Jump to content

Software-defined radio

From Wikipedia, the free encyclopedia
(Redirected fromSoftware Defined Radio)
Multiplexing
Analog modulation
Related topics
Passbandmodulation
Analog modulation
Digital modulation
Hierarchical modulation
Spread spectrum
See also

Software-defined radio(SDR) is aradiocommunication system where components that conventionally have been implemented inanaloghardware (e.g.mixers,filters,amplifiers,modulators/demodulators,detectors,etc.) are instead implemented by means of software on a computer orembedded system.[1]While the concept of SDR is not new, the rapidly evolving capabilities of digital electronics render practical many processes which were once only theoretically possible.

A basic SDR system may consist of acomputerequipped with asound card,or otheranalog-to-digital converter,preceded by some form ofRF front end.Significant amounts ofsignal processingare handed over to the general-purpose processor, rather than being done in special-purpose hardware (electronic circuits). Such a design produces a radio which can receive and transmit widely different radio protocols (sometimes referred to as waveforms) based solely on the software used.

Software radios have significant utility for the military andcell phoneservices, both of which must serve a wide variety of changing radio protocols in real time. In the long term, software-defined radios are expected by proponents like theWireless Innovation Forumto become the dominant technology in radio communications. SDRs, along withsoftware defined antennasare the enablers ofcognitive radio.[2]

Operating principles[edit]

Software defined radio concept

Superheterodyne receiversuse a VFO (variable-frequency oscillator),mixer,andfilterto tune the desired signal to a common IF (intermediate frequency) orbaseband.Typically in SDR, this signal is then sampled by the analog-to-digital converter. However, in some applications it is not necessary to tune the signal to an intermediate frequency and the radio frequency signal is directly sampled by theanalog-to-digital converter(after amplification).

Real analog-to-digital converters lack the dynamic range to pick up sub-microvolt, nanowatt-power radio signals produced by an antenna. Therefore, alow-noise amplifiermust precede the conversion step and this device introduces its own problems. For example, ifspurious signalsare present (which is typical), these compete with the desired signals within the amplifier'sdynamic range.They may introduce distortion in the desired signals, or may block them completely. The standard solution is to putband-pass filtersbetween the antenna and the amplifier, but these reduce the radio's flexibility. Real software radios often have two or three analog channel filters with different bandwidths that are switched in and out.

The flexibility of SDR allows for dynamic spectrum usage, alleviating the need to statically assign the scarce spectral resources to a single fixed service.[3]

History[edit]

In 1970, a researcher[who?]at aUnited States Department of Defenselaboratory coined the term "digital receiver". A laboratory called the Gold Room atTRWin California created a software baseband analysis tool called Midas, which had its operation defined in software.[citation needed]

In 1982, while working under a US Department of Defense contract atRCA,Ulrich L. Rohde's department developed the first SDR, which used theCOSMAC(Complementary Symmetry Monolithic Array Computer) chip. Rohde was the first to present on this topic with his February 1984 talk, "Digital HF Radio: A Sampling of Techniques" at the Third International Conference on HF Communication Systems and Techniques in London.[4]

In 1984, a team at theGarland, Texas,Division ofE-SystemsInc. (nowRaytheon) coined the term "software radio" to refer to a digital baseband receiver, as published in their E-Team company newsletter. A 'Software Radio Proof-of-Concept' laboratory was developed by the E-Systems team that popularized Software Radio within various government agencies. This 1984 Software Radio was a digitalbasebandreceiver that provided programmable interference cancellation and demodulation for broadband signals, typically with thousands ofadaptive filtertaps, using multiplearray processorsaccessing shared memory.[5]

In 1991, Joe Mitola independently reinvented the term software radio for a plan to build aGSMbase station that would combine Ferdensi's digital receiver with E-Systems Melpar's digitally controlled communications jammers for a true software-based transceiver. E-Systems Melpar sold the software radio idea to the US Air Force. Melpar built a prototype commanders' tactical terminal in 1990–1991 that employedTexas InstrumentsTMS320C30processors andHarris Corporationdigital receiver chip sets with digitally synthesized transmission. The Melpar prototype didn't last long because when E-Systems ECI Division manufactured the first limited production units, they decided to "throw out those useless C30 boards", replacing them with conventional RF filtering on transmit and receive and reverting to a digital baseband radio instead of the SpeakEasy like IF ADC/DACs of Mitola's prototype. The Air Force would not let Mitola publish the technical details of that prototype, nor would they let Diane Wasserman publish related software life cycle lessons learned because they regarded it as a "USAF competitive advantage".[citation needed]So instead, with USAF permission, in 1991, Mitola described the architecture principles without implementation details in a paper, "Software Radio: Survey, Critical Analysis and Future Directions" which became the firstIEEEpublication to employ the term in 1992.[6]When Mitola presented the paper at the conference, Bob Prill ofGEC Marconibegan his presentation following Mitola with: "Joe is absolutely right about the theory of a software radio and we are building one."[citation needed]Prill gave a GEC Marconi paper on PAVE PILLAR, a SpeakEasy precursor. SpeakEasy, the military software radio was formulated by Wayne Bonser, then ofRome Air Development Center(RADC), now Rome Labs; by Alan Margulies ofMITRERome, NY; and then Lt Beth Kaspar, the original DARPA SpeakEasy project manager and by others at Rome including Don Upmal. Although Mitola's IEEE publications resulted in the largest global footprint for software radio, Mitola privately credits that DoD lab of the 1970s with its leaders Carl, Dave, and John with inventing the digital receiver technology on which he based software radio once it was possible to transmit via software.[citation needed]

A few months after the National Telesystems Conference 1992, in an E-Systems corporate program review, a vice-president of E-Systems Garland Division objected to Melpar's (Mitola's) use of the term "software radio" without credit to Garland. Alan Jackson, Melpar VP of marketing at that time, asked the Garland VP if their laboratory or devices included transmitters. The Garland VP said: "No, of course not — ours is a software radio receiver." Al replied: "Then it's a digital receiver but without a transmitter, it's not a software radio." Corporate leadership agreed with Al, so the publication stood. Many amateur radio operators and HF radio engineers had realized the value of digitizing HF at RF and of processing it with Texas Instruments TI C30digital signal processors(DSPs) and their precursors during the 1980s and early 1990s. Radio engineers atRoke Manorin the UK and at an organization in Germany had recognized the benefits of ADC at the RF in parallel. Mitola's publication of software radio in the IEEE opened the concept to the broad community of radio engineers. His May 1995 special issue of theIEEE Communications Magazinewith the cover "Software Radio" was regarded as a watershed event with thousands of academic citations. Mitola was introduced by Joao da Silva in 1997 at the First International Conference on Software Radio as "godfather" of software radio in no small part for his willingness to share such a valuable technology "in the public interest".[citation needed]

Perhaps the first software-based radiotransceiverwas designed and implemented by Peter Hoeher and Helmuth Lang at the German Aerospace Research Establishment (DLR,formerlyDFVLR) inOberpfaffenhofen,Germany, in 1988.[7]Both transmitter and receiver of an adaptive digital satellite modem were implemented according to the principles of a software radio, and a flexible hardware periphery was proposed.[citation needed]

In 1995, Stephen Blust coined the term "software defined radio", publishing a request for information from Bell South Wireless at the first meeting of the Modular Multifunction Information Transfer Systems (MMITS) forum in 1996, organized by the USAF and DARPA around the commercialization of their SpeakEasy II program. Mitola objected to Blust's term, but finally accepted it as a pragmatic pathway towards the ideal software radio. Although the concept was first implemented with an IF ADC in the early 1990s, software-defined radios have their origins in the U.S. and European defense sectors of the late 1970s (for example, Walter Tuttlebee described aVLF radiothat used an ADC and an8085 microprocessor),[8]about a year after the First International Conference in Brussels. One of the first public software radio initiatives was the U.S. DARPA-Air Forcemilitaryproject namedSpeakEasy.The primary goal of the SpeakEasy project was to use programmable processing to emulate more than 10 existing military radios, operating infrequencybandsbetween 2 and 2000MHz.[9]Another SpeakEasy design goal was to be able to easily incorporate newcodingand modulation standards in the future, so that military communications can keep pace with advances in coding and modulation techniques.[citation needed]

In 1997,Blaupunktintroduced the term "DigiCeiver" for their new range of DSP-based tuners withSharxincar radiossuch as the Modena & Lausanne RD 148.

SpeakEasy phase I[edit]

From 1990 to 1995, the goal of theSpeakEasyprogram was to demonstrate a radio for theU.S. Air Forcetactical ground air control party that could operate from 2MHzto 2GHz,and thus could interoperate with ground force radios (frequency-agileVHF,FM,andSINCGARS), Air Force radios (VHFAM), Naval Radios (VHFAMandHFSSBteleprinters) andsatellites(microwaveQAM). Some particular goals were to provide a new signal format in two weeks from a standing start, and demonstrate a radio into which multiple contractors could plug parts and software.[citation needed]

The project was demonstrated atTF-XXI Advanced Warfighting Exercise,and demonstrated all of these goals in a non-production radio. There was some discontent with failure of these early software radios to adequately filter out of band emissions, to employ more than the simplest of interoperable modes of the existing radios, and to lose connectivity or crash unexpectedly. Itscryptographicprocessor could not change context fast enough to keep several radio conversations on the air at once. Its software architecture, though practical enough, bore no resemblance to any other. The SpeakEasy architecture was refined at the MMITS Forum between 1996 and 1999 and inspired the DoD integrated process team (IPT) for programmable modular communications systems (PMCS) to proceed with what became the Joint Tactical Radio System (JTRS).[citation needed]

The basic arrangement of the radioreceiverused anantennafeeding anamplifierand down-converter (seeFrequency mixer) feeding anautomatic gain control,which fed ananalog-to-digital converterthat was on a computerVMEbuswith a lot ofdigital signal processors(Texas InstrumentsC40s). The transmitter haddigital-to-analog converterson thePCI busfeeding an up converter (mixer) that led to a power amplifier and antenna. The very wide frequency range was divided into a few sub-bands with different analog radio technologies feeding the same analog to digital converters. This has since become a standard design scheme for wideband software radios.[citation needed]

SpeakEasy phase II[edit]

The goal was to get a more quickly reconfigurable architecture,i.e.,several conversations at once, in anopensoftware architecture, with cross-channel connectivity (the radio can "bridge" different radio protocols). The secondary goals were to make it smaller, cheaper, and weigh less.[citation needed]

The project produced a demonstration radio only fifteen months into a three-year research project. This demonstration was so successful that further development was halted, and the radio went into production with only a 4 MHz to 400 MHz range.[citation needed]

The software architecture identified standard interfaces for different modules of the radio: "radio frequency control" to manage the analog parts of the radio, "modem control" managed resources formodulationanddemodulationschemes (FM, AM, SSB, QAM, etc.), "waveform processing" modules actually performed themodemfunctions, "key processing" and "cryptographic processing" managed the cryptographic functions, a "multimedia" module did voice processing, a "human interface" provided local or remote controls, there was a "routing" module for network services, and a "control" module to keep it all straight.[citation needed]

The modules are said to communicate without a central operating system. Instead, they send messages over thePCIcomputer busto each other with a layered protocol.[citation needed]

As a military project, the radio strongly distinguished "red" (unsecured secret data) and "black" (cryptographically-secured data).[citation needed]

The project was the first known to useFPGAs(field programmable gate arrays) for digital processing of radio data. The time to reprogram these was an issue limiting application of the radio. Today, the time to write a program for an FPGA is still significant, but the time to download a stored FPGA program is around 20 milliseconds. This means an SDR could change transmission protocols and frequencies in one fiftieth of a second, probably not an intolerable interruption for that task.[citation needed]

2000s[edit]

The SpeakEasy SDR system in the 1994 uses aTexas Instruments TMS320C30CMOSdigital signal processor(DSP), along with several hundredintegrated circuitchips, with the radio filling the back of a truck. By the late 2000s, the emergence ofRF CMOStechnology made it practical to scale down an entire SDR system onto a singlemixed-signalsystem-on-a-chip,whichBroadcomdemonstrated with the BCM21551 processor in 2007. The Broadcom BCM21551 has practical commercial applications, for use in3Gmobile phones.[10][11]

Military usage[edit]

United States[edit]

TheJoint Tactical Radio System(JTRS) was a program of the US military to produce radios that provide flexible and interoperable communications. Examples of radio terminals that require support include hand-held, vehicular, airborne and dismounted radios, as well as base-stations (fixed and maritime).

This goal is achieved through the use of SDR systems based on an internationally endorsed openSoftware Communications Architecture(SCA). This standard usesCORBAonPOSIXoperating systems to coordinate various software modules.

The program is providing a flexible new approach to meet diverse soldier communications needs through software programmable radio technology. All functionality and expandability is built upon the SCA.

The SCA, despite its military origin, is under evaluation by commercial radio vendors for applicability in their domains. The adoption of general-purpose SDR frameworks outside of military, intelligence, experimental and amateur uses, however, is inherently hampered by the fact that civilian users can more easily settle with a fixed architecture, optimized for a specific function, and as such more economical in mass market applications. Still, software defined radio's inherent flexibility can yield substantial benefits in the longer run, once the fixed costs of implementing it have gone down enough to overtake the cost of iterated redesign of purpose built systems. This then explains the increasing commercial interest in the technology.

SCA-based infrastructure software and rapid development tools for SDR education and research are provided by the Open Source SCA Implementation – Embedded (OSSIE[12]) project. The Wireless Innovation Forum funded the SCA Reference Implementation project, an open source implementation of the SCA specification. (SCARI) can be downloaded for free.

Amateur and home use[edit]

Microtelecom Perseus – an HF SDR for the amateur radio market

A typicalamateursoftware radio uses adirect conversion receiver.Unlike direct conversion receivers of the more distant past, the mixer technologies used are based on the quadrature sampling detector and the quadrature sampling exciter.[13][14][15][16]

The receiver performance of this line of SDRs is directly related to the dynamic range of the analog-to-digital converters (ADCs) utilized.[17]Radio frequency signals are down converted to the audio frequency band, which is sampled by a high performance audio frequency ADC. First generation SDRs used a 44 kHz PC sound card to provideADCfunctionality. The newer software defined radios use embedded high performance ADCs that provide higherdynamic rangeand are more resistant to noise and RF interference.

A fast PC performs thedigital signal processing(DSP) operations using software specific for the radio hardware. Several software radio implementations use the open source SDR library DttSP.[18]

The SDR software performs all of the demodulation, filtering (both radio frequency and audio frequency), and signal enhancement (equalization and binaural presentation). Uses include every common amateur modulation:morse code,single-sideband modulation,frequency modulation,amplitude modulation,and a variety of digital modes such asradioteletype,slow-scan television,andpacket radio.[19]Amateurs also experiment with new modulation methods: for instance, theDREAMopen-sourceproject decodes theCOFDMtechnique used byDigital Radio Mondiale.

There is a broad range of hardware solutions for radio amateurs and home use. There are professional-grade transceiver solutions, e.g. the Zeus ZS-1[20][21]or FlexRadio,[22]home-brew solutions, e.g. PicAStar transceiver, the SoftRock SDR kit,[23]and starter or professional receiver solutions, e.g. the FiFi SDR[24]for shortwave, or the Quadrus coherent multi-channel SDR receiver[25]for short wave or VHF/UHF in direct digital mode of operation.

RTL-SDR[edit]

Internals of a low-costDVB-TUSB dongle that uses Realtek RTL2832U (square IC on the right) as the controller and Rafael Micro R820T (square IC on the left) as the tuner

Eric Fry discovered that some common low-costDVB-TUSB dongles with the Realtek RTL2832U[26][27]controller and tuner, e.g. the Elonics E4000 or the Rafael Micro R820T,[28]can be used as a wide-band (3 MHz) SDR receiver. Experiments proved the capability of this setup to analyzePerseids meteor showerusingGraves radarsignals.[29]This project is being maintained atOsmocom.

HPSDR[edit]

TheHPSDR(High Performance Software Defined Radio) project uses a 16-bit135 MSPSanalog-to-digital converter that provides performance over the range 0 to55 MHzcomparable to that of a conventional analogue HF radio. The receiver will also operate in the VHF and UHF range using either mixer image or alias responses. Interface to a PC is provided by aUSB2.0 interface, althoughEthernetcould be used as well. The project is modular and comprises abackplaneonto which other boards plug in. This allows experimentation with new techniques and devices without the need to replace the entire set of boards. Anexciterprovides1/2 Wof RF over the same range or into the VHF and UHF range using image or alias outputs.[30]

WebSDR[edit]

WebSDR[31]is a project initiated by Pieter-Tjerk de Boer providing access via browser to multiple SDR receivers worldwide covering the complete shortwave spectrum. De Boer has analyzedChirp Transmittersignals using the coupled system of receivers.[32]

KiwiSDR[edit]

KiwiSDR[33]is also a via-browser SDR like WebSDR. Unlike WebSDR, the frequency is limited to 3 Hz to 30 MHz (ELFtoHF)

Other applications[edit]

On account of its increasing accessibility, with lower cost hardware, more software tools and documentation, the applications of SDR have expanded past their primary and historic use cases. SDR is now being used in areas such as wildlife tracking, radio astronomy, medical imaging research, and art.

See also[edit]

References[edit]

  1. ^Markus Dillinger; Kambiz Madani; Nancy Alonistioti (2003).Software Defined Radio: Architectures, Systems and Functions.Wiley & Sons. p. xxxiii.ISBN0-470-85164-3.
  2. ^Amaral, Cristiano (2021).Guia Moderno do Radioescuta.Brazil: Amazon. p. 333.ISBN978-65-00-20800-9.
  3. ^Staple, Gregory; Werbach, Kevin (March 2004)."The End of Spectrum Scarcity".IEEE Spectrum.41(3): 48–52.doi:10.1109/MSPEC.2004.1270548.S2CID1667310.
  4. ^"Ulrich Rohde, N1UL, Recognized for Pioneering Work on SDR".American Radio Relay League.2017-01-17.Retrieved2024-01-10.
  5. ^Johnson, P. (May 1985)."New Research Lab Leads to Unique Radio Receiver"(PDF).E-Systems Team.5(4): 6–7.
  6. ^Mitola III, J. (1992).Software radios-survey, critical evaluation and future directions.National Telesystems Conference. pp. 13/15 to 13/23.doi:10.1109/NTC.1992.267870.ISBN0-7803-0554-X.
  7. ^P. Hoeher and H. Lang, "Coded-8PSK modem for fixed and mobile satellite services based on DSP," in Proc. First Int. Workshop on Digital Signal Processing Techniques Applied to Space Communications, ESA/ ESTEC, Noordwijk, Netherlands, Nov. 1988; ESA WPP-006, Jan. 1990, pp. 117-123.
  8. ^First International Workshop on Software Radio, Greece 1998
  9. ^RJ Lackey and DW Upmal contributed the article "Speakeasy: The Military Software Radio" to the IEEE Communications Magazine special issue that Mitola edited and for which Mitola wrote the lead article "Software Radio Architecture", in May 1995.
  10. ^Leenaerts, Domine (May 2010).Wide band RF CMOS circuit design techniques(PDF).IEEE Solid-State Circuits SocietyDistinguished Lecturers Program (SSCS DLP).NXP Semiconductors.Retrieved10 December2019.
  11. ^"Broadcom ships" 3G phone on a chip "".The LinuxDevices Archive.16 October 2007.Retrieved12 December2019.
  12. ^"OSSIE".vt.edu.Archived fromthe originalon 2009-03-12.
  13. ^Youngblood, Gerald (July 2002),"A Software Defined Radio for the Masses, Part 1"(PDF),QEX,American Radio Relay League:1–9
  14. ^Youngblood, Gerald (Sep–Oct 2002),"A Software Defined Radio for the Masses, Part 2"(PDF),QEX,American Radio Relay League:10–18
  15. ^Youngblood, Gerald (Nov–Dec 2002),"A Software Defined Radio for the Masses, Part 3"(PDF),QEX,American Radio Relay League:1–10
  16. ^Youngblood, Gerald (Mar–Apr 2003),"A Software Defined Radio for the Masses, Part 4"(PDF),QEX,American Radio Relay League:20–31
  17. ^Rick Lindquist; Joel R. Hailas (October 2005)."FlexRadio Systems; SDR-1000 HF+VHF Software Defined Radio Redux".QST.Retrieved2008-12-07.
  18. ^DttSP on Source Forge
  19. ^http://sourceforge.net/projects/sdrOpen source SDR transceiver project using USRP and GNU Radio
  20. ^ZS-1 Project
  21. ^ZS-1 Zeus Transceiver
  22. ^Flex Radio SDR Transceivershttp://www.flex-radio.com/
  23. ^SoftRock SDR Kitshttp://wb5rvz.com/sdr/
  24. ^FiFi SDR Receiverhttp://o28.sischa.net/fifisdr/trac
  25. ^Quadrus coherenet multi-channel SDR receiver
  26. ^Using DVB USB Stick as SDR Receiverhttp://sdr.osmocom.org/trac/wiki/rtl-sdr
  27. ^RTL-SDR Bloghttp://www.rtl-sdr.com
  28. ^Support for the Rafael Micro R820T tuner in Cocoa Radiohttps://housedillon.com/blog/support-for-the-rafael-micro-r820t-tuner-o-cocoa-radio/
  29. ^"Perseids shower using graves radar".EB3FRN.7 October 2013.
  30. ^"HPSDR Web Site".
  31. ^WebSDRhttp://websdr.org
  32. ^Chirp Signals analyzed using SDRhttp://websdr.ewi.utwente.nl:8901/chirps/
  33. ^"KiwiSDR".

Further reading[edit]

  • Rohde, Ulrich L (February 26–28, 1985). "Digital HF Radio: A Sampling of Techniques".Third International Conference on HF Communication Systems and Techniques.London, England.
  • Software defined radio: architectures, systems, and functions.Dillinger, Madani, Alonistioti. Wiley, 2003. 454 pages.ISBN0-470-85164-3ISBN9780470851647
  • Cognitive Radio Technology.Bruce Fette. Elsevier Science & Technology Books, 2006. 656 pags.ISBN0-7506-7952-2ISBN9780750679527
  • Software Defined Radio for 3G,Burns. Artech House, 2002.ISBN1-58053-347-7
  • Software Radio: A Modern Approach to Radio Engineering,Jeffrey H. Reed. Prentice Hall PTR, 2002.ISBN0-13-081158-0
  • Signal Processing Techniques for Software Radio,Behrouz Farhang-Beroujeny. LuLu Press.
  • RF and Baseband Techniques for Software Defined Radio,Peter B. Kenington. Artech House, 2005,ISBN1-58053-793-6
  • The ABC's of Software Defined Radio,Martin Ewing, AA6E. The American Radio Relay League, Inc., 2012,ISBN978-0-87259-632-0
  • Software Defined Radio using MATLAB & Simulink and the RTL-SDR,R Stewart, K Barlee, D Atkinson, L Crockett, Strathclyde Academic Media, September 2015.ISBN978-0-9929787-2-3

External links[edit]

Wikimedia Commons has media related toSoftware defined radios.
Retrieved from "https://en.wikipedia.org/w/index.php?title=Software-defined_radio&oldid=1231474929"