Dehumidifier

Adehumidifieris anair conditioningdevice which reduces and maintains the level ofhumidityin the air.^[1]This is done usually for health orthermal comfortreasons, or to eliminate mustyodorand to prevent the growth ofmildewby extracting water from the air. It can be used for household, commercial, or industrial applications. Large dehumidifiers are used in commercial buildings such as indoorice rinks^[2]andswimming pools,as well as manufacturing plants or storage warehouses. Typical air conditioning systems combine dehumidification with cooling, by operating cooling coils below the dewpoint and draining away the water that condenses.

Dehumidifiers extract water from air that passes through the unit. There are two common types of dehumidifiers: condensate dehumidifiers and desiccant dehumidifiers, and there are also other emerging designs.

Condensate dehumidifiers use arefrigeration cycleto collect water known ascondensate,which is normally considered to begreywaterbut may at times be reused for industrial purposes. Some manufacturers offerreverse osmosisfilters to turn the condensate into potable water.

Desiccantdehumidifiers (known also as absorption dehumidifiers) bond moisture with hydrophilic materials such assilica gel.Cheap domestic units contain single-use hydrophilic substance cartridges, gel, or powder. Larger commercial units regenerate the sorbent by using hot air to remove moisture and expel humid air outside the room.

An emerging class of membrane dehumidifiers, such as the ionic membrane dehumidifier, dispose of water as a vapor rather than liquid. These newer technologies may aim to address smaller system sizes or reach superior performance.

Theenergy efficiencyof dehumidifiers can vary widely.

History[edit]

The first dehumidifier was created by American inventorWillis Carrierin 1902 to dehumidify aBrooklynprinting plant.^[3]Carrier cited the discovery as later motivating further discoveries in air conditioning.^[1]These “active” dehumidifiers condensed water from air. However, “passive” humidity control, such as increased natural ventilation, has been used since ancient times.^[4]

Types[edit]

Thermal condensation dehumidification[edit]

These methods rely on drawing air across a cold surface. Since thesaturation vapor pressureof water decreases with decreasing temperature, the water in the aircondenseson the surface, separating the water from the air.

Refrigeration (electric)[edit]

Electric refrigeration dehumidifiers are the most common type of dehumidifiers. They work by drawing moist air over arefrigeratedevaporator with a fan. There are 3 main types of evaporators. They are coiled tube, fin and tube, andmicrochanneltechnology.

The coldevaporator coilof the refrigeration device condenses the water, which is removed, and then the air is reheated by thecondenser coil.The now dehumidified, re-warmed air is released into the room. This process works most effectively at higher ambient temperatures with a highdew pointtemperature. In cold climates, the process is less effective. Highest efficiency is reached above 20 °C (68 °F) and 45% relative humidity. Thisrelative humidityvalue is higher if the temperature of the air is lower.^[5]

This type of dehumidifier differs from a standard air conditioner in that both the evaporator and the condenser are placed in the same air path. A standard air conditioner transfers heat energy out of the room because its condenser coil releases heat outside. However, since all components of the dehumidifier are in thesameroom, no heat energy is removed. Instead, the electricpowerconsumed by the dehumidifier remains in the room as heat, so the room is actuallyheated,just as by anelectric heaterthat draws the same amount of power.

In addition, if water is condensed in the room, the amount of heat previously needed to evaporate that water also is re-released in the room (thelatent heat of vaporization). The dehumidification process is the inverse of adding water to the room with anevaporative cooler,and instead releases heat. Therefore, an in-room dehumidifier will always warm the room and reduce the relative humidity indirectly, as well as reducing the humidity more directly, by condensing and removing water.

Diagram showing airflow through a heat-recovering dehumidifier

Warm, moist air is drawn into the unit at A in the diagram above. This air passes into a crossflow plate heat exchanger (B) where a substantial proportion of the sensible heat is transferred to a cool supply air stream. This process brings the extracted air close to saturation. The air then passes to the plenum chamber of the extract fan (C) where a portion of it may be rejected to outside. The amount that is rejected can be varied and is determined either by legislation on fresh air requirements, or by the requirement to maintain a fresh, odour free environment. The balance of the air then passes into the evaporator coil of theheat pumpwhere it is cooled and the moisture is condensed. This process yields substantial amounts of latent energy to the refrigeration circuit. Fresh air is then introduced to replace the amount that was extracted and the mix is discharged by the supply fan (G) to the crossflow plate exchanger (B) where it is heated by the extract air from the pool. This pre-warmed air then passes through the heat pump condenser (F) where it is heated by the latent energy removed during the condensation process as well as the energy input to the compressor. The warm dry air is then discharged to the room.^{[citation needed]}

Conventional air conditioners[edit]

A conventionalair conditioneris very similar to an electric dehumidifier and inherently acts as a dehumidifier when chilling the air. In an air conditioner, however, the air passes over the cold evaporator coils and then directly into the room. It is not re-heated by passing over the condenser, as in a refrigeration dehumidifier. Instead, the refrigerant is pumped by the compressor to a condenser which is located outside the room to be conditioned, and the heat is then released to the outside air. Conventional air conditioners use additional energy exhausting air outside, and new air can have more moisture than the room needs, such as a pool room that already holds a high amount of moisture in the air.^{[citation needed]}

The water that condenses on the evaporator in an air conditioner is usually routed to remove extracted water from the conditioned space. Newer high-efficiency window units use the condensed water to help cool thecondenser coilby evaporating the water into the outdoor air, while older units simply allowed the water to drip outside.

Spray dehumidifiers[edit]

When water is chilled below the atmosphericdew point,atmospheric water will condense onto it faster than water evaporates from it. Spray dehumidifiers mix sprays ofchilled waterand air to capture atmospheric moisture. They also capture pollutants and contaminants like pollen, for which purpose they are sometimes called "air washers".

Makeshift dehumidifiers[edit]

Because window air conditioner units have condensers and expansion units, some of them can be used as makeshift dehumidifiers by sending their heat exhaust back into the same room as the cooled air, instead of the outside environment. If the condensate from the cooling coils is drained away from the room as it drips off the cooling coils, the result will be room air that is drier but slightly warmer.

However, many window air conditioners are designed to dispose of condensate water by re-evaporating it into the exhaust air stream, which cancels out the air humidity decrease caused by the condensation of moisture on the cooling coils. To be effective as a dehumidifier, an air conditioner must be designed or modified so that most or all of the water that condenses is drained away in liquid form, rather than re-evaporated. Even if condensate is drained, a modified air conditioner is still less efficient than a single-purpose appliance with a design optimized for dehumidification. Dehumidifiers are designed to pass air directly over the cooling coils and then the heating coils in a single efficient pass through the device.

In addition, most air conditioners are controlled by athermostatwhich senses temperature, rather than ahumidistatthat senses humidity and is typically used to control a dehumidifier. A thermostat is not designed for the control of humidity, and controls it poorly if at all.

Ice buildup[edit]

Under certain conditions of temperature and humidity,icecan form on a refrigeration dehumidifier'sevaporator coils.The ice buildup can impede airflow and eventually form a solid block encasing the coils.^[6]This buildup prevents the dehumidifier from operating effectively, and can cause water damage if condensed water drips off the accumulated ice and not into the collection tray. In extreme cases, the ice can deform or distort mechanical elements, causing permanent damage.

Better-quality dehumidifiers may have a frost or ice sensor. These will turn off the machine and allow the ice-covered coils to warm and defrost. Once defrosted, the machine usually will automatically restart. Most ice sensors are simplethermal switchesand do not directly sense the presence or absence of ice buildup. An alternative design senses the impeded airflow and shuts off the cooling coils in a similar manner.

Certain malfunctions of dehumidifiers, such as partial loss of refrigerant, can cause repeated icing of the coils. This condition requires repair or replacement of the equipment.

Thermoelectric dehumidifiers[edit]

Thermoelectric dehumidifiers use aPeltier heat pumpto cool a surface and condense water vapor from the air. The design is simpler and has the benefit of being quieter compared to a dehumidifier with a mechanical compressor. However, because of itsrelatively poor Coefficient of Performance,this design is mainly used for small dehumidifiers. Ice buildup may be a problem, similar to problems with refrigeration dehumidifiers.

Absorption/desiccant dehumidification[edit]

This process uses adesiccant(humidity-absorbing material) to absorb moisture. The saturated material is then moved and the collected moisture is discharged, typically via heating.^[7]^[5]

Dehumidifiers that work according to the absorption principle are well-suited for high humidity at low temperatures. They are often used in industry to achieve humidity levels below 35%.

Because of the absence of compressor parts, desiccant dehumidifiers are often lighter and quieter than compressor dehumidifiers. Desiccant dehumidifiers can operate at lower temperatures as the unit does not need cooled coils.

Initial installation costs have limited the acceptance of desiccant dehumidification, worsened by lack of understanding of operational benefits, lack of technology awareness, and company priorities.^[8]

The AirJoule system uses ametal-organic framework(MOF) whose pores are sized to fit water molecules. It can absorb 55% of its weight in water. It consists of two chambers that take turns at dehumidifying. While one chamber dries air, the other releases moisture as liquid water. Heat from the drying chamber encourages the MOF to discharge its contents. The cavities swap roles every 10 minutes or so. Researchers claime that AirJoule consumes less than 100 watt-hours per liter of water vapor, cutting the energy required for dehumidification by as much as 90%. By contrast, Blue Frontier uses a liquid salt desiccant.^[9]

Membrane dehumidification[edit]

Several approaches can remove water vapor by flowing air past a membrane that allows vapor to enter.^[10]Dehumidification with membranes can allow for water vapor removal without condensation; this avoids the energy required with the enthalpy of vaporization, offering high efficiency for well-designed systems. Such dehumidification can be done passively with a rejected air stream; seeEnergy recovery ventilation.Active systems can use pressure gradients or electrocatalytic approaches.

Selective membrane dehumidification[edit]

Selective membranes use materials that block other ambient gases besides water vapor. Water vapor will then diffuse through these membranes under a concentration difference. Such a difference in concentration (partial pressure) can be caused by vacuum pumping, or simply passing by an airstream with a lower concentration of water. The most efficient configurations save energy by using two membranes that isolate a vacuum pump from ambient air.^[11]This dramatically reduces the pressure across the vacuum pump, saving energy. While such systems are often termed "Isothermal Membrane Dehumidification," recent research has shown that these systems can be made more efficient by combining them with heat exchange.^[12]Such integration can improve performance by improving the vapor compression cycle's COP (by operating between closer temperatures),^[13]and enhancing air mixing near the membrane.^[14]

Selective membranes can be made by immobilizing a liquid that can absorb water (or another solute) within a membranes, dubbed "supported liquid membranes".^[15]Typically, there are two layer types; a highly porous membrane that contains the absorbing liquid, and a trapping layer that prevents the liquid from escaping. This liquid absorbing layer allows them to behave like selective membranes, without having a solid selective materials or very small pores. The liquids within which absorbs water well (hygroscopic) may includeglycolmixtures or ionic liquids.

Ionic membrane dehumidification[edit]

An ionic membrane can be used to move humidity into or out of a sealed enclosure, using chemical reactions rather than condensation or selective materials. These systems use electrodes and proton-conducting membranes to remove water vapor byelectrolysis.At the anode,H₂Ois split into protons, O₂,and electrons, where the protons travel through a material and react with ambient oxygen on the other side to create water again.^[16]

Perhaps the first materials for such electrolysis-based dehumidification were solid polymer electrolyte (SPE) membranes. This approach provides a low power, steady-state dehumidifier for enclosed areas where long-term maintenance is difficult. This electrolytic process delivers dehumidifying capacities ranging from 0.2 grams/day from a 0.2 m³ (7 cu ft) space to 58 grams/day from an 8m³ (280 cu ft). SPE systems generally do not have high dehydration capacities, but because the water vapor is removed through electrolysis, the process is maintenance-free. The process also uses very little electrical energy to operate, requiring no moving parts, making the ionic membranes silent in operation and very reliable over long periods of time. SPE dehumidifiers are typically used to protect sensitive electrical components, medical equipment, museum specimens, or scientific apparatus from humid environments.

The SPE consists of a proton-conductive solid polymer electrolyte and porous electrodes with a catalytic layer composed of noble metal particles.^[17]When a voltage is applied to the porous electrode attached to the membrane, the moisture on theanodeside (dehumidifying side) dissociates into hydrogen ions (H+) and oxygen. The hydrogen ions migrate through membrane to be discharged on the cathode (moisture discharging) side where they react with oxygen in the air, resulting in water molecules (vapor), being discharged.^[18]Oxygen is released from the dehumidifying side, and if a large amount of water has been introduced to an airtight enclosure then oxygen can build up inside the enclosure.

Condensate[edit]

Not all dehumidifiers collect condensate; for example, many desiccant types discharge an airflow from the heated desiccant which contains water-saturated air. This can either be recondensed and collected as condensate, or expelled outside. Also, some air conditioner types spray any collected condensate onto the exterior condenser coils to cool it by evaporation, improving overall efficiency.

Disposal[edit]

Products using condensation technology have traditionally used a cold surface where humidity in warm air is condensed. Today, warm condensation technology, based on the concept of over-saturated steam inside a closed environment,^{[clarification needed]}makes it possible to dehumidify air at sub-zero temperatures. This is a very energy-efficient technology and equally efficient in all temperatures.

Most portable dehumidifiers are equipped with a condensate collection receptacle, typically with afloat sensorthat detects when the collection vessel is full, to shut off the dehumidifier and prevent an overflow of collected water. In a warm humid environment, these buckets will generally fill with water in 8–12 hours, and may need to be manually emptied and replaced several times per day to ensure continued operation.

Many portable dehumidifiers can also be adapted to connect the condensate drip output directly to a drain via a hose. Some dehumidifier models can tie into plumbing drains or use a built-in water pump to empty themselves as they collect moisture. Alternatively, a separatecondensate pumpmay be used to move collected water to a disposal location, when gravity drainage is not possible.

Central air conditioningunits typically need to be connected to a drain, because frequent manual emptying of multiple containers of condensate water extracted by such systems is impractical. If the condensate water is directed into the sewer system, it should be suitablytrappedto prevent septic odors and sewer gases from entering the building. The condensate should not be directed into aseptic systemof a house, because it does not need special treatment aseffluent.When the height of theair handler(containing the evaporator) is above the level of the surface drains used for rainwater, the condensate drain lines can often be routed into them. Air handlers located below grade level, e.g. the basement of a house, may need to use a condensate pump to lift the water to a surface drain.

Potability[edit]

Generally, dehumidifier water is considered a rather clean kind ofgreywater:not suitable for drinking, but acceptable for watering plants, though not garden vegetables.^[19]The health concerns are:^[19]^{[better source needed]}

The water contains trace metals from the heat exchanger, such ascopperandaluminum,orzincfrom galvanized steel supporting the frame and drain pan. Condensate would only be exposed to tin-leadsolderin copper drain pipe, but theleadcontent is particularly dangerous. Trace metals may pose a danger if used on edible plants, as they canbioaccumulate.However, the water is considered usable forirrigationof ornamental plants and lawns.
Variouspathogens,includingfungal spores,may accumulate in the water, particularly due to its stagnancy. Unlike indistilled waterproduction, the water is not boiled, which would kill pathogens (including bacteria).
As with distilled water, beneficial minerals are largely absent.

Food-grade dehumidifiers, also calledatmospheric water generators,are specifically designed to avoid toxic metal contamination and to keep all water contact surfaces clean. The devices are primarily intended to produce pure water, and the dehumidifying effect is viewed as secondary to their operation.

Maintenance[edit]

If condensate water is handled automatically, most dehumidifiers require very little maintenance. Because of the volume of airflow through the appliance, dust buildup needs to be removed so it does not impede airflow; many designs feature removable and washable air filters. Condensate collection trays and containers may need occasional cleaning to remove debris buildup and prevent clogging of drainage passages, which can cause water leakage and overflow; if large amounts of certain particulates or dust are collected, then this may need to be performed frequently to avoid microbial growth.

Applications[edit]

Relative humidity in dwellings should preferably range from 30% to 50%.^[20]

Homes and offices[edit]

Dehumidification within buildings can control:

excessive body perspiration buildup that cannot evaporate in moisture-saturated air
condensation dripping from cold-water pipes
warping and sticking of furniture and doors
moldandmildew,which can cause fabrics, books, and furnishings to develop mustiness
clothes moths,fleas,cockroaches,silverfish,woodlice,millipedes,anddust mites,which thrive in damp conditions (basements, crawl spaces, kitchens, bedrooms, bathrooms, spas or indoor pool areas, warehouses, workshops)

Construction[edit]

Dehumidifiers are also used in construction areas and renovations of indoor space to remove excess humidity or mildew.

Industrial processes[edit]

Dehumidifiers are used in industrialclimatic chambers,to reduce relative humidity and the dew point in many industrial applications from waste and fresh water treatment plants to indoor grow rooms where the control of moisture is essential.

Market size[edit]

According to a 2015 estimate, the projected annual globaltotal addressable marketof dehumidifiers was about $3.5 billion by 2022. This includes various types and applications, encompassing different applications such as household and industrial and different technologies such as ventilating and desiccant.^[21]

References[edit]

^^a ^bNagengast, Bernard (June 2002). "100 Years of Air Conditioning".ASHRAE Journal.44(6).ASHRAE:44–46.CiteSeerX10.1.1.545.9425.ISSN 0001-2491.
^Lagarda, Patxi; Theiler, Jeff; Kovacs, Zoltan; Botta, Charles R.; Zagaynov, Mikhail; Descloux, Antoine; Varho, Manu (April 2016). Bogomoloff, Harry (ed.).IIHF Ice Rink Guide(PDF)(revised ed.).International Ice Hockey Federation.p. 28.RetrievedMay 8,2021.
^Harriman III, Lewis G.; Plager, Dean; Kosar, Douglas (November 1997)."Dehumidification and cooling loads from ventilation air"(PDF).ASHRAE Journal.39(11).New York City:ASHRAE:37–45.doi:10.1080/01998595.1999.10530479.ISSN 0001-2491.OSTI 563883– via Taylor & Francis Online.
^Cheung, Caroline (2021). "Managing food storage in the Roman Empire".Quaternary International.597.Elsevier BV: 63–75.Bibcode:2021QuInt.597...63C.doi:10.1016/j.quaint.2020.08.007.ISSN 1040-6182.
^^a ^bHawaii Energy and Environmental Technologies (HEET) Initiative.July 2016.
^Zhang, Zheng; Chen, Bingbin; Lu, Congda; Wu, Helong; Wu, Huaping; Jiang, Shaofei; Chai, Guozhong (2017)."A novel thermo-mechanical anti-icing/de-icing system using bi-stable laminate composite structures with superhydrophobic surface"(PDF).Composite Structures.180.Elsevier BV: 933–943.doi:10.1016/j.compstruct.2017.08.068.ISSN 0263-8223.
^Sajesh, M.; Fekadu, Geleta; Kalpana; Subudhi, Sudhakar (November 2021). "Liquid Desiccant Air Conditioning Using Single Storage Solution Tank, Evaporative Cooling, and Marquise-Shaped Solar Collector".Journal of Energy Resources Technology.143(11).American Society of Mechanical Engineers.doi:10.1115/1.4049604.ISSN 0195-0738.S2CID 235514861.
^Hawaii Energy and Environmental Technologies (HEET) Initiative.
^Baraniuk, Chris."Cutting-Edge Technology Could Massively Reduce the Amount of Energy Used for Air Conditioning".Wired.ISSN 1059-1028.Retrieved2024-07-18.
^Labban, Omar; Chen, Tianyi; Ghoniem, Ahmed F.; Lienhard, John H.; Norford, Leslie K. (2017)."Next-generation HVAC: Prospects for and limitations of desiccant and membrane-based dehumidification and cooling".Applied Energy.200.Elsevier BV: 330–346.Bibcode:2017ApEn..200..330L.doi:10.1016/j.apenergy.2017.05.051.hdl:1721.1/110727.ISSN 0306-2619.
^"US8500848B2 - Systems and methods for air dehumidification and cooling with membrane water vapor rejection".Google Patents.2011-11-11.Retrieved2022-03-30.
^Fix, Andrew J.; Pamintuan, Bryan C.; Braun, James E.; Warsinger, David M. (2022). "Vapor-selective active membrane energy exchanger with mechanical ventilation and indoor air recirculation".Applied Energy.312.Elsevier BV: 118768.Bibcode:2022ApEn..31218768F.doi:10.1016/j.apenergy.2022.118768.ISSN 0306-2619.S2CID 247215756.
^Fix, Andrew J.; Braun, James E.; Warsinger, David M. (2021). "Vapor-selective active membrane energy exchanger for high efficiency outdoor air treatment".Applied Energy.295.Elsevier BV: 116950.Bibcode:2021ApEn..29516950F.doi:10.1016/j.apenergy.2021.116950.ISSN 0306-2619.S2CID 236240612.
^Chandrasekaran, Ajay Sekar; Fix, Andrew J.; Warsinger, David M. (2022-03-22)."Combined Membrane Dehumidification with Heat Exchangers Optimized Using CFD for High Efficiency HVAC Systems".Membranes.12(4): 348.doi:10.3390/membranes12040348.ISSN 2077-0375.PMC9029657.PMID 35448318.
^Imato, Toshihiko; Ogawa, Hosei; Morooka, Shigeharu; Kato, Yasuo (1981-08-20)."Transport Of Copper(Ii) Through Supported Liquid Membrane Containing LIX65N".Journal of Chemical Engineering of Japan(in Japanese).14(4): 289–295.doi:10.1252/jcej.14.289.ISSN 0021-9592.S2CID 97244892.Retrieved2022-03-11.
^Yamauchi, S. (2000). "Application of a hydrogen reference electrode to a solid state water removal device".Journal of Applied Electrochemistry.30(11). Springer Science and Business Media LLC: 1235–1241.doi:10.1023/a:1026543510297.ISSN 0021-891X.S2CID 91569378.
^"How does Rosahl work?".Rosahl.Westside International Ltd. August 19, 2015.Archivedfrom the original on 2018-09-21.RetrievedMay 8,2021.
^Sakuma, Shuichi; Yamauchi, Shiro; Takai, Osamu (December 2010). "Estimation of dehumidifying performance of solid polymer electrolytic dehumidifier for practical application".Journal of Applied Electrochemistry.40(12).Springer Nature:2153–2160.doi:10.1007/s10800-010-0197-4.ISSN 0021-891X.S2CID 96211880– via SpringerLink.
^^a ^bLaumer, John (July 29, 2005)."Can I Water My Plants With It?".TreeHugger.Archived fromthe originalon March 18, 2019.RetrievedMay 8,2021.
^"Dehumidifier Basics".Energy Star.Archivedfrom the original on 2016-02-27.RetrievedMay 8,2021.
^"Dehumidifier Market Size to Reach $3.54 Billion by 2022".Air Conditioning, Heating & Refrigeration News.San Francisco:BNP Media. October 28, 2015.Retrieved16 September2019.

v t e Heating, ventilation, and air conditioning
Fundamental concepts	Air changes per hour Bake-out Building envelope Convection Dilution Domestic energy consumption Enthalpy Fluid dynamics Gas compressor Heat pump and refrigeration cycle Heat transfer Humidity Infiltration Latent heat Noise control Outgassing Particulates Psychrometrics Sensible heat Stack effect Thermal comfort Thermal destratification Thermal mass Thermodynamics Vapour pressure of water
Technology	Absorption-compression heat pump Absorption refrigerator Air barrier Air conditioning Antifreeze Automobile air conditioning Autonomous building Building insulation materials Central heating Central solar heating Chilled beam Chilled water Constant air volume(CAV) Coolant Cross ventilation Dedicated outdoor air system(DOAS) Deep water source cooling Demand controlled ventilation(DCV) Displacement ventilation District cooling District heating Electric heating Energy recovery ventilation(ERV) Firestop Forced-air Forced-air gas Free cooling Heat recovery ventilation(HRV) Hybrid heat Hydronics Ice storage air conditioning Kitchen ventilation Mixed-mode ventilation Microgeneration Passive cooling Passive daytime radiative cooling Passive house Passive ventilation Radiant heating and cooling Radiant cooling Radiant heating Radon mitigation Refrigeration Renewable heat Room air distribution Solar air heat Solar combisystem Solar cooling Solar heating Thermal insulation Thermosiphon Underfloor air distribution Underfloor heating Vapor barrier Vapor-compression refrigeration(VCRS) Variable air volume(VAV) Variable refrigerant flow(VRF) Ventilation Water heat recycling
Components	Air conditioner inverter Air door Air filter Air handler Air ionizer Air-mixing plenum Air purifier Air source heat pump Attic fan Automatic balancing valve Back boiler Barrier pipe Blast damper Boiler Centrifugal fan Ceramic heater Chiller Condensate pump Condenser Condensing boiler Convection heater Compressor Cooling tower Damper Dehumidifier Duct Economizer Electrostatic precipitator Evaporative cooler Evaporator Exhaust hood Expansion tank Fan Fan coil unit Fan filter unit Fan heater Fire damper Fireplace Fireplace insert Freeze stat Flue Freon Fume hood Furnace Gas compressor Gas heater Gasoline heater Grease duct Grille Ground-coupled heat exchanger Ground source heat pump Heat exchanger Heat pipe Heat pump Heating film Heating system HEPA High efficiency glandless circulating pump High-pressure cut-off switch Humidifier Infrared heater Inverter compressor Kerosene heater Louver Mechanical room Oil heater Packaged terminal air conditioner Plenum space Pressurisation ductwork Process duct work Radiator Radiator reflector Recuperator Refrigerant Register Reversing valve Run-around coil Sail switch Scroll compressor Solar chimney Solar-assisted heat pump Space heater Smoke canopy Smoke damper Smoke exhaust ductwork Thermal expansion valve Thermal wheel Thermostatic radiator valve Trickle vent Trombe wall TurboSwing Turning vanes Ultra-low particulate air(ULPA) Whole-house fan Windcatcher Wood-burning stove Zone valve
Measurement and control	Air flow meter Aquastat BACnet Blower door Building automation Carbon dioxide sensor Clean air delivery rate(CADR) Control valve Gas detector Home energy monitor Humidistat HVAC control system Infrared thermometer Intelligent buildings LonWorks Minimum efficiency reporting value(MERV) Normal temperature and pressure(NTP) OpenTherm Programmable communicating thermostat Programmable thermostat Psychrometrics Room temperature Smart thermostat Standard temperature and pressure(STP) Thermographic camera Thermostat Thermostatic radiator valve
Professions, trades, and services	Architectural acoustics Architectural engineering Architectural technologist Building services engineering Building information modeling(BIM) Deep energy retrofit Duct cleaning Duct leakage testing Environmental engineering Hydronic balancing Kitchen exhaust cleaning Mechanical engineering Mechanical, electrical, and plumbing Mold growth, assessment, and remediation Refrigerant reclamation Testing, adjusting, balancing
Industry organizations	AHRI AMCA ASHRAE ASTM International BRE BSRIA CIBSE Institute of Refrigeration IIR LEED SMACNA UMC
Health and safety	Indoor air quality(IAQ) Passive smoking Sick building syndrome(SBS) Volatile organic compound(VOC)
See also	ASHRAE Handbook Building science Fireproofing Glossary of HVAC terms Warm Spaces World Refrigeration Day Template:Home automation Template:Solar energy

v t e Plumbing
Fundamental concepts	Air gap (plumbing) Backflow Compatibility (chemical) Corrosion Drain (plumbing) Drinking water Fuel gas Friction loss Grade (slope) Greywater Heat trap Hydrostatic loop Leak Neutral axis Onsite sewage facility Pressure Sanitary sewer Sewer gas Sewage Sewerage Siphon Storm sewer Stormwater Surface tension Tap water Thermal expansion Thermal insulation Thermosiphon Trap (plumbing) Venturi effect Wastewater Water hammer Water supply network Water table Well
Technology	Brazing British Standard Pipe(BSP) Cast iron pipe Chemical drain cleaners Compression fitting Copper tubing Crimp (joining) Drain-waste-vent system Ductile iron pipe Flare fitting Garden Hose Thread(GHT) Gasket Hydronics Leak detection National Pipe Thread(NPT) Nominal Pipe Size(NPS) O-ring Oakum Pipe (fluid conveyance) Pipe dope Pipe support Plastic pipework Push-to-pull compression fittings Putty Sealant Sewage pumping Soldering Solvent welding Swaging Thread seal tape Threaded pipe Tube bending Water heat recycling
Components	Atmospheric vacuum breaker Automatic bleeding valve Automatic faucet Backflow prevention device Ball valve Bleed screw Booster pump Butterfly valve Check valve Chemigation valve Chopper pump Circulator pump Cistern Closet flange Concentric reducer Condensate pump Coupling (piping) Diaphragm valve Dielectric union Double check valve Eccentric reducer Expansion tank Faucet aerator Float switch Float valve Floor drain Flow limiter Flushing trough Flushometer Gate valve Globe valve Grease trap Grinder pump Hose coupling Manifold Needle valve Nipple (plumbing) Pinch valve Piping and plumbing fitting Plug (sanitation) Pressure regulator Pressure vacuum breaker Pressure-balanced valve Pump Radiator (heating) Reduced pressure zone device Reducer Relief valve Riser clamp Rooftop water tower Safety valve Sewage pump Street elbow Submersible pump Tap (valve) Thermostatic mixing valve Trench drain Vacuum breaker Vacuum ejector Valve Water tank Zone valve
Plumbing fixtures	Accessible bathtub Bathtub Bidet Dehumidifier Dishwasher Drinking fountain Electric water boiler Evaporative cooler Flush toilet Garbage disposal unit Hot water storage tank Humidifier Icemaker Instant hot water dispenser Laundry tub Shower Sink Storage water heater Sump pump Tankless water heater Urinal Washing machine Washlet Water dispenser Water filter Water heater Water softener
Specialized tools	Basin wrench Blowtorch Borescope Core drill Drain cleaner Driving cap Flare-nut wrench Pipecutter Pipe wrench Plumber's snake Plumber wrench Plunger Strap wrench Tap and die
Measurement and control	Control valve Flow sensor Pressure sensor Water detector Water metering
Professions, trades, and services	Hydronic balancing Hydrostatic testing Leak detection Mechanical, electrical, and plumbing Pipe marking Pipefitter Pipelayer Plumber
Industry organizations and standards	International Association of Plumbing and Mechanical Officials (IAPMO) NSF International Plumbing & Drainage Institute (PDI) Uniform Plumbing Code (UPC) World Plumbing Council (WPC)
Health and safety	Plumbing code Scalding Waterborne disease
See also	Fire sprinkler system Piping Template:HVAC Template:Public health Template:Sewerage Template:Toilets Template:Wastewater