Recyclebot
![]() | This articlemay beconfusing or unclearto readers.In particular, the article mixes up the use of "recyclebot" as a generic noun for DIY filament squeezers and RecycleBot the family of GPLv3 machines.(November 2020) |
Arecyclebot(or RecycleBot) is anopen-source hardwaredevice forconverting waste plasticinto filament for open-source3D printerslike theRepRap.[1]MakingDIY3D printer filament at home is both less costly and better for the environment than purchasing conventional 3D printer filament.[2][3][4]In following the RepRap tradition there are recyclebot designs that use mostly 3-D printable parts.[5]
Motivation and benefits
[edit]RepRap 3D printers have been shown to reduce costs for consumers by offsetting purchases that can be printed.[6][7][8][9]The RepRap's plastic feedstock is one area where cost can still be reduced. In 2014, professorJoshua Pearcepointed out that "Filament is retailing for between $36 and $50 a kilogram and you can produce your own filament for 10 cents a kilogram if you use recycled plastic"[10]The device can thus further enhance RepRap affordability by reducing operating costs.[11]In addition, by reducingprosumers'reliance on purchased products, the RepRap and the recyclebot have made it feasible for 3D printing to be used for small-scale manufacturing to aidsustainable development.[12][13]It has been postulated that recycled filament production could also offer an alternative income source by theEthical Filament Foundation[14][15]or as a form of "fair tradefilament ".[16]It has also been shown to improve theenergy payback timeof even knowngreen energytechnologies likesolar photovoltaics.[17]
Technology
[edit]The RecycleBot is anopen-source hardwareproject – thus its plans are freely available on the Internet.
- RecycleBot curated by academics in Canada and the U.S. on Appropedia (here) and at the RepRap Wiki (here). For example, the full parts list (orbill of materials) for the metal and electronic components and the controls are available onThingiverse.[18][19]
- Lyman filament extruder– a DIY recyclebot
History
[edit]The history of the RecycleBot was largely derived from the work on the RepRap Wiki underGNU Free Documentation License1.2.[20]
The first recyclebot was developed by students at Victoria University of Wellington, New Zealand.[21][22][23]This design was a proof of concept and was hand-powered, and so had a smallecological footprint,but did not create filament of high enough quality to be useful for3D printers.The design for thewaste plastic extruder(Recyclebot v2.0 and v2.1) developed atQueen's UniversityCanada andMichigan Techwas heavily influenced by the Web4Deb extruder, which extrudesHDPEfor use as a growth medium in aquaponics.[24]This design for the recyclebot was developed, tested and published in the peer-reviewedrapid prototypingliterature.[25]This device proved viable for producing3D printing filament.TheRecyclebot v2.2is being developed by the Michigan Tech in Open Sustainability Technology Research Group.[26]
ManymakersorDIYenthusiasts have made various versions of RecycleBots. The most notable is theLyman filament extruder.Lyman, a retired engineer, won a design contest to make a low-cost 3D filament fabrication system.[27]As of 2014, there were many types of recyclebots, many of which are at the early stages of commercialization. Recyclebot technology has been applied tohangprintersto allow for fused particle fabrication of large prints without first having to form filament.[28]
Futurist speculation
[edit]Jeremy Rifkinhas hypothesized that such recycling with recyclebots and distributed production with 3D printing will lead to a zero marginal cost society.[29] The science-fiction author,Bruce Sterlingwondered inWiredif recyclebots and 3D printers might be used to turn waste into guns.[30]Recyclebots can provide a new method of recycling.[31]
References
[edit]- ^Baechler, Christian; DeVuono, Matthew; Pearce, Joshua M. (2013)."Distributed Recycling of Waste Polymer into RepRap Feedstock".Rapid Prototyping Journal.19(2): 118–125.doi:10.1108/13552541311302978.S2CID15980607.
- ^Kreiger, M.A.; Mulder, M.L.; Glover, A.G.; Pearce, J. M. (2014)."Life Cycle Analysis of Distributed Recycling of Post-consumer High Density Polyethylene for 3-D Printing Filament".Journal of Cleaner Production.70:90–96.Bibcode:2014JCPro..70...90K.doi:10.1016/j.jclepro.2014.02.009.
- ^The importance of the Lyman Extruder, Filamaker, Recyclebot and Filabot to 3D printingArchived18 March 2014 at theWayback Machine– VoxelFab, 2013.
- ^Kreiger, M.; Anzalone, G. C.; Mulder, M. L.; Glover, A.; Pearce, J. M (2013)."Distributed Recycling of Post-Consumer Plastic Waste in Rural Areas".MRS Proceedings.1492:91–96.doi:10.1557/opl.2013.258.S2CID18303920.
- ^Woern, Aubrey L.; et al. (October 2018)."RepRapable Recyclebot: Open source 3-D printable extruder for converting plastic to 3-D printing filament".HardwareX.4:e00026.doi:10.1016/j.ohx.2018.e00026.ISSN2468-0672.
- ^B.T. Wittbrodt, A.G. Glover, J. Laureto, G.C. Anzalone, D. Oppliger, J.L. Irwin, J.M. Pearce (2013), Life-cycle economic analysis of distributed manufacturing with open-source 3-D printers,Mechatronics,23 (2013), pp. 713–726.open access
- ^Study: At-home 3-D printing could save consumers 'thousands'– CNN, 2013
- ^Printing Keychains and Shower Heads: 3-D Printing Goes Beyond the Lab– ABC News
- ^A 3-D Printer Can Pay For Itself In Less Than A Year– Popular Science, 2013
- ^Turning old plastic into 3D printer filament is greener than conventional recycling– 3Ders, 2014
- ^Study: At-home 3-D printing could save consumers 'thousands'– CNN, 2013
- ^3-D Printing of Open Source Appropriate Technologies for Self-Directed Sustainable Development
- ^DJ Pangburn. 2014.How 3D Printers Are Boosting Off-The-Grid, Underdeveloped Communities- MotherBoard
- ^http://techfortrade.org/our-initiatives/3d4d-challenge/the-ethical-filament-foundation/Tech for Trade – Ethical Filament Foundation
- ^Charity Targets 3D Printing’s Plastic Waste Problem With Standards For An Ethical Alternative 7 November 2013 by Natasha Lomas, Tech Crunch,https://techcrunch /2013/11/07/ethical-additive-manufacturing/
- ^Feeley, S. R.; Wijnen, B.; Pearce, J. M. (2014)."Evaluation of Potential Fair Trade Standards for an Ethical 3-D Printing Filament".Journal of Sustainable Development.7(5): 1–12.doi:10.5539/jsd.v7n5p1.
- ^Shan Zhong, S. et al.Energy Payback Time of a Solar Photovoltaic Powered Waste Plastic Recyclebot System.Recycling2017, 2(2), 10; doi: 10.3390/recycling2020010
- ^"RecycleBot v2.2 by jpearce".
- ^"RecycleBot v2.3 Controls by jpearce".
- ^"Recyclebot - RepRap".
- ^Burgess, Phil (5 August 2010)."Recyclebot digests milk jugs to feed MakerBot".hackaday /.hackaday.
- ^Duann (3 August 2010)."RecycleBot: Greening the MakerBot".The Shapeways Blog.shapeways.
- ^Pettis, Bre (3 August 2010)."Recyclebot makes HDPE for your MakerBot from Milk Jugs!".makerbot blog.makerbot.
- ^Web4Deb's blog.
- ^Baechler, Christian; DeVuono, Matthew; Pearce, Joshua M. (2013)."Distributed Recycling of Waste Polymer into RepRap Feedstock".Rapid Prototyping Journal.19(2): 118–125.doi:10.1108/13552541311302978.S2CID15980607.
- ^"Category:MOST - Appropedia: The sustainability wiki".
- ^Harry McCracken (4 March 2013)."How an 83-Year-Old Inventor Beat the High Cost of 3D Printing".Time.
- ^Rattan, Ravneet S.; Nauta, Nathan; Romani, Alessia; Pearce, Joshua M. (1 March 2023)."Hangprinter for large scale additive manufacturing using fused particle fabrication with recycled plastic and continuous feeding".HardwareX.13:e00401.doi:10.1016/j.ohx.2023.e00401.ISSN2468-0672.PMC9930197.PMID36818952.
- ^Jeremy Rifkin, Zero Marginal Cost Society, Palgrave Macmillan, 2014.
- ^3D Printed gun moving from sinister joke to sinister business model By Bruce Sterling –Wired – Beyond the Beyond
- ^Baltodano, S. (2013). RISE.http:// mme.fiu.edu/wp-content/uploads/2013/12/F13-OR-T-4.pdf