Intermediate frequency

The IF stage from a Motorola 19K1 television setcirca1949

In communications andelectronic engineering,anintermediate frequency(IF) is afrequencyto which acarrier waveis shifted as an intermediate step intransmissionor reception.The intermediate frequency is created by mi xing the carrier signal with alocal oscillatorsignal in a process calledheterodyning,resulting in a signal at the difference orbeat frequency.Intermediate frequencies are used insuperheterodyne radio receivers,in which an incoming signal is shifted to an IF foramplificationbefore finaldetectionis done.

Conversion to an intermediate frequency is useful for several reasons. When several stages of filters are used, they can all be set to a fixed frequency, which makes them easier to build and to tune. Lower frequency transistors generally have higher gains so fewer stages are required. It's easier to make sharply selective filters at lower fixed frequencies.

There may be several such stages of intermediate frequency in a superheterodyne receiver; two or three stages are calleddouble(alternatively,dual) ortriple conversion,respectively.

Justification

Intermediate frequencies are used for three general reasons.At very high (gigahertz) frequencies, signal processing circuitry performs poorly. Active devices such astransistorscannot deliver much amplification (gain).Ordinary circuits usingcapacitorsandinductorsmust be replaced with cumbersome high frequency techniques such asstriplinesandwaveguides.So a high frequency signal is converted to a lower IF for more convenient processing. For example, insatellite dishes,the microwave downlink signal received by the dish is converted to a much lower IF at the dish so that a relatively inexpensivecoaxial cablecan carry the signal to the receiver inside the building. Bringing the signal in at the original microwave frequency would require an expensivewaveguide.

In receivers that can be tuned to different frequencies, a second reason is to convert the various different frequencies of the stations to a common frequency for processing. It is difficult to build multistageamplifiers,filters,anddetectorsthat can have all stages track the tuning of different frequencies, but it is comparatively easy to build tunableoscillators.Superheterodyne receivers tune in different frequencies by adjusting the frequency of the local oscillator on the input stage, and all processing after that is done at the same fixed frequency: the IF. Without using an IF, all the complicated filters and detectors in a radio or television would have to be tuned in unison each time the frequency was changed as was necessary in the earlytuned radio frequency receivers(TRF). A more important advantage is that it gives the receiver a constant bandwidth over its tuning range. The bandwidth of a filter is proportional to its center frequency. In receivers like the TRF in which the filtering is done at the incoming RF frequency, as the receiver is tuned to higher frequencies, its bandwidth increases.

The main reason for using an intermediate frequency is to improve frequencyselectivity.In communication circuits, a very common task is to separate out, or extract, signals or components of a signal that are close together in frequency. This is calledfiltering.Some examples are: picking up a radio station among several that are close in frequency, or extracting thechrominancesubcarrier from a TV signal. With all known filtering techniques the filter'sbandwidthincreases proportionately with the frequency. So a narrower bandwidth and more selectivity can be achieved by converting the signal to a lower IF and performing the filtering at that frequency.FMandtelevision broadcastingwith their narrow channel widths, as well as more modern telecommunications services such ascell phonesandcable television,would be impossible without using frequency conversion.

Uses

Perhaps the most commonly used intermediate frequencies for broadcast receivers are around 455 kHz for AM receivers and 10.7 MHz for FM receivers. In special purpose receivers other frequencies can be used. A dual-conversion receiver may have two intermediate frequencies, a higher one to improve image rejection and a second, lower one, for desired selectivity. A first intermediate frequency may even be higher than the input signal, so that all undesired responses can be easily filtered out by a fixed-tuned RF stage.

In a digital receiver, theanalog-to-digital converter(ADC) operates at low sampling rates, so input RF must be mixed down to IF to be processed. Intermediate frequency tends to be lower frequency range compared to the transmitted RF frequency. However, the choices for the IF are most dependent on the available components such asmixer,filters, amplifiers and others that can operate at lower frequency. There are other factors involved in deciding the IF, because lower IF is susceptible to noise and higher IF can cause clock jitters.

Modernsatellite televisionreceivers use several intermediate frequencies.The 500 television channels of a typical system are transmitted from the satellite to subscribers in theKumicrowave band, in two subbands of 10.7–11.7 and 11.7–12.75 GHz. The downlink signal is received by asatellite dish.In the box at the focus of the dish, called alow-noise block downconverter(LNB), each block of frequencies is converted to the IF range of 950–2150 MHz by two fixed frequency local oscillators at 9.75 and 10.6 GHz. One of the two blocks is selected by a control signal from the set top box inside, which switches on one of the local oscillators. This IF is carried into the building to the television receiver on a coaxial cable. At the cable company'sset top box,the signal is converted to a lower IF of 480 MHz for filtering, by a variable frequency oscillator.This is sent through a 30 MHz bandpass filter, which selects the signal from one of thetransponderson the satellite, which carries several channels. Further processing selects the channel desired, demodulates it and sends the signal to the television.

History

An intermediate frequency was first used in the superheterodyne radio receiver, invented by American scientist MajorEdwin Armstrongin 1918, duringWorld War I.A member of theSignal Corps,Armstrong was building radiodirection findingequipment to track German military signals at the then-very high frequencies of 500 to 3500 kHz. Thetriode vacuum tubeamplifiers of the day would not amplify stably above 500 kHz; however, it was easy to get them tooscillateabove that frequency. Armstrong's solution was to set up an oscillator tube that would create a frequency near the incoming signal and mix it with the incoming signal in a mixer tube, creating aheterodyneor signal at the lower difference frequency where it could be amplified easily. For example, to pick up a signal at 1500 kHz the local oscillator would be tuned to 1450 kHz. Mi xing the two created an intermediate frequency of 50 kHz, which was well within the capability of the tubes. The namesuperheterodynewas a contraction ofsupersonic heterodyne,to distinguish it from receivers in which the heterodyne frequency was low enough to be directly audible, and which were used for receivingcontinuous wave(CW)Morse codetransmissions (not speech or music).

After the war, in 1920, Armstrong sold the patent for the superheterodyne toWestinghouse,who subsequently sold it toRCA.The increased complexity of the superheterodyne circuit compared to earlierregenerativeortuned radio frequency receiverdesigns slowed its use, but the advantages of the intermediate frequency for selectivity and static rejection eventually won out; by 1930, most radios sold were 'superhets'. During the development ofradarinWorld War II,the superheterodyne principle was essential for downconversion of the very high radar frequencies to intermediate frequencies. Since then, the superheterodyne circuit, with its intermediate frequency, has been used in virtually all radio receivers.

Examples

The RCA Radiola AR-812used 6 triodes: a mixer, local oscillator, two IF and two audio amplifier stages, with an IF of 45 kHz.

• down to c. 20 kHz,30 kHz (A. L. M. Sowerby and H. B. Dent),45 kHz (first commercial superheterodyne receiver: RCA Radiola AR-812 of 1923/1924),c. 50 kHz,c. 100 kHz,c. 120 kHz
• 110 kHz was used in European AMlongwavebroadcast receivers.
• 175 kHz (early wide band and communications receivers before introduction of powdered iron cores)
• 260 kHz (early standard broadcast receivers),250–270 kHz
• Copenhagen Frequency Allocations: 415–490 kHz, 510–525 kHz
• AM radioreceivers: 450 kHz, 455 kHz (most common),460 kHz, 465 kHz,467 kHz, 470 kHz, 475 kHz, and 480 kHz.
• FM radioreceivers: 262 kHz (old car radios),455 kHz, 1.6 MHz, 5.5 MHz, 10.7 MHz (most common),10.8 MHz,11.2 MHz, 11.7 MHz, 11.8 MHz, 13.45 MHz,21.4 MHz, 75 MHz and 98 MHz. In double-conversion superheterodyne receivers, a first intermediate frequency of 10.7 MHz is often used, followed by a second intermediate frequency of 470 kHz (or 700 kHz withDYNAS). There are triple conversion designs used in police scanner receivers, high-end communications receivers, and many point-to-point microwave systems. Modern DSP chip consumer radios often use a 'low-IF' of 128 kHz for FM.
• Narrowband FMreceivers: 455 kHz (most common),470 kHz
• Shortwave receivers: 1.6 MHz,1.6–3.0 MHz,4.3 MHz (for 40–50 MHz-only receivers).In double-conversion superheterodyne receivers, a first intermediate frequency of 3.0 MHz is sometimes combined with a second IF of 465 kHz.
• Analoguetelevision receivers using system M: 41.25 MHz (audio) and 45.75 MHz (video). Note, the channel is flipped over in the conversion process in anintercarriersystem, so the audio IF is lower than the video IF. Also, there is no audio local oscillator; the injected video carrier serves that purpose.
• Analoguetelevision receivers using system B and similar systems: 33.4 MHz for the aural and 38.9 MHz for the visual signal. (The discussion about the frequency conversion is the same as in system M.)
• Satelliteuplink-downlinkequipment: 70 MHz, 950–1450 MHz (L-band) downlink first IF.
• Terrestrialmicrowaveequipment: 250 MHz, 70 MHz or 75 MHz.
• Radar:30 MHz.
• RFtest equipment: 310.7 MHz, 160 MHz, and 21.4 MHz.

See also

• Mechanical filter
• Low-IF receiver
• Zero-IF receiver