Software flow control

"Xon" redirects here. For the Star Trek character, seeStar Trek: Phase II § Cast.For the oil company which formerly traded as XON, seeExxonMobil.

Software flow controlis a method offlow controlused in computerdata links,especiallyRS-232 serial.It uses special codes, transmittedin-band,over the primary communications channel. These codes are generally calledXOFFandXON(from "transmit off" and "transmit on", respectively). Thus, "software flow control" is sometimes called "XON/XOFF flow control". This is in contrast to flow control via dedicatedout-of-bandsignals — "hardware flow control"— such asRS-232 RTS/CTS.

Representation

For systems using theASCIIcharacter code, XOFF is generally represented using acharacterorbytewith decimal value 19; XON with value 17.

The ASCII standard does not reserve anycontrol charactersfor use as XON/XOFF specifically. However, it does provide four generic "device control" characters (DC1 through DC4). TheTeletype Model 33ASR adopted two of these, DC3 and DC1, for use as XOFF and XON, respectively. This usage was copied by others, and is now ade facto standard.The keyboard equivalents ofCtrl+Sfor XOFF, andCtrl+Qfor XON, also derive from this usage.

XOFF/XON representations in ASCII

Code	Meaning	ASCII	Dec	Hex	Keyboard
XOFF	Pause transmission	DC3	19	13	Ctrl+S
XON	Resume transmission	DC1	17	11	Ctrl+Q

Mechanism

When one end of a data link is unable to accept any more data (or approaching that point), it sends XOFF to the other end. The other end receives the XOFF code, and suspendstransmission.Once the first end is ready to accept data again, it sends XON, and the other end resumes transmission.

For example, one may imagine acomputersending data to a slowprinter.Since the computer is faster at sending data than the printer can print it, the printer falls behind and approaches a situation where it would be overwhelmed by the data. The printer reacts to this situation by sending XOFF to the computer, which temporarily stops sending data. When the printer is again ready to receive more data, it sends XON to the computer, which starts sending data again.

XOFF/XON can be employed in both directions, for example, twoteleprintersconnected to each other.

Comparison with hardware flow control

The principal advantage of software flow control is the reduction in the number ofelectrical conductorsbetween sender and receiver. Given acommon ground,only two signals are needed, one to send and the other to receive. Hardware flow control requires additional wires between the two devices. It also requires specific hardware implementation, which had more significant costs in earlier days of computing (i.e., 1960s and 70s).

However, software flow control is not without its problems. The most important drawback is that software flow control is less reliable. Sending XOFF requires at least one character time to transmit, and may be queued behind already-transmitted data still in buffers. Hardware signals may be asserted almost instantaneously, and out-of-order.

Summary of flow control tradeoffs

Type	Data integrity	Low cost	Out of Band
Hardware flow control	Most reliable	No	Yes
On-chip software f.c.	Good	Some	No
Software f.c. (FIFO disabled)	Good, but slow	Yes	No
Software f.c. (FIFO enabled)	Unreliable	Yes	No

As the name "software flow control" implies, flow control using this method isusuallyimplemented in software (orfirmware), which can cause further delays in XOFF response. These delays can lead to data corruption due tobuffer overruns.Hardware flow control, on the other hand, is typically under the direct control of the transmittingUART,which is able to cease transmission immediately, without the intervention of higher levels. To handle the latency caused by builtinFIFOs,more advanced UARTs, like the 16950, provide "on-chip" software flow control.UARTs that lack such support, like the16550,may suffer from buffer overruns when using software flow control, although this can be somewhat mitigated by disabling the UART's FIFO.

Finally, since the XOFF/XON codes are sent in-band, they cannot appear in the data being transmitted without being mistaken for flow control commands. Any data containing the XOFF/XON codes thus must be encoded in some manner for proper transmission, with corresponding overhead. This is frequently done with some kind ofescape sequence.For printing devices that directly interpret ASCII codes, this is not a large problem, because the XON and XOFF codes useASCII"device control" code numbers.

Applications

Software flow control is used extensively by low-speed devices, especially olderprintersanddumb terminals,to indicate they are temporarily unable to accept more data. Typically, this is due to a combination of limitedoutputrate and anybuffersbeing full. Some terminal control packages, such astermcap,employ "padding" (short delays using millisecond granularity) to allow such equipment sufficient time to perform the requested actions without the need to assert XOFF.

XOFF/XON are still sometimes used manually by computer operators, to pause and restart output which otherwise wouldscrolloff the display too quickly.

Terminal emulatorsoftware generally implements XOFF/XON support as a basic function. This generally includes thesystem consoleon modernUnixandLinuxmachines, as well asGUIemulators such asxtermand theWin32 console.

Robust XON is a technique to restart communication, just in case it was stopped by an accidentally received XOFF. The receiving unit sends periodic XON characters when it can receive data, and the line is idle. One common use is by serial printers (likeHP LaserJetII) to indicate they are online and ready to receive data. The XON is sent every 1 to 30 seconds depending on the printer's firmware design.

See also

• Ethernet flow control

References

• "HP LaserJet IIP and IIP Plus Printers - Control Panel Keys and Menus".Hewlett-Packard.Archived fromthe originalon May 9, 2006.