Wikipedia

Tappet

Atappetorvalve lifteris avalve traincomponent which converts rotational motion into linear motion in activating a valve. It is most commonly found ininternal combustion engines,where it converts the rotational motion of the camshaft into linear motion of intake and exhaust valves, either directly or indirectly.

Roller tappet (shown in red) in an internal combustion engine

An earlier use of the term was for part of the valve gear inbeam enginesbeginning in 1715. The term is also used for components inpneumatic cylindersandweaving loom.

History

edit
Beam enginewith tappet block on the vertical plug rod. The tappet block acts on the curved horn beneath it

The first recorded use of the term tappet is as part of thevalve gearin the 1715Newcomen engine,an early form of steam engine. Early versions of the Newcomen engines from 1712 had manually operated valves, but by 1715 this repetitive task had been automated through the use of tappets. The beam of the engine had a vertical 'plug rod' hung from it, alongside the cylinder. Adjustable blocks or 'tappets' were attached to this rod and as the beam moved up and down, the tappets pressed against long levers or 'horns' attached to the engine's valves, working the cycle of steam and injection water valves to operate the engine.[1]

This operation by tappets on a plug rod continued into the early twentieth century with theCornish engine.[2]

From the 19th century onwards, most steam engines usedslide valvesorpiston valves,which do not require the use of tappets.

In anoverhead valveengine the tappets (on right) are sandwiched betweenpushrodsand thecamshaft

In aninternal combustion engine,a tappet (also called a 'valve lifter' or 'cam follower')[3][4][5]is the component which converts the rotation of the camshaft into vertical motion to open and close an intake or exhaustvalve.

The principal types of tappets used in automotive engines are solid, hydraulic, and roller.[6][7]

To reduce wear from the rotating camshaft, tappets are usually circular and allowed, or even encouraged, to rotate in place. This minimizes wear caused by the camshaft contacting the same point on the base of the tappet each valve cycle, which can result in grooving. However, in some relatively small engines with many cylinders (such as theDaimler '250' V8 engine), the tappets were small and non-rotating.[citation needed]

The base of most plain tappets is given a slightconvexprofile to soften contact of the leading edge of the camshaft lobe.

Alternatives

edit

An alternative to the tappet is the “finger follower”, which is a pivoting beam that is used to convert the camshaft rotation into opening and closing of a valve. Finger followers are used in some high-performancedual overhead camshaft(DOHC) engines, most commonly in motorcycles and sports cars.[8]

Adjusting valve clearance

edit

On most overhead valve (OHV) engines, proper clearance between the camshaft and tappet is achieved by turning a set screw in the end of the rocker arm that contacts the end of the pushrod until a desired gap is achieved using afeeler gauge.Too large a gap results in wear from misaligned parts and compromised engine performance, and too small can lead to bent pushrods or burnt valves.

A locknut secures the set screw-in place. Loose set screws can cause catastrophic engine failure, which has led to fatal aircraft crashes.[9]

On some OHV engines in the 1960s, such as theFord Taunus V4 engineandOpel CIH engine,the tappet adjustment was done by setting the height of the rocker pivot point (rather than the typical method of a rocker-end adjustment screw). On the 1965-1970 versions of the Opel CIH engine with solid tappets, the tappet adjustment was conducted with the engine running.[10]

Hydraulic tappets

edit
Hydraulic tappets (along with rockers, valves and cylinder head) for a 1980-1985Ford CVH engine

Ahydraulic tappet,also known as a "hydraulic valve lifter" and "hydraulic lash adjuster", contains a small hydraulic piston that becomes filled with pressurised engine oil.[4][11]The piston acts as a hydraulic spring that automatically adjusts the tappet clearance according to the oil pressure. Although the movements of the piston are small and infrequent, they are sufficient to make the valve actuation self-adjusting so that there is no need to manually adjust the clearance of the tappets.

Hydraulic tappets depend on a supply of clean oil at the appropriate pressure. When starting a cold engine, with low oil pressure, hydraulic tappets are often noisy for a few seconds, until they position themselves correctly.

Roller tappets

edit

Early automotive engines[when?]used a roller at the contact point with the camshaft,[12]: 44 however as engine speeds increased, 'flat tappets' with plain ends became far more common than tappets with rollers. However in recent times, roller tappets and rocker arms with roller tappet ends have made a resurgence due to the lower friction providing greater efficiency and reducing drag.[7]

Valvetrain layouts

edit
Diagram of a sidevalve engine

In asidevalve engine— a common design for car engines until the 1950s— the valves are mounted at the sides of the cylinder and face upwards. This means that the camshaft could be placed directly beneath the valves, without the need for a rocker. With lower cylinder blocks, the tappets could drive the valves directly without needing even a push rod.[4][13]Sidevalve engines also required regular adjustment of the tappet clearance, and in this case it was the tappets themselves that were adjusted directly. Small access plates were provided on the sides of the cylinder block, giving access to the gap between the valves and tappets. Some tappets had a threaded adjuster, but simpler engines could be adjusted by grinding down the ends of the valve stem directly. As the tappet adjustment always consisted of expanding the clearance (re-grinding valves into their valve seats during de-coking makes them sit lower, thus reducing the tappet clearance), adjustment by shortening the valve stems was a viable method. Eventually the valves would be replaced entirely, a relatively common operation for engines of this era.

In apushrod engine(OHV), the tappets are located down in theengine blockand operate long, thinpushrodswhich transfer the motion (via the rocker arms) to the valves located at the top of the engine.[14]

In asingle overhead camshaft(SOHC) engine, the tappets are integrated into the design of the rocker arms as one piece, since the camshaft interacts with the rocker arm directly. Mass-production of SOHC engines for passenger cars became more common in the 1970s, in the form ofcrossflow cylinder headswithoverhead rockerslocated directly above a single overhead camshaft, as a more efficient design which could be cost-effectively manufactured. The 1970-2001Ford Pinto enginewas one of the first mass-production engines to use an SOHC design with a toothed cambelt.[15]In this configuration, the rockers combine the function of sliding tappet, rocker and adjustment device. Adjustment of the valve clearance was usually by a threaded stud at the valve end of the rocker. The linear sliding tappet side often had a high rate of wear and demanded careful lubrication with oil containing zinc additives. A relatively uncommon design of an SOHC camshaft with four valves per cylinder was first used in the 1973-1980Triumph Dolomite Sprintinline-four engine, which used a camshaft with 8 lobes that actuated the 16 valves via a clever arrangement of rocker arms.[16][17]

DOHCengine with a bucket tappet

Double overhead camshaft(DOHC) engines were first developed as high performance aircraft and racing engines, with the camshafts mounted directly over the valves and driving them through a simple 'bucket tappet'. Most engines used a crossflow cylinder head with the valves in two rows in line with their corresponding camshaft. The tappet clearance adjustment is typically set using a smallshim,located either above or below the tappet. Shims were made in a range of standard thicknesses and a mechanic would swap them to change the tappet gap. In early DOHC engines, the engine would first be assembled with a default shim of known thickness, then the gap measured. This measurement would be used to calculate the thickness of shim that would result in the desired gap. After installation of the new shim, the gaps would then be measured again to verify that the clearance was correct. As the camshaft had to be removed to change the shims, this was a very time consuming operation (especially since the position of the camshaft could vary slightly each time it was re-installed). Later engines used an improved design where the shims were located above the tappets, which allowed each shim to be changed without removing either the tappet or camshaft. A drawback of this design is that the rubbing surface of the tappet becomes the surface of the shim, which is a difficult problem of mass-production metallurgy. The first mass production engine to use this system was the 1966-2000Fiat Twin Cam engine,followed by engines from Volvo and the water-cooled Volkswagens.[18]

Other uses

edit
Valve chest, arc valve and tappet of a pneumatic rock drill

The term 'tappet' is also used, obscurely, as a component of valve systems for other machinery, particularly as part of abash valveinpneumatic cylinders.Where a reciprocating action is produced, such as for a pneumatic drill orjackhammer,the valve may be actuated byinertiaor by the movement of the working piston. As the piston hammers back and forth, it impacts a small tappet, which in turn moves the air valve and so reverses the flow of air to the piston.[19]

In weaving looms, a tappet is a mechanism which helps form the shed or opening in the warp threads (long direction) of the material through which the weft threads (side to side or short direction) are passed. The tappets form the basic patterns in the material such as plain weave, twill, denim, or satin weaves. Harris tweed is still woven on looms in which tappets are still used.[citation needed]

See also

edit

References

edit
  1. ^The Newcomen Memorial Engine.Dartmouth, England:Newcomen Society.
  2. ^Woodall, Frank D. (1975).Steam Engines and Waterwheels.Moorland. pp. 31–34.ISBN0903485354.
  3. ^Setright & Anatomy of the Motor Car,p. 33
  4. ^abcHillier, V.A.W. (1981).Fundamentals of Motor Vehicle Technology(4th ed.). Stanley Thornes. p. 44.ISBN0-09-143161-1.
  5. ^"Valve system operation"(PDF).thecarguys.net.Retrieved11 February2020.
  6. ^"Hydraulic vs. Solid Lifters".summitracing.Retrieved29 September2024.
  7. ^ab"What is the difference between a flat tappet and a roller camshaft?".summitracing.Retrieved29 September2024.
  8. ^"About Those Finger Followers On Sportbike Engines".cycleworld.Retrieved11 February2020.
  9. ^Alexander, Robert Charles (1999).The Inventor of Stereo: The Life and Works of Alan Dower Blumlein.Focal Press.ISBN0-240-51628-1.
  10. ^"Tuning the 1.9 Litre Opel (Part I)"(PDF).opelclub.Retrieved21 February2020.
  11. ^Setright & Anatomy of the Motor Car,p. 33
  12. ^Hillier, Victor Albert Walter (1991).Fundamentals of Motor Vehicle Technology.Nelson Thornes.ISBN978-0-7487-0531-3.Retrieved11 February2020.
  13. ^Setright & Anatomy of the Motor Car,p. 34
  14. ^Setright, L. J. K.(1976). "Valve gear". In Ian Ward (ed.).Anatomy of the Motor Car.Orbis. pp. 29–36.ISBN0-85613-230-6.
  15. ^"Ford SOHC (Pinto) Tuning Guide".burtonpower.Retrieved20 March2020.
  16. ^"Dolomite History".triumphclub.co.nz.Retrieved20 March2020.
  17. ^"Triumph Dolomite Sprint".classiccars4sale.net.Retrieved20 March2020.
  18. ^Setright & Anatomy of the Motor Car,p. 34
  19. ^Kennedy, Rankin.The Book of Modern Engines and Power Generators.Vol. VI (1912 ed.). London: Caxton. p. 162-166.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Tappet&oldid=1260025618"