Caulk

For the studs installed on horseshoes, seeCaulkin.

Silicone-based caulk on this upturned bathroom sink will spread smoothly, sealing the gap, when the sink is turned over and installed.

Caulkorcaulkingis a material used tosealjointsor seams against leakage in various structures and piping.

The oldest form of caulk consisted of fibrous materials driven into the wedge-shaped seams between boards onwooden boats or ships.Cast ironseweragepipeswere formerly caulked in a similar way. Riveted seams inshipsandboilerswere formerly sealed by hammering themetal.

Modern caulking compounds are flexible sealing compounds used to close up gaps inbuildingsand other structures againstwater,air,dust,insects,or as a component infirestopping.In thetunnelingindustry, caulking is the sealing of joints in segmentalprecast concretetunnels, commonly by usingconcrete.

Historical uses

Wooden shipbuilding

Traditional caulking (also spelled calking) on wooden vessels usesfibersofcottonandoakum(hemp) soaked in pinetar.These fibers are driven into the wedge-shaped seam between planks, with a caulking mallet and a broadchisel-like tool called a caulking iron. The caulking is then covered over with aputty,in the case of hull seams, or else in deck seams with melted pinepitch,in a process referred to as paying, or "calefaction".Those who carried out this work were known as caulkers. In theHebrew Bible,theprophetEzekielrefers to the caulking of ships as a specialist skill.

• 
  Dried-out caulking on theSevern trowSpry,now displayed on shore
• 
  The tools of traditional wooden ship caulking: caulking mallet, caulker's seat, caulking irons,cottonandoakum
• 
  A caulking mallet, tar pot and a piece of petrified tar found on board the 16th centurycarrackMary Rose

Iron or steel shipbuilding

In riveted steel or ironship construction,caulking was a process of rendering seams watertight by driving a thick, blunt chisel-like tool into the plating adjacent to the seam. This had the effect of displacing the metal into a close fit with the adjoining piece.

Boilermaking

Caulking of iron and steel, of the same type described above for ship's hulls, was also used byboilermakersin the era of rivetedboilersto make the joints watertight and steamtight.

Modern use in construction

Application

Man applying caulk tobaseboard

For bulk use, caulk is generally distributed in disposable cartridges, which are rigid cylindrical cardboard or plastic tubes with an applicator tip at one end, and a movable plunger at the far end. These are used in caulking guns, which typically have a trigger connected to a rod which pushes the plunger, and has aratchetto prevent backlash. The push rod may also be actuated by a motor or by compressed air. Similar mechanisms are used forgrease guns.

For smaller applications, caulk may be distributed insqueeze tubes.

Backer rod

Backer rod, also called backer material or back-up rod, is a flexiblefoamproduct used behind caulking to increase elasticity, reduce consumption, force the caulking into contact with the sides of the joint creating a better bond, determine the thickness of the caulking, and define the cross-section hour-glass shape of the caulk. The backer rod also acts as a bond breaker to keep the caulking from sticking to the bottom of the opening—called a three-sided bond—with the caulk only adhering to the sides of the opening in an hour-glass shape it can flex more easily and is less likely to tear. Backer rods can also be used to reduce consumption of the caulking by filling part of the joints.

Closed-cell foam does not absorb water and is impermeable. Closed-cell rods are less compressible and should not be compressed more than 25%.Closed-cell rod will also lose firmness and out-gas if damaged during installation or overcompressed or at sharp bends. The gasses cannot pass through this backer rod and can deform, weaken, and even cause holes (leaks) in the caulk orsealantas it escapes.

Out-gassing is the reason that open-cell backer rod was developed.Open-cell foam is porous so it will let gasses through which could otherwise cause blistering of the caulk or sealant. Additionally, open-cell backer rod allows air to get to the back side of the caulk or sealant which accelerates curing when used with air-cured sealants such assilicone.Open-cell rod is more compressible than closed-cell foam and should be compressed 25% to 75%.

Energy efficiency

According to theConsumer Federation of America,sealing unwanted leaks around homes is an excellent way to cut home energy costs and decrease the householdcarbon footprint.

Also, sealing cracks and crevices around homes lessens the strain on home appliances and can save time, money and hassle by preventing major repairs.

Preventing infestation

Sealing cracks and crevices prevents ingress by rodents.

Types

Acrylic latex

The most common type of caulk is acrylic latex, for general-purpose use.Not only is acrylic latex inexpensive, but it is also the easiest type to apply smoothly and later paint if needed.

Acrylic tile sealant

Acrylic tile sealant usually comes in small tubes and is commonly used for wet applications.

Polyurethane

Polyurethanecaulk is very durable and professional grade.

Silicone

Main article:Sealant

Silicone caulking extruded from a caulking gun

Silicone caulk or sealant is water-, mold-, and mildew-resistant.Technically, when a joint material is silicone-based, it is considered asealantrather than caulk.

External links

• Media related toCaulkingat Wikimedia Commons
• The dictionary definition ofcaulkat Wiktionary