Jump to content

Poly(methyl methacrylate)

From Wikipedia, the free encyclopedia
(Redirected fromPlexiglass)
This article is about the transparent plastic sometimes called acrylic glass. For the glass/plastic laminate often called "safety glass", seeLaminated glass.For the neurotoxic designer drug PMMA, seepara-Methoxy-N-methylamphetamine.For other uses, seeAcrylic (disambiguation).
Poly(methyl methacrylate)
Names
IUPAC name
Poly(methyl 2-methylpropenoate)
Other names
  • Poly(methyl methacrylate)
  • PMMA
  • Methyl methacrylate resin
  • Perspex
Identifiers
3D model (JSmol)
ChemSpider
  • None
ECHA InfoCard 100.112.313Edit this at Wikidata
KEGG
UNII
  • CCC(C)(C(=O)OC)CC(C)(C(=O)OC)CC(C)(C(=O)OC)CC(C)(C(=O)OC)CC(C)(C(=O)OC)C
Properties
(C5H8O2)n
Molar mass Varies
Density 1.18g/cm3[1]
−9.06×10−6(SI, 22°C)[2]
1.4905 at 589.3nm[3]
Except where otherwise noted, data are given for materials in theirstandard state(at 25 °C [77 °F], 100 kPa).
Lichtenberg figure:high-voltage dielectric breakdown in an acrylic polymer block

Poly(methyl methacrylate) (PMMA) is thesynthetic polymerderived frommethyl methacrylate.It is used as anengineering plastic,and it is atransparentthermoplastic.PMMA is also known asacrylic,acrylic glass,as well as by the trade names and brandsCrylux,Hesalite,Plexiglas,Acrylite,Lucite,andPerspex,among several others (see below). This plastic is often used in sheet form as a lightweight or shatter-resistant alternative toglass.It can also be used as a casting resin, in inks and coatings, and for many other purposes.

It is often technically classified as a type ofglass,in that it is a non-crystalline vitreous substance—hence its occasional historic designation asacrylic glass.

History

[edit]

The first acrylic acid was created in 1843.Methacrylic acid,derived fromacrylic acid,was formulated in 1865. The reaction between methacrylic acid andmethanolresults in the ester methyl methacrylate.

It was developed in 1928 in several different laboratories by many chemists, such as William R. Conn,Otto Röhm,and Walter Bauer, and first brought to market in 1933 by GermanRöhm & Haas AG(as of January 2019, part ofEvonik Industries) and its partner and former U.S. affiliateRohm and Haas Companyunder thetrademarkPlexiglas.[4]

Polymethyl methacrylate was discovered in the early 1930s by British chemists Rowland Hill and John Crawford atImperial Chemical Industries(ICI) in the United Kingdom.[citation needed]ICI registered the product under the trademark Perspex. About the same time, chemist and industrialistOtto Röhmof Röhm and Haas AG in Germany attempted to produce safety glass by polymerizing methyl methacrylate between two layers of glass. The polymer separated from the glass as a clear plastic sheet, which Röhm gave the trademarked name Plexiglas in 1933.[5]Both Perspex and Plexiglas were commercialized in the late 1930s. In the United States, E.I. du Pont de Nemours & Company (now DuPont Company) subsequently introduced its own product under the trademark Lucite. In 1936 ICI Acrylics (now Lucite International) began the first commercially viable production of acrylic safety glass. DuringWorld War IIboth Allied and Axis forces used acrylic glass for submarine periscopes and aircraft windscreen, canopies, and gun turrets. Scraps of acrylic were also used to made clear pistol grips for the M1911A1 pistol or clear handle grips for the M1 bayonet or theater knifes so that soldiers could put small photos of loved ones or pin-up girls' pictures inside. The were called "Sweetheart Grips" or "Pin-up Grips". Others were used to make handles for theater knives made from scrap materials and people who made them got artistic or creative.[6]Civilian applications followed after the war.[7]

Names

[edit]

Common orthographic stylings includepolymethyl methacrylate[8][9]andpolymethylmethacrylate.The full IUPAC chemical name is poly(methyl 2-methylpropenoate). (It is a common mistake to use "an" instead of "en".)

Although PMMA is often called simply "acrylic",acryliccan also refer to other polymers or copolymers containingpolyacrylonitrile.Notable trade names and brands include Acrylite, Altuglas,[10]Astariglas, Cho Chen, Crystallite, Cyrolite,[11]Hesalite (when used inOmega watches), Lucite,[12]Optix,[11]Oroglas,[13]PerClax, Perspex,[11]Plexiglas,[11][14]R-Cast, and Sumipex.

PMMA is an economical alternative topolycarbonate(PC) whentensile strength,flexural strength,transparency,polishability, and UV tolerance are more important thanimpact strength,chemical resistance, and heat resistance. Additionally, PMMA does not contain the potentially harmfulbisphenol-Asubunits found in polycarbonate and is a far better choice for laser cutting.[15]It is often preferred because of its moderate properties, easy handling and processing, and low cost. Non-modified PMMA behaves in a brittle manner when under load, especially under animpact force,and is more prone to scratching than conventional inorganic glass, but modified PMMA is sometimes able to achieve high scratch and impact resistance.

Properties

[edit]
Skeletal structure of methyl methacrylate, the constituentmonomerof PMMA
Pieces of Plexiglas taken from the windscreen of a German plane shot down during World War II

PMMA is a strong, tough, and lightweight material. It has adensityof 1.17–1.20 g/cm3,[1][16]which is less than half that of glass.[1]It also has good impact strength, higher than both glass and polystyrene, but significantly lower than polycarbonate and some engineered polymers. PMMA ignites at 460 °C (860 °F) andburns,formingcarbon dioxide,water,carbon monoxide,and low-molecular-weight compounds, includingformaldehyde.[17]

PMMAtransmitsup to 92% ofvisible light(3 mm (0.12 in) thickness),[18]and gives a reflection of about 4% from each of its surfaces due to itsrefractive index(1.4905 at 589.3nm).[3]It filtersultraviolet(UV) light at wavelengths below about 300nm(similar to ordinary window glass). Some manufacturers[19]add coatings or additives to PMMA to improve absorption in the 300–400 nm range. PMMA passesinfraredlight of up to 2,800 nm and blocks IR of longerwavelengthsup to 25,000 nm. Colored PMMA varieties allow specific IR wavelengths to pass while blockingvisible light(forremote controlor heat sensor applications, for example).

PMMA swells and dissolves in many organicsolvents;it also has poor resistance to many other chemicals due to its easilyhydrolyzedestergroups. Nevertheless, its environmental stability is superior to most other plastics such as polystyrene and polyethylene, and therefore it is often the material of choice for outdoor applications.[20]

PMMA has a maximum water absorption ratio of 0.3–0.4% by weight.[16]Tensile strength decreases with increased water absorption.[21]Itscoefficient of thermal expansionis relatively high at (5–10)×10−5°C−1.[22]

TheFuturohouse was made of fibreglass-reinforced polyester plastic, polyester-polyurethane, and poly(methylmethacrylate); one of them was found to be degrading bycyanobacteriaandArchaea.[23][24]

PMMA can be joined usingcyanoacrylatecement (commonly known assuperglue), with heat (welding), or by using chlorinated solvents such asdichloromethaneortrichloromethane[25](chloroform) to dissolve the plastic at the joint, which then fuses and sets, forming an almost invisibleweld.Scratches may easily be removed by polishing or by heating the surface of the material.Laser cuttingmay be used to form intricate designs from PMMA sheets. PMMA vaporizes to gaseous compounds (including its monomers) upon laser cutting, so a very clean cut is made, and cutting is performed very easily. However, the pulsed lasercutting introduces high internal stresses, which on exposure to solvents produce undesirable "stress-crazing"at the cut edge and several millimetres deep. Even ammonium-based glass-cleaner and almost everything short of soap-and-water produces similar undesirable crazing, sometimes over the entire surface of the cut parts, at great distances from the stressed edge.[26]Annealing the PMMA sheet/parts is therefore an obligatory post-processing step when intending to chemically bond lasercut parts together.

In the majority of applications, PMMA will not shatter. Rather, it breaks into large dull pieces. Since PMMA is softer and more easily scratched than glass,scratch-resistant coatingsare often added to PMMA sheets to protect it (as well as possible other functions).

Pure poly(methyl methacrylate) homopolymer is rarely sold as an end product, since it is not optimized for most applications. Rather, modified formulations with varying amounts of othercomonomers,additives, and fillers are created for uses where specific properties are required. For example:

  • A small amount of acrylate comonomers are routinely used in PMMA grades destined for heat processing, since this stabilizes the polymer todepolymerization( "unzipping" ) during processing.
  • Comonomers such asbutyl acrylateare often added to improve impact strength.
  • Comonomers such as methacrylic acid can be added to increase the glass transition temperature of the polymer for higher temperature use such as in lighting applications.
  • Plasticizersmay be added to improve processing properties, lower the glass transition temperature, improve impact properties, and improve mechanical properties such as elastic modulus[27]
  • Dyesmay be added to give color for decorative applications, or to protect against (or filter) UV light.
  • Fillersmay be substituted to reduce cost.

Synthesis and processing

[edit]

PMMA is routinely produced byemulsion polymerization,solution polymerization,andbulk polymerization.Generally, radical initiation is used (includingliving polymerizationmethods), but anionic polymerization of PMMA can also be performed.[28]

Theglass transition temperature(Tg) ofatacticPMMA is 105 °C (221 °F). TheTgvalues of commercial grades of PMMA range from 85 to 165 °C (185 to 329 °F); the range is so wide because of the vast number of commercial compositions that are copolymers with co-monomers other than methyl methacrylate. PMMA is thus an organic glass at room temperature; i.e., it is below itsTg.The forming temperature starts at the glass transition temperature and goes up from there.[29]All common molding processes may be used, includinginjection molding,compression molding,andextrusion.The highest quality PMMA sheets are produced bycell casting,but in this case, the polymerization and molding steps occur concurrently. The strength of the material is higher than molding grades owing to its extremely highmolecular mass.Rubber tougheninghas been used to increase the toughness of PMMA to overcome its brittle behavior in response to applied loads.

Applications

[edit]
Close-up of pressure sphere of thebathyscapheTrieste,with a single conical window of PMMA set into sphere hull. The very small black circle (smaller than the man's head) is the inner side of the plastic "window", only a few inches in diameter. The larger circular clear black area represents the larger outer side of the thick one-piece plastic cone "window".

Being transparent and durable, PMMA is a versatile material and has been used in a wide range of fields and applications such as rear-lights and instrument clusters for vehicles, appliances, and lenses for glasses. PMMA in the form of sheets affords to shatter resistant panels for building windows, skylights, bulletproof security barriers, signs and displays, sanitary ware (bathtubs), LCD screens, furniture and many other applications. It is also used for coating polymers based on MMA provides outstanding stability against environmental conditions with reduced emission of VOC. Methacrylate polymers are used extensively in medical and dental applications where purity and stability are critical to performance.[28]

Glass substitute

[edit]
10-meter (33 ft) deepMonterey Bay Aquariumtank has acrylic windows up to 33 centimeters (13 in) thick to withstand thewater pressure.
  • PMMA is commonly used for constructing residential and commercialaquariums.Designers started building large aquariums when poly(methyl methacrylate) could be used. It is less often used in other building types due to incidents such as theSummerland disaster.
  • PMMA is used for viewing ports and even complete pressure hulls of submersibles, such as theAliciasubmarine's viewing sphere and the window of thebathyscaphe Trieste.
  • PMMA is used in the lenses of exterior lights of automobiles.[30]
  • Spectator protection inice hockeyrinks is made from PMMA.
  • Historically, PMMA was an important improvement in the design of aircraft windows, making possible such designs as the bombardier's transparent nose compartment in theBoeing B-17 Flying Fortress.Modern aircraft transparencies often use stretched acrylic plies.
  • Police vehicles forriot controloften have the regular glass replaced with PMMA to protect the occupants from thrown objects.
  • PMMA is an important material in the making of certain lighthouse lenses.[31]
  • PMMA was used for the roofing of the compound in theOlympic Parkfor the1972 Summer Olympicsin Munich. It enabled a light and translucent construction of the structure.[32]
  • PMMA (under the brand name "Lucite" ) was used for the ceiling of theHouston Astrodome.

Daylight redirection

[edit]
Main article:Anidolic lighting
  • Laser cut acrylic panels have been used to redirect sunlight into alight pipeor tubular skylight and, from there, to spread it into a room.[33]Their developers Veronica Garcia Hansen,Ken Yeang,and Ian Edmonds were awarded theFar East Economic Review Innovation Awardin bronze for this technology in 2003.[34][35]
  • Attenuation being quite strong for distances over one meter (more than 90% intensity loss for a 3000 K source),[36]acrylic broadband light guides are then dedicated mostly to decorative uses.
  • Pairs of acrylic sheets with a layer of microreplicated prisms between the sheets can have reflective and refractive properties that let them redirect part of incoming sunlight in dependence on itsangle of incidence.Such panels act as miniaturelight shelves.Such panels have been commercialized for purposes ofdaylighting,to be used as awindowor acanopysuch that sunlight descending from the sky is directed to the ceiling or into the room rather than to the floor. This can lead to a higher illumination of the back part of a room, in particular when combined with a white ceiling, while having a slight impact on the view to the outside compared to normal glazing.[37][38]

Medicine

[edit]
  • PMMA has a good degree of compatibility with humantissue,and it is used in the manufacture of rigidintraocular lenseswhich are implanted in theeyewhen the original lens has been removed in the treatment ofcataracts.This compatibility was discovered by the English ophthalmologistHarold Ridleyin WWII RAF pilots, whose eyes had been riddled with PMMA splinters coming from the side windows of their SupermarineSpitfirefighters – the plastic scarcely caused any rejection, compared to glass splinters coming from aircraft such as theHawker Hurricane.[39]Ridley had a lens manufactured by the Rayner company (Brighton & Hove, East Sussex) made from Perspex polymerised by ICI. On 29 November 1949 at St Thomas' Hospital, London, Ridley implanted the first intraocular lens at St Thomas's Hospital in London.[40]

In particular, acrylic-type lenses are useful for cataract surgery in patients that have recurrent ocular inflammation (uveitis), as acrylic material induces less inflammation.

  • Eyeglasslenses are commonly made from PMMA.
  • Historically, hardcontact lenseswere frequently made of this material. Soft contact lenses are often made of a related polymer, where acrylate monomers containing one or morehydroxyl groupsmake themhydrophilic.
  • Inorthopedic surgery,PMMAbone cementis used to affix implants and to remodel lost bone.[41]It is supplied as a powder with liquid methyl methacrylate (MMA). Although PMMA is biologically compatible, MMA is considered to be an irritant and a possiblecarcinogen.PMMA has also been linked tocardiopulmonaryevents in the operating room due tohypotension.[42]Bone cement acts like agroutand not so much like a glue inarthroplasty.Although sticky, it does not bond to either the bone or the implant; rather, it primarily fills the spaces between the prosthesis and the bone preventing motion. A disadvantage of this bone cement is that it heats up to 82.5 °C (180.5 °F) while setting that may cause thermal necrosis of neighboring tissue. A careful balance of initiators and monomers is needed to reduce the rate of polymerization, and thus the heat generated.
  • Incosmetic surgery,tiny PMMA microspheres suspended in some biological fluid are injected as a soft-tissue filler under the skin to reduce wrinkles or scars permanently.[43]PMMA as a soft-tissue filler was widely used in the beginning of the century to restore volume in patients with HIV-related facial wasting. PMMA is used illegally to shape muscles by somebodybuilders.
  • Plombageis an outdated treatment oftuberculosiswhere thepleuralspace around an infectedlungwas filled with PMMA balls, in order to compress and collapse the affected lung.
  • Emerging biotechnology andbiomedical researchuse PMMA to createmicrofluidiclab-on-a-chipdevices, which require 100 micrometre-wide geometries for routing liquids. These small geometries are amenable to using PMMA in abiochipfabrication process and offers moderatebiocompatibility.
  • Bioprocesschromatographycolumns use cast acrylic tubes as an alternative to glass and stainless steel. These are pressure rated and satisfy stringent requirements of materials forbiocompatibility,toxicity, and extractables.

Dentistry

[edit]

Due to its aforementioned biocompatibility, poly(methyl methacrylate) is a commonly used material in modern dentistry, particularly in the fabrication of dental prosthetics, artificial teeth, and orthodontic appliances.

  • Acrylic prosthetic construction: Pre-polymerized, powdered PMMA spheres are mixed with a Methyl Methacrylate liquid monomer, Benzoyl Peroxide (initiator), and NN-Dimethyl-P-Toluidine (accelerator), and placed under heat and pressure to produce a hardened polymerized PMMA structure. Through the use of injection molding techniques, wax based designs with artificial teeth set in predetermined positions built on gypsum stone models of patients' mouths can be converted into functional prosthetics used to replace missing dentition. PMMA polymer and methyl methacrylate monomer mix is then injected into a flask containing a gypsum mold of the previously designed prosthesis, and placed under heat to initiate polymerization process. Pressure is used during the curing process to minimize polymerization shrinkage, ensuring an accurate fit of the prosthesis. Though other methods of polymerizing PMMA for prosthetic fabrication exist, such as chemical and microwave resin activation, the previously described heat-activated resin polymerization technique is the most commonly used due to its cost effectiveness and minimal polymerization shrinkage.
  • Artificial teeth: While denture teeth can be made of several different materials, PMMA is a material of choice for the manufacturing of artificial teeth used in dental prosthetics. Mechanical properties of the material allow for heightened control of aesthetics, easy surface adjustments, decreased risk of fracture when in function in the oral cavity, and minimal wear against opposing teeth. Additionally, since the bases of dental prosthetics are often constructed using PMMA, adherence of PMMA denture teeth to PMMA denture bases is unparalleled, leading to the construction of a strong and durable prosthetic.[44]

Art and aesthetics

[edit]
LexusPerspex car sculpture
PMMA art byManfred Kielnhofer
Kawaiacrylic grand piano
Lucite Bangle Bracelet
  • Acrylic paintessentially consists of PMMA suspended in water; however since PMMA ishydrophobic,a substance with both hydrophobic and hydrophilic groups needs to be added to facilitate thesuspension.
  • Modernfurnituremakers, especially in the 1960s and 1970s, seeking to give their products a space age aesthetic, incorporated Lucite and other PMMA products into their designs, especially office chairs. Many other products (for example, guitars) are sometimes made with acrylic glass to make the commonly opaque objects translucent.
  • Perspex has been used as a surface to paint on, for example bySalvador Dalí.
  • Diasecis a process which uses acrylic glass as a substitute for normal glass inpicture frames.This is done for its relatively low cost, light weight, shatter-resistance, aesthetics and because it can be ordered in larger sizes than standardpicture framing glass.
  • As early as 1939, Los Angeles-based Dutch sculptorJan De Swartexperimented with samples of Lucite sent to him by DuPont; De Swart created tools to work the Lucite for sculpture and mixed chemicals to bring about certain effects of color and refraction.[45]
  • From approximately the 1960s onward, sculptors and glass artists such asJan Kubíček,Leroy Lamis,andFrederick Hartbegan using acrylics, especially taking advantage of the material's flexibility, light weight, cost and its capacity to refract and filter light.
  • In the 1950s and 1960s, Lucite was an extremely popular material for jewelry, with several companies specialized in creating high-quality pieces from this material. Lucite beads and ornaments are still sold by jewelry suppliers.
  • Acrylic sheets are produced in dozens of standard colors, most commonly sold using color numbers developed by Rohm & Haas in the 1950s.
See also:Acrylic embedment
Illustrative and securebrominechemical sample used for teaching. The glass sample vial of the corrosive and poisonous liquid has been cast into an acrylic plastic cube

Methyl methacrylate"synthetic resin"for casting (simply the bulk liquid chemical) may be used in conjunction with a polymerization catalyst such asmethyl ethyl ketone peroxide(MEKP), to produce hardened transparent PMMA in any shape, from a mold. Objects like insects or coins, or even dangerous chemicals in breakable quartz ampules, may be embedded in such "cast" blocks, for display and safe handling.

Other uses

[edit]
High-heel shoesmade of Lucite
An electricbass guitarmade from poly(methyl methacrylate)
AFuturohouse inWarrington, New Zealand
  • PMMA, in the commercial form Technovit 7200 is used vastly in the medical field. It is used for plastic histology, electron microscopy, as well as many more uses.
  • PMMA has been used to create ultra-white opaque membranes that are flexible and switch appearance to transparent when wet.[46]
  • Acrylic is used in tanning beds as the transparent surface that separates the occupant from the tanning bulbs while tanning. The type of acrylic used in tanning beds is most often formulated from a special type of polymethyl methacrylate, a compound that allows the passage of ultraviolet rays.
  • Sheets of PMMA are commonly used in the sign industry to make flat cut out letters in thicknesses typically varying from 3 to 25 millimeters (0.1 to 1.0 in). These letters may be used alone to represent a company's name and/or logo, or they may be a component of illuminated channel letters. Acrylic is also used extensively throughout the sign industry as a component of wall signs where it may be a backplate, painted on the surface or the backside, a faceplate with additional raised lettering or even photographic images printed directly to it, or a spacer to separate sign components.
  • PMMA was used inLaserdiscoptical media.[47](CDsandDVDsuse both acrylic and polycarbonate for impact resistance).
  • It is used as a light guide for the backlights inTFT-LCDs.[48]
  • Plastic optical fiberused for short-distance communication is made from PMMA, and perfluorinated PMMA, clad with fluorinated PMMA, in situations where its flexibility and cheaper installation costs outweigh its poor heat tolerance and higher attenuation versus glass fiber.
  • PMMA, in a purified form, is used as the matrix inlaser dye-doped organic solid-state gain media for tunablesolid state dye lasers.[49]
  • Insemiconductorresearch and industry, PMMA aids as aresistin theelectron beam lithographyprocess. A solution consisting of the polymer in a solvent is used tospin coatsiliconand other semiconducting and semi-insulating wafers with a thin film. Patterns on this can be made by an electron beam (using anelectron microscope), deep UV light (shorter wavelength than the standardphotolithographyprocess), orX-rays.Exposure to these creates chain scission or (de-cross-linking) within the PMMA, allowing for the selective removal of exposed areas by a chemical developer, making it a positive photoresist. PMMA's advantage is that it allows for extremely high resolution patterns to be made. Smooth PMMA surface can be easily nanostructured by treatment in oxygenradio-frequency plasma[50]and nanostructured PMMA surface can be easily smoothed byvacuum ultraviolet(VUV) irradiation.[50]
  • PMMA is used as a shield to stop beta radiation emitted from radioisotopes.
  • Small strips of PMMA are used asdosimeterdevices during theGammaIrradiation process. The optical properties of PMMA change as the gamma dose increases, and can be measured with aspectrophotometer.
  • Blacklight-reactiveUV tattoosmay usetattoo inkmade with PMMAmicrocapsulesandfluorescentdyes.[51]
  • In the 1960s,luthierDan Armstrongdeveloped a line of electric guitars and basses whose bodies were made completely of acrylic. These instruments were marketed under theAmpegbrand.Ibanez[52]andB.C. Richhave also made acrylic guitars.
  • Ludwig-Mussermakes a line of acrylic drums called Vistalites, well known as being used byLed ZeppelindrummerJohn Bonham.
  • Artificial nailsin the "acrylic" type often include PMMA powder.[53]
  • Some modern briar, and occasionally meerschaum, tobacco pipes sport stems made of Lucite.
  • PMMA technology is utilized in roofing and waterproofing applications. By incorporating a polyester fleece sandwiched between two layers of catalyst-activated PMMA resin, a fully reinforced liquid membrane is createdin situ.
  • PMMA is a widely used material to createdeal toysandfinancial tombstones.
  • PMMA is used by the Sailor Pen Company ofKure, Japan,in their standard models of gold-nibfountain pens,specifically as the cap and body material.

See also

[edit]

References

[edit]
  1. ^abcPolymethylmethacrylate (PMMA, Acrylic)Archived2015-04-02 at theWayback Machine.Makeitfrom.com. Retrieved 2015-03-23.
  2. ^Wapler, M. C.; Leupold, J.; Dragonu, I.; von Elverfeldt, D.; Zaitsev, M.; Wallrabe, U. (2014). "Magnetic properties of materials for MR engineering, micro-MR and beyond".JMR.242(2014): 233–242.arXiv:1403.4760.Bibcode:2014JMagR.242..233W.doi:10.1016/j.jmr.2014.02.005.PMID24705364.S2CID11545416.
  3. ^abRefractive index and related constants – Poly(methyl methacrylate) (PMMA, Acrylic glass)Archived2014-11-06 at theWayback Machine.Refractiveindex.info. Retrieved 2014-10-27.
  4. ^Plexiglas history by Evonik(in German).
  5. ^"DPMAregister | Marken - Registerauskunft".register.dpma.de.Retrieved2021-09-29.
  6. ^Congressional Record: Proceedings and Debates of the 77th Congress First Session(Volume 87, Part 11 ed.). Washington, D.C.: U.S. Government Printing Office. 1941. pp. A2300–A2302.Retrieved3 August2020.
  7. ^"Polymethyl methacrylate | chemical compound".Archivedfrom the original on 2017-10-31.Retrieved2017-05-22.
  8. ^"polymethyl methacrylate",Dorland's Illustrated Medical Dictionary,Elsevier
  9. ^"polymethyl methacrylate".Merriam-Webster.com Dictionary.
  10. ^David K. Platt (1 January 2003).Engineering and High Performance Plastics Market Report: A Rapra Market Report.Smithers Rapra. p. 170.ISBN978-1-85957-380-8.Archivedfrom the original on 21 April 2016.
  11. ^abcdCharles A. Harper; Edward M. Petrie (10 October 2003).Plastics Materials and Processes: A Concise Encyclopedia.John Wiley & Sons. p. 9.ISBN978-0-471-45920-0.Archivedfrom the original on 20 April 2016.
  12. ^"Trademark Electronic Search System".TESS.US Patent and Trademark Office. p. Search for Registration Number 0350093.Retrieved29 June2014.
  13. ^"Misused materials stoked Sumerland fire".New Scientist.62(902). IPC Magazines: 684. 13 June 1974.ISSN0262-4079.Archivedfrom the original on 21 April 2016.
  14. ^"WIPO Global Brand Database".Archivedfrom the original on 2013-01-21.Retrieved2013-01-25.
  15. ^"Never cut these materials"(PDF).[failed verification]
  16. ^abDATA TABLE FOR: Polymers: Commodity Polymers: PMMAArchived2007-12-13 at theWayback Machine.Matbase.com. Retrieved 2012-05-09.
  17. ^Zeng, W. R.; Li, S. F.; Chow, W. K. (2002). "Preliminary Studies on Burning Behavior of Polymethylmethacrylate (PMMA)".Journal of Fire Sciences.20(4): 297–317.doi:10.1177/073490402762574749.hdl:10397/31946.S2CID97589855.INIST14365060.
  18. ^McKeen, Laurence W. (2019).The effect of UV light and weather on plastics and elastomers(4th ed.). Washington, WA: Elsevier. p. 254.ISBN978-0-1281-6457-0.
  19. ^Altuglas International Plexiglas UF-3 UF-4 and UF-5 sheetsArchived2006-11-17 at theWayback Machine.Plexiglas.com. Retrieved 2012-05-09.
  20. ^Myer EzrinPlastics Failure Guide: Cause and PreventionArchived2016-04-21 at theWayback Machine,Hanser Verlag, 1996ISBN1-56990-184-8,p. 168
  21. ^Ishiyama, Chiemi; Yamamoto, Yoshito; Higo, Yakichi (2005). Buchheit, T.; Minor, A.; Spolenak, R.; et al. (eds.). "Effects of Humidity History on the Tensile Deformation Behaviour of Poly(methyl–methacrylate) (PMMA) Films".MRS Proceedings.875:O12.7.doi:10.1557/PROC-875-O12.7.
  22. ^"Tangram Technology Ltd. – Polymer Data File – PMMA".Archivedfrom the original on 2010-04-21.
  23. ^Cappitelli, Francesca; Principi, Pamela; Sorlini, Claudia (2006). "Biodeterioration of modern materials in contemporary collections: Can biotechnology help?".Trends in Biotechnology.24(8): 350–4.doi:10.1016/j.tibtech.2006.06.001.PMID16782219.
  24. ^Rinaldi, Andrea (2006)."Saving a fragile legacy. Biotechnology and microbiology are increasingly used to preserve and restore the world's cultural heritage".EMBO Reports.7(11): 1075–9.doi:10.1038/sj.embor.7400844.PMC1679785.PMID17077862.
  25. ^"Working with Plexiglas"Archived2015-02-21 at theWayback Machine.science-projects.com.
  26. ^Andersen, Hans J."Tensions in acrylics when laser cutting".Archivedfrom the original on 8 December 2015.Retrieved23 December2014.
  27. ^López, Alejandro; Hoess, Andreas; Thersleff, Thomas; Ott, Marjam; Engqvist, Håkan; Persson, Cecilia (2011-01-01)."Low-modulus PMMA bone cement modified with castor oil".Bio-Medical Materials and Engineering.21(5–6): 323–332.doi:10.3233/BME-2012-0679.ISSN0959-2989.PMID22561251.
  28. ^abStickler, Manfred; Rhein, Thoma (2000). "Polymethacrylates".Ullmann's Encyclopedia of Industrial Chemistry.doi:10.1002/14356007.a21_473.ISBN3527306730.
  29. ^Ashby, Michael F.(2005).Materials Selection in Mechanical Design(3rd ed.). Elsevier. p.519.ISBN978-0-7506-6168-3.
  30. ^Kutz, Myer (2002).Handbook of Materials Selection.John Wiley & Sons. p.341.ISBN978-0-471-35924-1.
  31. ^Terry Pepper, Seeing the Light, IlluminationArchived2009-01-23 at theWayback Machine.Terrypepper.com. Retrieved 2012-05-09.
  32. ^Deplazes, Andrea, ed. (2013).Constructing Architecture – Materials Processes Structures, A Handbook.Birkhäuser.ISBN978-3038214526.
  33. ^Yeang, Ken.Light Pipes: An Innovative Design Device for Bringing Natural Daylight and Illumination into Buildings with Deep Floor PlanArchived2009-03-05 at theWayback Machine,Nomination for the Far East Economic Review Asian Innovation Awards 2003
  34. ^"Lighting up your workplace".Fresh Innovators.May 9, 2005. Archived fromthe originalon 2 July 2005.
  35. ^Kenneth YeangArchived2008-09-25 at theWayback Machine,World Cities Summit 2008, June 23–25, 2008, Singapore
  36. ^Gerchikov, Victor; Mossman, Michele; Whitehead, Lorne (2005). "Modeling Attenuation versus Length in Practical Light Guides".LEUKOS.1(4): 47–59.doi:10.1582/LEUKOS.01.04.003.S2CID220306943.
  37. ^How Serraglaze worksArchived2009-03-05 at theWayback Machine.Bendinglight.co.uk. Retrieved 2012-05-09.
  38. ^Glaze of lightArchived2009-01-10 at theWayback Machine,Building Design Online, June 8, 2007
  39. ^Robert A. Meyers, "Molecular biology and biotechnology: a comprehensive desk reference", Wiley-VCH, 1995, p. 722ISBN1-56081-925-1
  40. ^Apple, David J (2006).Sir Harold Ridely and His Fight for Sight: He Changed the World So That We May Better See It.Thorofare NJ USA: Slack.ISBN978-1-55642-786-2.
  41. ^Carroll, Gregory T.; Kirschman, David L. (2022-07-13)."A portable negative pressure unit reduces bone cement fumes in a simulated operating room".Scientific Reports.12(1): 11890.Bibcode:2022NatSR..1211890C.doi:10.1038/s41598-022-16227-x.ISSN2045-2322.PMC9279392.PMID35831355.
  42. ^Kaufmann, Timothy J.; Jensen, Mary E.; Ford, Gabriele; Gill, Lena L.; Marx, William F.; Kallmes, David F. (2002-04-01)."Cardiovascular Effects of Polymethylmethacrylate Use in Percutaneous Vertebroplasty".American Journal of Neuroradiology.23(4): 601–4.PMC7975098.PMID11950651.
  43. ^"Filling in Wrinkles Safely".U.S. Food and Drug Administration. February 28, 2015.Archivedfrom the original on 21 November 2015.Retrieved8 December2015.
  44. ^Zarb, George Albert (2013).Prosthodontic treatment for edentulous patients: complete dentures and implant-supported prostheses(13th ed.). St. Louis, Mo.: Elsevier Mosby.ISBN9780323078443.OCLC773020864.
  45. ^de Swart, Ursula. My Life with Jan. Collection of Jock de Swart, Durango, CO
  46. ^Syurik, Julia; Jacucci, Gianni; Onelli, Olimpia D.; Holscher, Hendrik; Vignolini, Silvia (22 February 2018)."Bio-inspired Highly Scattering Networks via Polymer Phase Separation".Advanced Functional Materials.28(24): 1706901.doi:10.1002/adfm.201706901.
  47. ^Goodman, Robert L. (2002-11-19).How Electronic Things Work... And What to do When They Don't.McGraw Hill Professional.ISBN9780071429245.PMMA Laserdisc.
  48. ^Williams, K.S.; Mcdonnell, T. (2012),"Recycling liquid crystal displays",Waste Electrical and Electronic Equipment (WEEE) Handbook,Elsevier, pp. 312–338,doi:10.1533/9780857096333.3.312,ISBN978-0-85709-089-8,retrieved2022-06-27
  49. ^Duarte, F. J.(Ed.),Tunable Laser Applications(CRC, New York, 2009) Chapters 3 and 4.
  50. ^abLapshin, R. V.; Alekhin, A. P.; Kirilenko, A. G.; Odintsov, S. L.; Krotkov, V. A. (2010). "Vacuum ultraviolet smoothing of nanometer-scale asperities of poly(methyl methacrylate) surface".Journal of Surface Investigation. X-ray, Synchrotron and Neutron Techniques.4(1): 1–11.doi:10.1134/S1027451010010015.S2CID97385151.
  51. ^Bedocs, Paul M.; Cliffel, Maureen; Mahon, Michael J.; Pui, John (March 2008)."Invisible tattoo granuloma".Cutis.81(3): 262–264.ISSN0011-4162.PMID18441850.
  52. ^JS2K-PLTArchived2007-09-28 at theWayback Machine.Ibanezregister.com. Retrieved 2012-05-09.
  53. ^Symington, Jan (2006). "Salon management".Australian nail technology.Croydon, Victoria, Australia: Tertiary Press. p. 11.ISBN978-0864585981.
[edit]
Retrieved from "https://en.wikipedia.org/w/index.php?title=Poly(methyl_methacrylate)&oldid=1231221008"