(urea-urethane)
edit

A soft poly(urea-urethane) network uses the metathesis reaction in aromatic disulphides to provide room-temperature self-healing properties, without the need for external catalysts. This chemical reaction is naturally able to create covalent bonds at room temperature, allowing the polymer to autonomously heal without an external source of energy. Left to rest at room temperature, the material mended itself with 80 percent efficiency after only two hours and 97 percent after 24 hours.[citation needed] In 2014 a polyureaelastomer-based material was shown to be self-healing, melding together after being cut in half, without the addition of catalysts or other chemicals. The material also include inexpensive commercially available compounds. The elastomer molecules were tweaked, making the bonds between them longer. The resulting molecules are easier to pull apart from one another and better able to rebond at room temperature with almost the same strength. The rebonding can be repeated. Stretchy, self-healing paints and other coatings recently took a step closer to common use, thanks to research being conducted at the University of Illinois. Scientists there have used "off-the-shelf" components to create a polymer that melds back together after being cut in half, without the addition of catalysts or other chemicals.[42][43]

The urea-urethane polymers however have glassy transition temperatures below 273 K therefore at room temperature they are gels and their tensile strength is low.[43]To optimize the tensile strength the reversible bonding energy, or the polymer length must be increased to increase the degree of covalent or mechanical interlocking respectively. However, increase polymer length inhibits mobility and thereby impairs the ability for polymers to re-reversibly bond. Thus at each polymer length an optimal reversible bonding energy exists.[44]

Vitrimers
edit

Vitrimersare a subset of polymers that bridge the gap between thermoplastics and thermosets.[45][46]Their dependence on dissociative and associative exchange within dynamiccovalent adaptable networksallows for a variety of chemical systems to be accessed that allow for the synthesis of mechanically robust materials with the ability to be reprocessed many times while maintaining their structural properties and mechanical strength.[47]The self-healing aspect of these materials is due to the bond exchange of crosslinked species as a response to applied external stimuli, such as heat. Dissociative exchange is the process by which crosslinks are broken prior to recombination of crosslinking species, thereby recovering the crosslink density after exchange.[48]Examples of dissociative exchange include reversible pericyclic reactions, nucleophilic transalkylation, and aminal transamination. Associative exchange involves the substitution reaction with an existing crosslink and the retention of crosslinks throughout exchange.[48]Examples of associative exchange include transesterification, transamination of vinylogous urethanes,[49]imine exchange,[50]and transamination of diketoneamines.[48]Vitrimers possessing nanoscale morphology are being studied, through the use of block copolymer vitrimers in comparison to statistical copolymer analogues, to understand the effects of self-assembly on exchange rates, viscoelastic properties, and reprocessability.[51]Other than recycling, vitrimer materials show promise for applications in medicine, for example self-healable bioepoxy,[52]and applications in self-healing electronic screens.[53]While these polymeric systems are still in their infancy they serve to produce commercially relevant, recyclable materials in the coming future as long as more work is done to tailor these chemical systems to commercially relevant monomers and polymers, as well as develop better mechanical testing and understanding of material properties throughout the lifetime of these materials (i.e. post reprocess cycles).

Copolymers with van der Waals force

If perturbation of van der Waals forces upon mechanical damage is energetically unfavourable, interdigitated alternating or random copolymer motifs will self-heal to an energetically more favourable state without external intervention. This self-healing behavior occurs within a relatively narrow compositional range depended on a viscoelastic response that energetically favours self-recovery upon chain separation, owing to ‘key-and-lock’ associations of the neighbouring chains. In essence, van der Waals forces stabilize neighbouring copolymers, which is reflected in enhanced cohesive-energy density (CED) values. Urban etc. illustrates how induced dipole interactions for alternating or random poly(methyl methacrylate-alt-ran-n-butyl acrylate) (p(MMA-alt-ran-nBA)) copolymers owing to directional van der Waals forces may enhance the CED at equilibrium (CEDeq) of entangled and side-by-side copolymer chains.

[54] [55] [56]

Extrinsic polymer-based systems

edit

In extrinsic systems, the healing chemistries are separated from the surrounding polymer in microcapsules or vascular networks which, after material damage/cracking, release their content into the crack plane, reacting and allowing the restoration of material functionalities.[57] These systems can be further subdivided in several categories. While capsule-based polymers sequester the healing agents in little capsules that only release the agents if they are ruptured, vascular self-healing materials sequester the healing agent in capillary type hollow channels that can be interconnected one dimensionally, two dimensionally, or three dimensionally. After one of these capillaries is damaged, the network can be refilled by an outside source or another channel that was not damaged. Intrinsic self-healing materials do not have a sequestered healing agent but instead have a latent self-healing functionality that is triggered by damage or by an outside stimulus.[57]Extrinsic self-healing materials can achieve healing efficiencies over 100% even when the damage is large.[58]

Microcapsule healing

edit

Capsule-based systems have in common that healing agents are encapsulated into suitable microstructures that rupture upon crack formation and lead to a follow-up process in order to restore the materials' properties. If the walls of the capsule are created too thick, they may not fracture when the crack approaches, but if they are too thin, they may rupture prematurely.[59] In order for this process to happen at roomtemperature,and for the reactants to remain in a monomeric state within the capsule, acatalystis also imbedded into the thermoset. The catalyst lowers theenergy barrierof thereactionand allows the monomer to polymerize without the addition of heat. The capsules around the monomer are important to maintain separation until the crack facilitates the reaction.[30][60] In the capsule-catalyst system, the encapsulated healing agent is released into the polymer matrix and reacts with the catalyst, already present in the matrix.[61] There are many challenges in designing this type of material. First, the reactivity of thecatalystmust be maintained even after it is enclosed in wax. Additionally, the monomer must flow at a sufficient rate (have low enoughviscosity) to cover the entire crack before it is polymerized, or full healing capacity will not be reached. Finally, the catalyst must quickly dissolve into the monomer in order to react efficiently and prevent the crack from spreading further.[60]

Scheme 6.ROMP of DCPD viaGrubbs' catalyst

This process has been demonstrated withdicyclopentadiene(DCPD) andGrubbs' catalyst(benzylidene-bis(tricyclohexylphosphine)dichlororuthenium). Both DCPD andGrubbs' catalystare imbedded in anepoxyresin.Themonomeron its own is relatively unreactive andpolymerizationdoes not take place. When a microcrack reaches both the capsule containing DCPD and thecatalyst,themonomeris released from the core–shell microcapsule and comes in contact with exposed catalyst, upon which the monomer undergoesring opening metathesis polymerization(ROMP).[60]Themetathesisreaction of themonomerinvolves the severance of the two double bonds in favor of new bonds. The presence of thecatalystallows for theenergy barrier(energy of activation) to be lowered, and the polymerizationreactioncan proceed at room temperature.[62]The resultingpolymerallows theepoxycomposite materialto regain 67% of its former strength.

Grubbs' catalystis a good choice for this type of system because it is insensitive to air and water, thus robust enough to maintain reactivity within the material. Using a live catalyst is important to promote multiple healing actions.[63]The major drawback is the cost. It was shown that using more of the catalyst corresponded directly to higher degree of healing.Rutheniumis quite costly, which makes it impractical for commercial applications.

Figure 1.Depiction of crack propagation through microcapsule-imbedded material. Monomer microcapsules are represented by pink circles and catalyst is shown by purple dots.

In contrast, in multicapsule systems both the catalyst and the healing agent are encapsulated in different capsules.[64]In a third system, called latent functionality, a healing agent is encapsulated, that can react with the polymerizer component that is present in the matrix in the form of residual reactive functionalities.[60]In the last approach (phase separation), either the healing agent or the polymerizer is phase-separated in the matrix material.[65]

Vascular approaches

edit

The same strategies can be applied in 1D, 2D and 3D vascular based systems.[66][67][15]

Hollow tube approach

edit

For the first method, fragile glass capillaries or fibers are imbedded within acomposite material.(Note: this is already a commonly used practice for strengthening materials. SeeFiber-reinforced plastic.)[68]The resulting porous network is filled withmonomer.When damage occurs in the material from regular use, the tubes also crack and the monomer is released into the cracks. Other tubes containing a hardening agent also crack and mix with themonomer,causing the crack to be healed.[63]There are many things to take into account when introducing hollow tubes into acrystalline structure.First to consider is that the created channels may compromise the load bearing ability of the material due to the removal of load bearing material.[69]Also, the channel diameter, degree of branching, location of branch points, and channel orientation are some of the main things to consider when building up microchannels within a material. Materials that don't need to withstand much mechanicalstrain,but want self-healing properties, can introduce more microchannels than materials that are meant to be load bearing.[69]There are two types of hollow tubes: discrete channels, and interconnected channels.[69]

Discrete channels
edit

Discrete channels can be built independently of building the material and are placed in an array throughout the material.[69]When creating these microchannels, one major factor to take into account is that the closer the tubes are together, the lower the strength will be, but the more efficient the recovery will be.[69]A sandwich structure is a type of discrete channels that consists of tubes in the center of the material, and heals outwards from the middle.[70]The stiffness of sandwich structures is high, making it an attractive option forpressurizedchambers.[70]For the most part in sandwich structures, the strength of the material is maintained as compared to vascular networks. Also, material shows almost full recovery from damage.[70]

Interconnected networks
edit

Interconnected networks are moreefficientthan discrete channels, but are harder and more expensive to create.[69]The most basic way to create these channels is to apply basic machining principles to create micro scale channel grooves. These techniques yield channels from 600 to 700 micrometers.[69]This technique works great on the two-dimensional plane, but when trying to create a three-dimensional network, they are limited.[69]

Direct ink writing
edit

The Direct Ink Writing (DIW) technique is a controlled extrusion of viscoelastic inks to create three-dimensionalinterconnectednetworks.[69]It works by first settingorganicink in a defined pattern. Then the structure is infiltrated with a material like anepoxy.This epoxy is thensolidified,and the ink can be sucked out with a modest vacuum, creating the hollow tubes.[69]

Carbon nanotube networks
edit

Through dissolving a linearpolymerinside a solid three-dimensionalepoxymatrix, so that they are miscible to each other, the linear polymer becomes mobile at a certaintemperature[71]Whencarbon nanotubesare also incorporated into epoxy material, and adirect currentis run through the tubes, a significant shift in sensing curve indicates permanent damage to thepolymer,thus ‘sensing’ a crack.[72]When thecarbon nanotubessense a crack within thestructure,they can be used as thermal transports to heat up the matrix so the linearpolymerscan diffuse to fill the cracks in the epoxy matrix. Thus healing the material.[71]

SLIPS
edit

A different approach was suggested by Prof. J. Aizenberg from Harvard University, who suggested to useSlippery Liquid-Infused Porous Surfaces(SLIPS), a porous material inspired by the carnivorous pitcher plant and filled with a lubricating liquid immiscible with both water and oil.[73]SLIPS possess self-healing and self-lubricating properties as well as icephobicity and were successfully used for many purposes.

Sacrificial thread stitching
edit

Organic threads (such as polylactide filament for example) are stitched through laminate layers of fiber reinforced polymer, which are then boiled and vacuumed out of the material after curing of the polymer, leaving behind empty channels than can be filled with healing agents.[74]

Self-healing fibre-reinforced polymer composites

edit

Methods for the implementation of self-healing functionality into filled composites and fibre reinforced polymers (FRPs) are almost exclusively based on extrinsic systems and thus can be broadly classified into two approaches; discrete capsule-based systems and continuous vascular systems. In contrast to non-filled polymers, the success of an intrinsic approach based on bond reversibility has yet to be proven in FRPs. To date, self-healing of FRPs has mostly been applied to simple structures such as flat plates and panels. There is however a somewhat limited application of self-healing in flat panels, as access to the panel surface is relatively simple and repair methods are very well established in industry. Instead, there has been a strong focus on implementing self-healing in more complex and industrially relevant structures such as T-Joints[75][76]and Aircraft Fuselages.[77]

Capsule-based systems

edit

The creation of a capsule-based system was first reported by White et al. in 2001,[59]and this approach has since been adapted by a number of authors for introduction into fibre reinforced materials.[78][79][80]This method relies on the release of an encapsulated healing agent into the damage zone, and is generally a once off process as the functionality of the encapsulated healing agent cannot be restored. Even so, implemented systems are able to restore material integrity to almost 100% and remain stable over the material lifetime.

Vascular systems

edit

A vascular or fibre-based approach may be more appropriate for self-healing impact damage in fibre-reinforced polymer composite materials. In this method, a network of hollow channels known as vascules, similar to the blood vessels within human tissue, are placed within the structure and used for the introduction of a healing agent. During a damage event cracks propagate through the material and into the vascules causing them to be cleaved open. A liquid resin is then passed through the vascules and into the damage plane, allowing the cracks to be repaired. Vascular systems have a number of advantages over microcapsule based systems, such as the ability to continuously deliver large volumes of repair agents and the potential to be used for repeated healing. The hollow channels themselves can also be used for additional functionality, such as thermal management and structural health monitoring.[81]A number of methods have been proposed for the introduction of these vascules, including the use of hollow glass fibres (HGFs),[82] [83]3D printing,[15]a "lost wax" process[84][85]and a solid preform route.[86]

Self-healing coatings

edit

Coatings allow the retention and improvement of bulk properties of a material. They can provide protection for a substrate from environmental exposure. Thus, when damage occurs (often in the form of microcracks), environmental elements like water and oxygen can diffuse through the coating and may cause material damage or failure. Microcracking in coatings can result in mechanical degradation or delamination of the coating, or in electrical failure in fibre-reinforced composites and microelectronics, respectively. As the damage is on such a small scale, repair, if possible, is often difficult and costly. Therefore, a coating that can automatically heal itself ( “self-healing coating” ) could prove beneficial by automatic recovering properties (such as mechanical, electrical and aesthetic properties), and thus extending the lifetime of the coating. The majority of the approaches that are described in literature regarding self-healing materials can be applied to make “self-healing” coatings, including microencapsulation[87][59]and the introduction of reversible physical bonds such as hydrogen bonding,[88]ionomers [89][90]and chemical bonds (Diels-Alder chemistry).[91]Microencapsulation is the most common method to develop self-healing coatings. The capsule approach originally described by White et al., using microencapsulated dicyclopentadiene (DCPD) monomer and Grubbs' catalyst to self-heal epoxy polymer[59]was later adapted to epoxy adhesive films that are commonly used in the aerospace and automotive industries for bonding metallic and composite substrates.[92]Recently, microencapsulated liquid suspensions of metal or carbon black were used to restore electrical conductivity in a multilayer microelectronic device and battery electrodes respectively;[93][94]however the use of microencapsulation for restoration of electrical properties in coatings is limited. Liquid metal microdroplets have also been suspended within silicone elastomer to create stretchable electrical conductors that maintain electrical conductivity when damaged, mimicking the resilience of soft biological tissue.[95]The most common application of this technique is proven in polymer coatings for corrosion protection. Corrosion protection of metallic materials is of significant importance on an economical and ecological scale. To prove the effectiveness of microcapsules in polymer coatings for corrosion protection, researchers have encapsulated a number of materials. These materials include isocyanates[96][97]monomers such as DCPD[61][79]GMA[98]epoxy resin,[99]linseed oil[100][101]and tung oil.,[102]and drugs. By using the aforementioned materials for self healing in coatings, it was proven that microencapsulation effectively protects the metal against corrosion and extends the lifetime of a coating.

Coatings in high temperature applications may be designed to exhibit self-healing performance through the formation of a glass. In such situations, such ashigh emissivity coatings,the viscosity of the glass formed determines the self healing ability of the coating, which may compete with defect formation due to oxidation orablation.[103]Silicate glass based self-healing materials are of particular value inthermal barriercoatings and towards space applications such as heat shields. Composite materials based onMolybdenum disilicideare the subject of various studies towards enhancing their glass-based self healing performance in coating applications.[104]

Self-healing cementitious materials

edit

Cementitious materials have existed since the Roman era. These materials have a natural ability to self-heal, which was first reported by the French Academy of Science in 1836.[105]This ability can be improved by the integration of chemical and biochemical strategies.

Autogenous healing

edit

Autogenous healing is the natural ability of cementitious materials to repair cracks. This ability is principally attributed to further hydration of unhydrated cement particles and carbonation of dissolved calcium hydroxide.[105]Cementitious materials in fresh-water systems can autogenously heal cracks up to 0.2 mm over a period of 7 weeks.[106]

In order to promote autogenous healing and to close wider cracks, superabsorbent polymers can be added to a cementitious mixture.[107][108]Addition of 1 m% of selected superabsorbent polymer versus cement to a cementitious material, stimulated further hydration with nearly 40% in comparison with a traditional cementitious material, if 1 h water contact per day was allowed.[109]

Chemical additives based healing

edit

Self-healing of cementitious materials can be achieved through the reaction of certain chemical agents. Two main strategies exist for housing these agents, namely capsules and vascular tubes. These capsules and vascular tubes, once ruptured, release these agents and heal the crack damage. Studies have mainly focused on improving the quality of these housings and encapsulated materials in this field.[110]

Bio-based healing

edit

According to a 1996 study by H. L. Erlich inChemical Geologyjournal, the self-healing ability of concrete has been improved by the incorporation of bacteria, which can induce calcium carbonate precipitation through their metabolic activity.[111]These precipitates can build up and form an effective seal against crack related water ingress. At the First International Conference on Self Healing Materials held in April, 2007 in The Netherlands, Henk M. Jonkers and Erik Schlangen presented their research in which they had successfully used the "alkaliphilic spore-forming bacteria" as a "self-healing agent in concrete".[112][113]They were the first to incorporate bacteria within cement paste for the development of self-healing concrete.[114]It was found that the bacteria directly added to the paste only remained viable for 4 months. Later studies saw Jonkers use expanded clay particles[115]and Van Tittlelboom use glass tubes,[116]to protect the bacteria inside the concrete. Other strategies to protect the bacteria have also since been reported.[117]

Self-healing ceramics

edit

Generally, ceramics are superior in strength to metals at high temperatures, however, they are brittle and sensitive to flaws, and this brings into question their integrity and reliability as structural materials.[118] phase ceramics, also known asMAX Phases,can autonomously heal crack damage by an intrinsic healing mechanism. Micro cracks caused by wear or thermal stress are filled with oxides formed from the MAX phase constituents, commonly the A-element, during high temperature exposure to air.[119] Crack gap filling was first demonstrated for Ti3AlC2by oxidation at 1200 °C in air.[120]Ti2AlC and Cr2AlC have also demonstrated said ability, and more ternary carbides and nitrides are expected to be able to autonomously self-heal.[121]The process is repeatable up to the point of element depletion, distinguishing MAX phases from other self-healing materials that require external healing agents (extrinsic healing) for single crack gap filling. Depending on the filling-oxide, improvement of the initial properties such as local strength can be achieved.[122] On the other hand, mullite, alumina and zirconia do not have the ability to heal intrinsically, but could be endowed with self-healing capabilities by embedding second phase components into the matrix. Upon cracking, these particles are exposed to oxygen, and in the presence of heat, they react to form new materials which fill the crack gap under volume expansion.[123] This concept has been proven using SiC to heal cracks in an Alumina matrix,[124]and further studies have investigated the high temperature strength,[125]and the static and cyclic fatigue strength of the healed part.[126]The strength and bonding between the matrix and the healing agent are of prime importance and thus govern the selection of the healing particles.

Self-healing metals

edit

When exposed for long times to high temperatures and moderate stresses, metals exhibit premature and low-ductility creep fracture, arising from the formation and growth of cavities. Those defects coalesce into cracks which ultimately cause macroscopic failure. Self-healing of early stage damage is thus a promising new approach to extend the lifetime of the metallic components. In metals, self-healing is intrinsically more difficult to achieve than in most other material classes, due to their high melting point and, as a result, low atom mobility. Generally, defects in the metals are healed by the formation of precipitates at the defect sites that immobilize further crack growth. Improved creep and fatigue properties have been reported for underaged aluminium alloys compared to the peak hardening Al alloys, which is due to the heterogeneous precipitation at the crack tip and its plastic zone.[127]The first attempts to heal creep damage in steels were focused on the dynamic precipitation of either Cu or BN at the creep-cavity surface.[128][129]Cu precipitation has only a weak preference for deformation-induced defects as a large fraction of spherical Cu precipitates is simultaneously formed with the matrix.[130][131] Recently, gold atoms were recognized as a highly efficient healing agents in Fe-based alloys. A defect-induced mechanism is indicated for the Au precipitation, i.e. the Au solute remains dissolved until defects are formed.[132]Autonomous repair of high-temperature creep damage was reported by alloying with a small amount of Au. Healing agents selectively precipitate at the free surface of a creep cavity, resulting in pore filling. For the lower stress levels up to 80% filling of the creep cavities with Au precipitates is achieved[133]resulting in a substantial increase in creep life time. Work to translate the concept of creep damage healing in simple binary or ternary model systems to real multicomponent creep steels is ongoing.

In 2023 theSandia National Laboratoriesreported the finding of self-healing of fatigue cracks in metal[134][135]and reported that the observations seems to confirm a 2013 study predicting the effect.[136]

Self-healing hydrogels

edit

Hydrogelsaresoft solidsconsisting of a three dimensional network of natural or synthetic polymers with a high water content. Hydrogels based onnon-covalent interactionsordynamic covalent chemistrycan exhibit self-healing properties after cutting or breaking.[137]Hydrogels that can fully fluidize followed by self-healing are of particular interest inbiomedical engineeringfor the development of injectable hydrogels for tissue regeneration or3D bioprintinginks.[138]

Self-healing organic dyes

edit

Recently, several classes of organic dyes were discovered that self-heal afterphoto-degradationwhen doped inPMMAand other polymer matrices.[139]This is also known as reversiblephoto-degradation.It was shown that, unlike common process like molecular diffusion,[140]the mechanism is caused by dye-polymer interaction.[141]

Self-healing of ice

edit

It has recently been shown that micrometer-sized defects in a pristine layer of ice heal spontaneously within a matter of several hours. The generated curvature by any defect causes a local increased vapor pressure and therefore enhances the volatility of the surface molecules. Hence, the mobility of the upper layer of water molecules increases significantly. The main mechanism, that dominates this healing effect is therefore sublimation from, and condensation onto the surface.[142]This opposes earlier work that describes sintering of ice spheres by surface diffusion.[143]

Measurement of a self-healing scratch with an initial depth of approximately 2.5 micrometer, induced in a pristine ice layer of 247 Kelvin. Total healing time: 205 minutes.[142]

Further applications

edit

Self-healing epoxies can be incorporated onto metals in order to prevent corrosion. A substrate metal showed major degradation and rust formation after 72 hours of exposure. But after being coated with the self-healing epoxy, there was no visible damage under SEM after 72 hours of the same exposure.[144]

Assessment of self-healing efficacy

edit

Numerous methodologies for the assessment of self-healing capabilities have been developed for each material class (Table 1).

Table 1. Damaging methods for self-healing assessment of different classes of material.
Material class Damage mechanism Healing
Polymers Razor blade/scalpel cut; Tensile test with rupture; Ballistic impact Autonomic healing supramolecular networks
Polymers Razor blade/scalpel cut Temperature triggered supramolecular networks
Fibre Reinforced Composite Delamination BVID (Barely Visible Impact Damage) Vascular self-healing; Microcapsule self-healing
Coatings Microcutting with corrosion; Corrosion/erosion; Pull-out tests (adhesion); Microscratching Molecular inter-diffusion (solvent); Encapsulated agent
Concrete Crack initiation by bending compression Activation of microencapsulated agent
Ceramic Crack initiation by indentation Temperature triggered oxidation reaction
Ceramic coating Crack initiation by indentation Temperature triggered oxidation reaction
Polyurethane foam coating Puncturing with a spike Reduction of the effective leakage area by negative strains pushing the walls of the fissure in the foam coatings to one another.[17]

Hence, when self-healing is assessed, different parameters need to be considered: type of stimulus (if any), healing time, maximum amount of healing cycles the material can tolerate, and degree of recovery, all whilst considering the material's virgin properties.[145][146][88] This typically takes account of relevant physical parameters such as tensile modulus, elongation at break, fatigue-resistance, barrier properties, colour and transparency. The self-healing ability of a given material generally refers to the recovery of a specific property relative to the virgin material, designated as the self-healing efficiency. The self-healing efficiency can be quantified by comparing the respective experimental value obtained for the undamaged virgin sample (fvirgin) with the healed sample (fhealed) (eq.1)[147]

In a variation of this definition that is relevant to extrinsic self-healing materials, the healing efficiency takes into consideration the modification of properties caused by introducing the healing agent. Accordingly, the healed sample property is compared to that of an undamaged control equipped with self-healing agent fnon-healed(equation2).

For a certain property Pi of a specific material, an optimal self-healing mechanism and process is characterized by the full restoration of the respective material property after a suitable, normalized damaging process. For a material where 3 different properties are assessed, it should be determined 3 efficiencies given asƞ1(P1),ƞ2(P2) andƞ3(P3). The final average efficiency based on a number n of properties for a self-healing material is accordingly determined as the harmonic mean given by equation3.The harmonic mean is more appropriate than the traditional arithmetic mean, as it is less sensitive to large outliers.

Commercialization

edit

At least two companies are attempting to bring the newer applications of self-healing materials to the market.Arkema,a leading chemicals company, announced in 2009 the beginning of industrial production of self-healing elastomers.[148]As of 2012, Autonomic Materials Inc., had raised over three million US dollars.[149][150]

References

edit
  1. ^abGhosh SK (2008).Self-healing materials: fundamentals, design Strategies, and applications(1st ed.). Weinheim: Wiley – VCH. p. 145.ISBN978-3-527-31829-2.
  2. ^abYuan YC, Yin T, Rong MZ, Zhang MQ (2008)."Self healing in polymers and polymer composites. Concepts, realization and outlook: A review".Express Polymer Letters.2(4):238–50.doi:10.3144/expresspolymlett.2008.29.
  3. ^abWayman E (November 16, 2011)."The Secrets of Ancient Rome's Buildings".Smithsonian.Retrieved13 November2016.
  4. ^"Back to the Future with Roman Architectural Concrete".Lawrence Berkeley National Laboratory.University of California. December 15, 2014.Retrieved17 November2016.
  5. ^Hartnett K (December 19, 2014)."Why is ancient Roman concrete still standing?".Boston Globe.Retrieved17 November2016.
  6. ^Jackson MD, Landis EN, Brune PF, Vitti M, Chen H, Li Q, et al. (December 2014)."Mechanical resilience and cementitious processes in Imperial Roman architectural mortar".Proceedings of the National Academy of Sciences of the United States of America.111(52):18484–89.Bibcode:2014PNAS..11118484J.doi:10.1073/pnas.1417456111.PMC4284584.PMID25512521.
  7. ^"First international conference on self-healing materials".Delft University of Technology.12 April 2007.Retrieved19 May2013.
  8. ^ Nosonovsky M, Rohatgi P (2011).Biomimetics in Materials Science: Self-healing, self-lubricating, and self-cleaning materials.Springer Series in Materials Science. Vol. 152. Springer.ISBN978-1-4614-0925-0.
  9. ^Speck T, Mülhaupt R, Speck O (2013). "Self-healing in plants as bio-inspiration for self-repairing polymers". In Binder W (ed.).Self-Healing Polymers.Wiley-VCH. pp.61–89.doi:10.1002/9783527670185.ch2.ISBN978-3-527-33439-1.
  10. ^Speck O, Schlechtendahl M, Borm F, Kampowski T, Speck T (2013). "Bio-inspired self-healing materials". In Fratzl P, Dunlop JW, Weinkamer R (eds.).Materials Design Inspired by Nature: Function through Inner Architecture.RSC Smart Materials. Vol. 4. The Royal Chemical Society. pp.359–89.
  11. ^Speck O, Luchsinger R, Rampf M, Speck T (2014). "Selbstreparatur in Natur und Technik. – Konstruktion": 9,72–75, 82.{{cite journal}}:Cite journal requires|journal=(help)
  12. ^Konrad W, Flues F, Schmich F, Speck T, Speck O (November 2013). "An analytic model of the self-sealing mechanism of the succulent plant Delosperma cooperi".Journal of Theoretical Biology.336:96–109.Bibcode:2013JThBi.336...96K.doi:10.1016/j.jtbi.2013.07.013.PMID23907028.
  13. ^Trask RS, Williams HR, Bond IP (March 2007). "Self-healing polymer composites: mimicking nature to enhance performance".Bioinspiration & Biomimetics.2(1):P1 –P9.Bibcode:2007BiBi....2....1T.doi:10.1088/1748-3182/2/1/P01.PMID17671320.S2CID22590061.
  14. ^"Genesys Reflexive (Self-Healing) Composites".Cornerstone Research Group. Archived fromthe originalon 2012-07-20.Retrieved2009-10-02.
  15. ^abcToohey KS, Sottos NR, Lewis JA, Moore JS, White SR (August 2007)."Self-healing materials with microvascular networks"(PDF).Nature Materials.6(8):581–85.Bibcode:2007NatMa...6..581T.doi:10.1038/nmat1934.PMID17558429.
  16. ^Busch S, Seidel R, Speck O, Speck T (July 2010)."Morphological aspects of self-repair of lesions caused by internal growth stresses in stems of Aristolochia macrophylla and Aristolochia ringens".Proceedings. Biological Sciences.277(1691):2113–20.doi:10.1098/rspb.2010.0075.PMC2880149.PMID20236971.
  17. ^abRampf M, Speck O, Speck T, Luchsinger RH (2013). "Investigation of a fast mechanical self-repair mechanism for inflatable structures".International Journal of Engineering Science.63:61–70.doi:10.1016/j.ijengsci.2012.11.002.
  18. ^Rampf M, Speck O, Speck T, Luchsinger RH (2012). "Structural and mechanical properties of flexible polyurethane foams cured under pressure".Journal of Cellular Plastics.48:49–65.doi:10.1177/0021955X11429171.S2CID136555131.
  19. ^Rampf M, Speck O, Speck T, Luchsinger RH (2011). "Self-repairing membranes for inflatable structures inspired by a rapid wound sealing process of climbing plants".Journal of Bionic Engineering.8(3):242–50.doi:10.1016/S1672-6529(11)60028-0.S2CID137853348.
  20. ^Bauer G, Speck T (March 2012)."Restoration of tensile strength in bark samples of Ficus benjamina due to coagulation of latex during fast self-healing of fissures".Annals of Botany.109(4):807–11.doi:10.1093/aob/mcr307.PMC3286277.PMID22207613.
  21. ^Bauer G, Friedrich C, Gillig C, Vollrath F, Speck T, Holland C (January 2014)."Investigating the rheological properties of native plant latex".Journal of the Royal Society, Interface.11(90): 20130847.doi:10.1098/rsif.2013.0847.PMC3836322.PMID24173604.
  22. ^Bauer G, Gorb SN, Klein MC, Nellesen A, von Tapavicza M, Speck T (2014)."Comparative study on plant latex particles and latex coagulation in Ficus benjamina, Campanula glomerata and three Euphorbia species".PLOS ONE.9(11): e113336.Bibcode:2014PLoSO...9k3336B.doi:10.1371/journal.pone.0113336.PMC4237448.PMID25409036.
  23. ^Nellesen A, Von Tapavicza M, Bertling J, Schmidt AM, Bauer G, Speck T (2011). "Pflanzliche Selbstheilung als Vorbild für selbstreparierende Elastomerwerkstoffe, GAK – Gummi, Fasern, Kunststoffe" [Self-healing in plants as a model for self-repairing elastomer materials].International Polymer Science and Technology.64(8):472–75.
  24. ^Schüssele AC, Nübling F, Thomann Y, Carstensen O, Bauer G, Speck T, Mülhaupt R (2012). "Self-healing rubbers based on NBR blends with hyperbranched polyethylenimines".Macromolecular Materials and Engineering.9(5):411–19.doi:10.1002/mame.201100162.
  25. ^Yang Y, Urban MW (September 2013). "Self-healing polymeric materials".Chemical Society Reviews.42(17):7446–67.doi:10.1039/c3cs60109a.PMID23864042.
  26. ^Mahajan, Mahendra S.; Gite, Vikas V. (2019). "Microcapsule-Assisted Smart Coatings". In Mishra, Munmaya K. (ed.).Applications of Encapsulation and Controlled Release(1st ed.). CRC Press. p. 249.doi:10.1201/9780429299520.ISBN9780429299520.S2CID210524952.
  27. ^Utrera-Barrios, Saul; Verdejo, Raquel; López-Manchado, Miguel A.; Hernández Santana, Marianella (2020)."Evolution of self-healing elastomers, from extrinsic to combined intrinsic mechanisms: a review".Materials Horizons.7(11):2882–2902.doi:10.1039/D0MH00535E.hdl:10261/342241.
  28. ^abcdCaruso MM, Davis DA, Shen Q, Odom SA, Sottos NR, White SR, Moore JS (November 2009). "Mechanically-induced chemical changes in polymeric materials".Chemical Reviews.109(11):5755–98.doi:10.1021/cr9001353.PMID19827748.
  29. ^abHayes SA, Zhang W, Branthwaite M, Jones FR (April 2007)."Self-healing of damage in fibre-reinforced polymer-matrix composites".Journal of the Royal Society, Interface.4(13):381–87.doi:10.1098/rsif.2006.0209.PMC2359850.PMID17311783.
  30. ^abcBergman SD, Wudl F (2008). "Mendable Polymers".Journal of Materials Chemistry.18:41–62.doi:10.1039/b713953p.
  31. ^abArmstrong G, Buggy M (2005). "Hydrogen-bonded supramolecules polymers: A literature review".Journal of Materials Science.40(3):547–59.Bibcode:2005JMatS..40..547A.doi:10.1007/s10853-005-6288-7.S2CID137424325.
  32. ^Utrera-Barrios, Saul; Hernández Santana, Marianella; Verdejo, Raquel; López-Manchado, Miguel A. (17 January 2020)."Design of Rubber Composites with Autonomous Self-Healing Capability".ACS Omega.5(4):1902–10.doi:10.1021/acs Omega.9b03516.PMC7003207.PMID32039326.
  33. ^abcChen X, Dam MA, Ono K, Mal A, Shen H, Nutt SR, et al. (March 2002). "A thermally re-mendable cross-linked polymeric material".Science.295(5560):1698–702.Bibcode:2002Sci...295.1698C.doi:10.1126/science.1065879.PMID11872836.S2CID31722523.
  34. ^Luo X, Ou R, Eberly DE, Singhal A, Viratyaporn W, Mather PT (March 2009). "A thermoplastic/thermoset blend exhibiting thermal mending and reversible adhesion".ACS Applied Materials & Interfaces.1(3):612–20.doi:10.1021/am8001605.PMID20355983.
  35. ^Cordier P, Tournilhac F, Soulié-Ziakovic C, Leibler L (February 2008). "Self-healing and thermoreversible rubber from supramolecular assembly".Nature.451(7181):977–80.Bibcode:2008Natur.451..977C.doi:10.1038/nature06669.PMID18288191.S2CID205212362.
  36. ^Kalista Jr SJ, Ward TC, Oyetunji Z (2007). "Self-Healing of Poly(Ethylene-co-Methacrylic Acid) Copolymers Following Projectile Puncture".Mechanics of Advanced Materials and Structures.14(5):391–97.doi:10.1080/15376490701298819.S2CID138047053.
  37. ^Yamaguchi M, Ono S, Okamoto K (2009). "Interdiffusion of dangling chains in weak gel and its application to self-repairing material".Mater. Sci. Eng. B.162(3):189–94.doi:10.1016/j.mseb.2009.04.006.
  38. ^abChujo Y, Sada K, Saegusa T (1990). "Reversible Gelation of Polyoxazoline by Means of Diels-Alder Reaction".Macromolecules.23(10):2636–41.Bibcode:1990MaMol..23.2636C.doi:10.1021/ma00212a007.
  39. ^Schiraldi DA, Liotta CL, Collard DM, Schiraldi DA (1999). "Cross-Linking and Modification of Poly(ethylene terephthalate-co-2,6-anthracenedicarboxylate) by Diels−Alder Reactions with Maleimides".Macromolecules.32(18):5786–92.Bibcode:1999MaMol..32.5786J.doi:10.1021/ma990638z.
  40. ^Weizman H, Nielsen C, Weizman OS, Nemat-Nasser S (2011). "Synthesis of a Self-Healing Polymer Based on Reversible Diels–Alder Reaction: An Advanced Undergraduate Laboratory at the Interface of Organic Chemistry and Materials Science".Journal of Chemical Education.88(8):1137–40.Bibcode:2011JChEd..88.1137W.doi:10.1021/ed101109f.
  41. ^abSaegusa T, Sada K, Naka A, Nomura R, Saegusa T (1993). "Synthesis and redox gelation of disulfide-modified polyoxazoline".Macromolecules.26(5):883–87.Bibcode:1993MaMol..26..883C.doi:10.1021/ma00057a001.
  42. ^Green R (2014-02-15)."Scientists create an inexpensive self-healing polymer".Gizmag.Retrieved2014-02-26.
  43. ^abYing H, Zhang Y, Cheng J (2014)."Dynamic urea bond for the design of reversible and self-healing polymers".Nature Communications.5:3218.Bibcode:2014NatCo...5.3218Y.doi:10.1038/ncomms4218.PMC4438999.PMID24492620.
  44. ^Madden I, Luijten E (2017-03-14)."Molecular dynamics of reversible self-healing materials".Bulletin of the American Physical Society.62(4): H18.002.Bibcode:2017APS..MARH18002M.
  45. ^Capelot M, Unterlass MM, Tournilhac F, Leibler L (2012-07-17). "Catalytic Control of the Vitrimer Glass Transition".ACS Macro Letters.1(7):789–92.doi:10.1021/mz300239f.ISSN2161-1653.PMID35607118.
  46. ^Fortman DJ, Brutman JP, Cramer CJ, Hillmyer MA, Dichtel WR (November 2015)."Mechanically activated, catalyst-free polyhydroxyurethane vitrimers".Journal of the American Chemical Society.137(44):14019–22.Bibcode:2015JAChS.13714019F.doi:10.1021/jacs.5b08084.PMID26495769.
  47. ^Denissen W, Winne JM, Du Prez FE (January 2016)."Vitrimers: permanent organic networks with glass-like fluidity".Chemical Science.7(1):30–38.doi:10.1039/C5SC02223A.PMC5508697.PMID28757995.
  48. ^abcScheutz GM, Lessard JJ, Sims MB, Sumerlin BS (October 2019). "Adaptable Crosslinks in Polymeric Materials: Resolving the Intersection of Thermoplastics and Thermosets".Journal of the American Chemical Society.141(41):16181–96.Bibcode:2019JAChS.14116181S.doi:10.1021/jacs.9b07922.PMID31525287.S2CID202642134.
  49. ^Lessard JJ, Garcia LF, Easterling CP, Sims MB, Bentz KC, Arencibia S, Savin DA, Sumerlin BS (2019-02-20). "Catalyst-Free Vitrimers from Vinyl Polymers".Macromolecules.52(5):2105–11.Bibcode:2019MaMol..52.2105L.doi:10.1021/acs.macromol.8b02477.ISSN0024-9297.S2CID104386610.
  50. ^Schoustra, Sybren K.; Dijksman, Joshua A.; Zuilhof, Han; Smulders, Maarten M. J. (2021)."Molecular control over vitrimer-like mechanics – tuneable dynamic motifs based on the Hammett equation in polyimine materials".Chemical Science.12(1):293–302.doi:10.1039/D0SC05458E.PMC8178953.PMID34163597.
  51. ^Lessard JJ, Scheutz GM, Sung SH, Lantz KA, Epps Iii TH, Sumerlin BS (December 2019). "Block Copolymer Vitrimers".Journal of the American Chemical Society.142(1):283–89.doi:10.1021/jacs.9b10360.PMID31794219.S2CID208627400.
  52. ^Liu T, Hao C, Zhang S, Yang X, Wang L, Han J, Li Y, Xin J, Zhang J (2018-08-14). "A Self-Healable High Glass Transition Temperature Bioepoxy Material Based on Vitrimer Chemistry".Macromolecules.51(15):5577–85.Bibcode:2018MaMol..51.5577L.doi:10.1021/acs.macromol.8b01010.ISSN0024-9297.S2CID105448238.
  53. ^Monks K, Stewart A (25 June 2015)."Self-healing plastic promises unbreakable phones".CNN.Retrieved2019-12-06.
  54. ^Urban, M. W. et al. Key-and-lock commodity self-healing copolymers. Science 362, 220–225 (2018).
  55. ^Marek Urban, Siyang Wang, Self-healing copolymers via van der Waals interactions, Composites at Lake Louise (2019).
  56. ^Ying Yang, Dmitriy Davydovich, Chris C. Hornat, Xiaolin Liu, Marek W. Urban, Leaf-Inspired Self-Healing Polymers, Chem, Volume 4, 1928-1936 (2018).
  57. ^abBlaiszik BJ, Kramer SL, Olugebefola SC, Moore JS, Sottos NR, White SR (2010). "Self-Healing Polymers and Composites".Annual Review of Materials Research.40(1):179–211.Bibcode:2010AnRMS..40..179B.doi:10.1146/annurev-matsci-070909-104532.ISSN1531-7331.
  58. ^Wang Y, Pham DT, Ji C (2015-12-31)."Self-healing composites: A review".Cogent Engineering.2(1): 1075686.doi:10.1080/23311916.2015.1075686.
  59. ^abcdWhite SR, Sottos NR, Geubelle PH, Moore JS, Kessler MR, Sriram SR, et al. (February 2001). "Autonomic healing of polymer composites".Nature.409(6822):794–97.Bibcode:2001Natur.409..794W.doi:10.1038/35057232.PMID11236987.S2CID11334883.
  60. ^abcdWhite SR, Delafuente DA, Ho V, Sottos NR, Moore JS, White SR (2007). "Solvent-Promoted Self-Healing in Epoxy Materials".Macromolecules.40(25):8830–32.Bibcode:2007MaMol..40.8830C.CiteSeerX10.1.1.494.785.doi:10.1021/ma701992z.
  61. ^abBrown EN, Sottos NR, White SR (2002). "Fracture testing of a self-healing polymer composite".Experimental Mechanics.42(4):372–79.doi:10.1007/BF02412141.hdl:2142/265.S2CID189768207.
  62. ^Grubbs RH, Tumas W (February 1989). "Polymer synthesis and organotransition metal chemistry".Science.243(4893):907–15.Bibcode:1989Sci...243..907G.doi:10.1126/science.2645643.PMID2645643.
  63. ^abPang JW, Bond IP (2005). "A Hollow Fibre Reinforced Polymer Composite Encompassing Self-Healing and Enhanced Damage Visibility".Composite Science and Technology.65(11–12):1791–99.CiteSeerX10.1.1.552.4996.doi:10.1016/j pscitech.2005.03.008.
  64. ^Keller MW, White SR, Sottos NR (2007). "A self-healing poly(dimethyl siloxane) elastomer".Adv. Funct. Mater.17(14):2399–404.Bibcode:2007PhDT........81K.doi:10.1002/adfm.200700086.S2CID15444050.
  65. ^Cho SH, Andersson HM, White SR, Sottos NR, Braun PV (2006). "Polydimethylsiloxane-Based Self-Healing Materials".Adv. Mater.18(8):997–1000.Bibcode:2006AdM....18..997C.doi:10.1002/adma.200501814.S2CID1175489.
  66. ^Dry CM, Sottos NR (1993). Varadan VK (ed.). "Passive smart self-repair in polymer matrix composite materials".Smart Structures and Materials 1993: Smart Materials.SPIE Proc. (1916):438–44.Bibcode:1993SPIE.1916..438D.doi:10.1117/12.148501.S2CID136696600.
  67. ^Wang KM,Lorente S,Bejan A(2006). "Vascularized networks with two optimized channel sizes".J. Phys. D: Appl. Phys.39(14):3086–96.Bibcode:2006JPhD...39.3086W.doi:10.1088/0022-3727/39/14/031.S2CID120304072.
  68. ^Dry C (1996). "Procedures Developed for Self-Repair of Polymer Matrix Composite Materials".Composite Structure.35(3):263–64.doi:10.1016/0263-8223(96)00033-5.
  69. ^abcdefghijOlugebefola SC, Aragón AM, Hansen CJ, Hamilton AR, Kozola BD, Wu W, et al. (2010). "Polymer Microvascular Network Composites".Journal of Composite Materials.44(22):2587–603.Bibcode:2010JCoMa..44.2587O.doi:10.1177/0021998310371537.ISSN0021-9983.S2CID14499195.
  70. ^abcWilliams HR, Trask RS, Bond IP (2007). "Self-healing composite sandwich structures".Smart Materials and Structures.16(4):1198–207.Bibcode:2007SMaS...16.1198W.doi:10.1088/0964-1726/16/4/031.ISSN0964-1726.S2CID136923522.
  71. ^abHayes SA, Jones FR, Marshiya K, Zhang W (2007). "A self-healing thermosetting composite material".Composites Part A: Applied Science and Manufacturing.38(4):1116–20.doi:10.1016/j positesa.2006.06.008.ISSN1359-835X.
  72. ^Thostenson ET, Chou TW (2006). "Carbon Nanotube Networks: Sensing of Distributed Strain and Damage for Life Prediction and Self Healing".Advanced Materials.18(21):2837–41.Bibcode:2006AdM....18.2837T.doi:10.1002/adma.200600977.ISSN0935-9648.S2CID137693495.
  73. ^Nosonovsky M (September 2011)."Materials science: slippery when wetted".Nature.477(7365):412–13.Bibcode:2011Natur.477..412N.doi:10.1038/477412a.PMID21938059.S2CID205067351.
  74. ^"Repeated Self-Healing Now Possible in Composite Materials".Beckman Institute.Retrieved17 November2016.
  75. ^Yang T, Zhang J, Mouritz AP, Wang CH (2013). "Healing of carbon fibre–epoxy composite T-joints using mendable polymer fibre stitching".Composites Part B: Engineering.45:1499–507.doi:10.1016/j positesb.2012.08.022.
  76. ^Cullinan JF, Wisnom M, Bond I (2015).A Novel Method for the Manipulation of Damage and In-Situ Repair of Composite T-Joints.56th AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference. Reston, Virginia: American Institute of Aeronautics and Astronautics. p. 1577.
  77. ^Minakuchi S, Sun D, Takeda N (2014)."Hierarchical system for autonomous sensing-healing of delamination in large-scale composite structures".Smart Materials and Structures.23(11): 115014.Bibcode:2014SMaS...23k5014M.doi:10.1088/0964-1726/23/11/115014.S2CID136572563.
  78. ^Kessler MR, White SR (2001)."Self-activated healing of delamination damage in woven composites"(PDF).Composites Part A: Applied Science and Manufacturing.32(5):683–99.doi:10.1016/s1359-835x(00)00149-4.hdl:2142/112657.
  79. ^abKessler MR, Sottos NR, White SR (2003). "Self-healing structural composite materials".Composites Part A: Applied Science and Manufacturing.34(8):743–53.doi:10.1016/S1359-835X(03)00138-6.
  80. ^Patel AJ, Sottos NR, Wetzel ED, White SR (2010). "Autonomic healing of low-velocity impact damage in fibre-reinforced composites".Composites Part A: Applied Science and Manufacturing.41(3):360–68.doi:10.1016/j positesa.2009.11.002.
  81. ^Norris CJ, White JA, McCombe G, Chatterjee P, Bond IP, Trask RS (2012). "Autonomous stimulus triggered self-healing in smart structural composites".Smart Materials and Structures.21(9): 094027.Bibcode:2012SMaS...21i4027N.doi:10.1088/0964-1726/21/9/094027.S2CID137489472.
  82. ^Bleay SM, Loader CB, Hawyes VJ, Humberstone L, Curtis PT (2001). "A smart repair system for polymer matrix composites".Composites Part A: Applied Science and Manufacturing.32(12):1767–76.doi:10.1016/s1359-835x(01)00020-3.
  83. ^Trask RS, Bond IP (2006). "Biomimetic self-healing of advanced composite structures using hollow glass fibres".Smart Materials and Structures.15(3):704–10.Bibcode:2006SMaS...15..704T.doi:10.1088/0964-1726/15/3/005.S2CID15100402.
  84. ^Trask RS, Bond IP (June 2010)."Bioinspired engineering study of Plantae vascules for self-healing composite structures".Journal of the Royal Society, Interface.7(47):921–31.doi:10.1098/rsif.2009.0420.PMC2871803.PMID19955122.
  85. ^Esser-Kahn AP, Thakre PR, Dong H, Patrick JF, Vlasko-Vlasov VK, Sottos NR, et al. (August 2011). "Three-dimensional microvascular fiber-reinforced composites".Advanced Materials.23(32):3654–58.Bibcode:2011AdM....23.3654E.doi:10.1002/adma.201100933.PMID21766345.S2CID46096597.
  86. ^Huang CY, Trask RS, Bond IP (August 2010)."Characterization and analysis of carbon fibre-reinforced polymer composite laminates with embedded circular vasculature".Journal of the Royal Society, Interface.7(49):1229–41.doi:10.1098/rsif.2009.0534.PMC2894872.PMID20150337.
  87. ^Aïssa B, Therriault D, Haddad E, Jamroz W (2011)."Self-Healing Materials Systems: Overview of Major Approaches and Recent Developed Technologies".Advances in Materials Science and Engineering.2012:1–17.doi:10.1155/2012/854203.
  88. ^abChen Y, Guan Z (September 2014). "Multivalent hydrogen bonding block copolymers self-assemble into strong and tough self-healing materials".Chemical Communications.50(74):10868–70.doi:10.1039/C4CC03168G.PMID25090104.
  89. ^Binder WH (2013). "Self-Healing Ionomers".Self-healing polymers: from principles to applications(1 ed.). Weinheim: Wiley-VCH Verlag GmbH. pp.315–34.doi:10.1002/9783527670185.ch13.ISBN978-3-527-33439-1.
  90. ^Varley RJ, Zwaag SV (2008). "Development of a quasi-static test method to investigate the origin of self-healing in ionomers under ballistic conditions".Polymer Testing.27:11–19.doi:10.1016/j.polymertesting.2007.07.013.hdl:10536/DRO/DU:30095736.
  91. ^Liua YL, Chuoa TW (2013). "Self-healing polymers based on thermally reversible Diels–Alder chemistry".Polymer Chemistry.4(7):2194–05.doi:10.1039/C2PY20957H.
  92. ^Jin H, Miller GM, Pety SJ, Griffin AS, Stradley DS, Roach D, Sottos NR, White SR (2013). "Fracture behavior of a self-healing, toughened epoxy adhesive".Int. J. Adhes. Adhes.44:157–65.doi:10.1016/j.ijadhadh.2013.02.015.
  93. ^Blaiszik BJ, Kramer SL, Grady ME, McIlroy DA, Moore JS, Sottos NR, White SR (January 2012). "Autonomic restoration of electrical conductivity".Advanced Materials.24(3):398–401.Bibcode:2012AdM....24..398B.doi:10.1002/adma.201102888.PMID22183927.S2CID2225085.
  94. ^Kang S, Jones AR, Moore JS, White SR, Sottos NR (2014). "Microencapsulated carbon black suspensions for restoration of electrical conductivity".Adv. Funct. Mater.24(20):2947–56.doi:10.1002/adfm.201303427.S2CID18494560.
  95. ^Markvicka EJ, Bartlett MD, Huang X, Majidi C (July 2018). "An autonomously electrically self-healing liquid metal-elastomer composite for robust soft-matter robotics and electronics".Nature Materials.17(7):618–24.Bibcode:2018NatMa..17..618M.doi:10.1038/s41563-018-0084-7.PMID29784995.S2CID29160161.
  96. ^Huang M, Yang J (2011). "Facile microencapsulation of HDI for self-healing anticorrosion coatings".Journal of Materials Chemistry.21(30):11123–30.doi:10.1039/C1JM10794A.
  97. ^Yang J, Keller MW, Moore JF, White SR, Sottos NR (2008). "Microencapsulation of Isocyanates for Self-Healing Polymers".Macromolecules.41(24):9650–55.Bibcode:2008MaMol..41.9650Y.doi:10.1021/ma801718v.
  98. ^Meng LM, Yuan YC, Rong MZ, Zhang MQ (2010). "A dual mechanism single-component self-healing strategy for polymers".Journal of Materials Chemistry.20(29):5969–6196.doi:10.1039/C0JM00268B.
  99. ^Jin HH, Mangun CL, Stradley DS, Moore JS, Sottos NR, White SR (2012). "Self-healing thermoset using encapsulated epoxy-amine healing chemistry".Polymer.53(2):581–87.doi:10.1016/j.polymer.2011.12.005.
  100. ^Suryanarayana C, Rao KC, Kumar (2008). "Preparation and characterization of microcapsules containing linseed oil and its use in self-healing coatings".Progress in Organic Coatings.63:72–78.doi:10.1016/j.porgcoat.2008.04.008.
  101. ^Jadhav RS, Hundiwale DG, Mahulikar PP (2011). "Synthesis and Characterization of Phenol–Formaldehyde Microcapsules Containing Linseed Oil and Its Use in Epoxy for Self-Healing and Anticorrosive Coating".Journal of Applied Polymer Science.119(5):2911–16.doi:10.1002/app.33010.
  102. ^Samadzadeha M, Bouraa SH, Peikaria M, Ashrafib A, Kasirihac M (2011). "Tung oil: An autonomous repairing agent for self-healing epoxy coatings".Progress in Organic Coatings.70(4):383–87.doi:10.1016/j.porgcoat.2010.08.017.
  103. ^glass-mediated self-healing ability in high emissivity coatingsCorrosion Science, 2019, 146, pp.233-246.
  104. ^Wang, Lu; Wang, Weiyan; Fu, Qiangang (2020)."The improvement of the self-healing ability of MoSi2 coatings at 900–1200 °C by introducing SiB6".Journal of the European Ceramic Society.40(8):2896–2906.doi:10.1016/j.jeurceramsoc.2020.01.048.
  105. ^abDe Rooij M, Van Tittelboom K, De Belie N, Schlangen E, eds. (2011).Self-Healing Phenomena in Cement-Based Materials.RILEM State-of-the-Art Reports. Vol. 11. Springer Netherlands.doi:10.1007/978-94-007-6624-2.ISBN978-94-007-6624-2.
  106. ^Edvardsen C (1999). "Water permeability and autogenous healing of cracks in concrete".ACI Materials Journal.96(4):448–54.doi:10.14359/645.
  107. ^Snoeck, Didier; Van Tittelboom, Kim; Steuperaert, Stijn; Dubruel, Peter; De Belie, Nele (2012-03-15)."Self-healing cementitious materials by the combination of microfibres and superabsorbent polymers".Journal of Intelligent Material Systems and Structures.25:13–24.doi:10.1177/1045389X12438623.hdl:1854/LU-6869809.S2CID92983639.
  108. ^Snoeck, Didier (2018-11-15)."Superabsorbent polymers to seal and heal cracks in cementitious materials".RILEM Technical Letters.3:32–38.doi:10.21809/rilemtechlett.2018.64.hdl:1854/LU-8664851.
  109. ^Snoeck, Didier; Pel, Leo; De Belie, Nele (2020-01-20)."Autogenous Healing in Cementitious Materials with Superabsorbent Polymers Quantified by Means of NMR".Scientific Reports.10(1): 642.Bibcode:2020NatSR..10..642S.doi:10.1038/s41598-020-57555-0.PMC6971030.PMID31959802.
  110. ^Mostavi E, Asadi S, Hassan M, Alansari M (December 2015)."Evaluation of Self-Healing Mechanisms in Concrete with Double-Walled Sodium Silicate Microcapsules"(PDF).Journal of Materials in Civil Engineering.27(12): 04015035.doi:10.1061/(ASCE)MT.1943-5533.0001314.
  111. ^Ehrlich NL (1996). "How microbes influence mineral growth and dissolution".Chemical Geology.1–4(132):5–9.Bibcode:1996ChGeo.132....5E.doi:10.1016/S0009-2541(96)00035-6.
  112. ^Jonkers HM, Schlangen E (2007). AJM Schmetz, van der Zwaag (eds.). "Crack repair by concrete immobilized bacteria".Proceedings of the First International Conference on Self Healing Materials.Springer:1–7.ISBN9781402062490.
  113. ^Jonkers H (2007). "Self healing concrete: a biological approach". In van der Zwaag S (ed.).Self Healing Materials: An alternative approach to 20 centuries of materials science.Dordrecht: Springer. pp.195–204.
  114. ^Jonkers HM, Thijssen A, Muyzer G, Copuroglu O, Schlangen E (2010). "Application of bacteria as self-healing agent for the development of sustainable concrete".Ecological Engineering.36(2):230–35.Bibcode:2010EcEng..36..230J.doi:10.1016/j.ecoleng.2008.12.036.
  115. ^Jonkers H (2011)."Bacteria-based self-healing concrete"(PDF).HERON.56(1/2).
  116. ^Van Tittelboom K, De Belie N, Van Loo D, Jacobs P (2011). "Self-healing efficiency of cementitious materials containing tubular capsules filled with healing agent".Cement and Concrete Composites.33(4):497–505.doi:10.1016/j.cemconcomp.2011.01.004.
  117. ^Wang J, Van Tittelboom K, De Belie N, Verstraete W (2012). "Use of silica gel or polyurethane immobilized bacteria for self-healing concrete".Construction and Building Materials.26(1):532–40.doi:10.1016/j.conbuildmat.2011.06.054.
  118. ^Ono M, Nakao W, Takahashi K, Nakatani M, Ando K (2007). "A new methodology to guarantee the structural integrity of Al2O3/SiC composite using crack healing and a proof test".Fatigue & Fracture of Engineering Materials & Structures.30(7):599–607.doi:10.1111/j.1460-2695.2007.01132.x.
  119. ^Yang HJ, Pei YT, Rao JC, De Hosson JT (2012). "Self-healing performance of Ti2AlC ceramic ".Journal of Materials Chemistry.22(17):8304–13.doi:10.1039/C2JM16123K.
  120. ^Song GM, Pei YT, Sloof WG, Li SB, De Hosson JT, Van der Zwaag S (January 2008). "Oxidation-induced crack healing in Ti3AlC2ceramics ".Scripta Materialia.58(1):13–16.doi:10.1016/j.scriptamat.2007.09.006.
  121. ^Li S, Song G, Kwakernaak K, van der Zwaag S, Sloof WG (2012). "Multiple crack healing of a Ti2AlC ceramic ".Journal of the European Ceramic Society.32(8):1813–20.doi:10.1016/j.jeurceramsoc.2012.01.017.
  122. ^Farle AS, Kwakernaak C, van der Zwaag S, Sloof WG (2015). "A conceptual study into the potential of Mn+1AXn-phase ceramics for self-healing of crack damage".Journal of the European Ceramic Society.35:37–45.doi:10.1016/j.jeurceramsoc.2014.08.046.
  123. ^Nakao W, Takahashi K, Ando K (2009-01-20).Self-Healing materials, Design, strategies and applications.Wiley-VCH Verkag GmbH & Co KGaA. p. 188.ISBN978-3-527-31829-2.
  124. ^Nakao W, Abe S (2012). "Enhancement of the self-healing ability in oxidation induced self-healing ceramic by modifying the healing agent".Smart Materials and Structures.21(2): 025002.Bibcode:2012SMaS...21b5002N.doi:10.1088/0964-1726/21/2/025002.S2CID137243253.
  125. ^Nakao W, Takahashi K, Ando K (2007). "Threshold stress during crack healing treatment of structural ceramics having crack healing ability".Materials Letters.61(13):2711–13.Bibcode:2007MatL...61.2711N.doi:10.1016/j.matlet.2006.04.122.
  126. ^Ando K, Kim BS, Chu MC, Saito S, Takahashi K (2004). "Crack-healing and Mechanical Behaviour of Al2O3/Sic composites at elevated temperature".Fatigue & Fracture of Engineering Materials & Structures.27(7):533–41.doi:10.1111/j.1460-2695.2004.00785.x.
  127. ^Lumley RN, Morton AJ, Polmear IJ (2002). "Enhanced creep performance in an Al-Cu-Mg-Ag alloy through underageing".Acta Materialia.50(14):3597–3608.Bibcode:2002AcMat..50.3597L.doi:10.1016/S1359-6454(02)00164-7.
  128. ^Laha K, Kyono J, Kishimoto S, Shinya N (2005). "Beneficial effect of B segregation on creep cavitation in a type 347 austenitic stainless steel".Scripta Materialia.52(7):675–78.doi:10.1016/j.scriptamat.2004.11.016.
  129. ^Laha K, Kyono J, Shinya N (2007). "An advanced creep cavitation resistance Cu-containing 18Cr-12Ni-Nb austenitic stainless steel".Scripta Materialia.56(10):915–18.doi:10.1016/j.scriptamat.2006.12.030.
  130. ^He SM, Van Dijk NH, Schut H, Peekstok ER, van der Zwaag S (2010)."Thermally activated precipitation at deformation-induced defects in Fe-Cu and Fe-Cu-B-N alloys studied by positron annihilation spectroscopy".Physical Review.B 81(9): 094103.Bibcode:2010PhRvB..81i4103H.doi:10.1103/PhysRevB.81.094103.
  131. ^He SM, Van Dijk NH, Paladugu M, Schut H, Kohlbrecher J, Tichelaar FD, Van der Zwaag S (2010)."In situ determination of aging precipitation in deformed Fe-Cu and Fe-Cu-B-N alloys by time-resolved small-angle neutron scattering".Physical Review.B 82(17): 174111.Bibcode:2010PhRvB..82q4111H.doi:10.1103/PhysRevB.82.174111.
  132. ^Zhang S, Kohlbrecher J, Tichelaar FD, Langelaan G, Brück E, Van Der Zwaag S, Van Dijk NH (2013)."Defect-induced Au precipitation in Fe–Au and Fe–Au–B–N alloys studied by in situ small-angle neutron scattering".Acta Materialia.61(18):7009–19.Bibcode:2013AcMat..61.7009Z.doi:10.1016/j.actamat.2013.08.015.
  133. ^Zhang S, Kwakernaak C, Sloof W, Brück E, van der Zwaag S, van Dijk N (2015). "Self Healing of Creep Damage by Gold Precipitation in Iron Alloys".Advanced Engineering Materials.17(5):598–603.doi:10.1002/adem.201400511.S2CID137674278.
  134. ^Barr, Christopher M.; Duong, Ta; Bufford, Daniel C.; Milne, Zachary; Molkeri, Abhilash; Heckman, Nathan M.; Adams, David P.; Srivastava, Ankit; Hattar, Khalid; Demkowicz, Michael J.; Boyce, Brad L. (2023-07-19)."Autonomous healing of fatigue cracks via cold welding".Nature.620(7974):552–556.Bibcode:2023Natur.620..552B.doi:10.1038/s41586-023-06223-0.ISSN1476-4687.PMID37468631.S2CID259995049.
  135. ^"Stunning discovery: Metals can heal themselves".Retrieved2023-07-25.
  136. ^Xu, G. Q.; Demkowicz, M. J. (2013-10-02)."Healing of Nanocracks by Disclinations".Physical Review Letters.111(14): 145501.Bibcode:2013PhRvL.111n5501X.doi:10.1103/PhysRevLett.111.145501.hdl:1721.1/84982.PMID24138252.S2CID2019945.
  137. ^Taylor, Danielle Lynne; in het Panhuis, Marc (November 2016)."Self-Healing Hydrogels".Advanced Materials.28(41):9060–9093.Bibcode:2016AdM....28.9060T.doi:10.1002/adma.201601613.PMID27488822.S2CID29306791.
  138. ^Bertsch, Pascal; Diba, Mani; Mooney, David J.; Leeuwenburgh, Sander C. G. (25 January 2023)."Self-Healing Injectable Hydrogels for Tissue Regeneration".Chemical Reviews.123(2):834–873.doi:10.1021/acs.chemrev.2c00179.hdl:2066/291335.PMC9881015.PMID35930422.
  139. ^Embaye NB, Ramini SK, Kuzyk MG (August 2008). "Mechanisms of reversible photodegradation in disperse orange 11 dye doped in PMMA polymer".The Journal of Chemical Physics.129(5): 054504.arXiv:0808.3346.Bibcode:2008JChPh.129e4504E.doi:10.1063/1.2963502.PMID18698911.S2CID16251414.
  140. ^Ramini SK, Dawson N, Kuzyk MG (2011-10-01). "Testing the diffusion hypothesis as a mechanism of self-healing in Disperse Orange 11 doped in poly(methyl methacrylate)".JOSA B.28(10):2408–12.arXiv:1106.2732.Bibcode:2011JOSAB..28.2408R.doi:10.1364/JOSAB.28.002408.ISSN1520-8540.S2CID118576642.
  141. ^Ramini SK, Kuzyk MG (August 2012). "A self healing model based on polymer-mediated chromophore correlations".The Journal of Chemical Physics.137(5): 054705.arXiv:1205.0481.Bibcode:2012JChPh.137e4705R.doi:10.1063/1.4739295.PMID22894369.S2CID5512565.
  142. ^abDemmenie, Menno (19 January 2022)."Scratch-Healing Behavior of Ice by Local Sublimation and Condensation".Journal of Physical Chemistry C.126(4):2179–2183.doi:10.1021/acs.jpcc.1c09590.PMC8819648.PMID35145575.
  143. ^Kingery, W. D. "Regelation, surface diffusion, and ice sintering." Journal of Applied Physics 31.5 (1960): 833-838.
  144. ^Yang Z, Wei Z, Le-ping L, Hong-mei W, Wu-jun L (2011)."The self-healing composite anticorrosion coating".Physics Procedia.18:216–21.Bibcode:2011PhPro..18..216Y.doi:10.1016/j.phpro.2011.06.084.ISSN1875-3892.
  145. ^Zhu M, Rong MZ, Zhang MQ (2014). "Self-healing polymeric materials towards non-structural recovery of functional properties".Polymer International.63(10):741–49.doi:10.1002/pi.4723.
  146. ^Pacheco J, Šavija B, Schlangen E, Polder RB (2014). "Assessment of cracks in reinforced concrete by means of electrical resistance and image analysis".Construction and Building Materials.65:417–26.doi:10.1016/j.conbuildmat.2014.05.001.
  147. ^Mauldin TC, Kessler MR (2010)."Self-healing polymers and composites".International Materials Reviews.55(6):317–46.Bibcode:2010IMRv...55..317M.doi:10.1179/095066010X12646898728408.
  148. ^"Self-healing elastomer enters industrial production".arkema.Retrieved2015-12-13.
  149. ^Bourzac K (December 12, 2008)."First Self-Healing Coatings".technologyreview.Retrieved18 November2016.
  150. ^Rincon P (30 October 2010)."Time to heal: The materials that repair themselves".BBC.Retrieved19 May2013.
edit
Retrieved from "https://en.wikipedia.org/w/index.php?title=Self-healing_material&oldid=1259458289"