CFLAGS += -DRBOOT_GPIO_ENABLED=0

CFLAGS += -DPLATFORM_ESP8266

#

# LuaOS configuration

#

CFLAGS += -DCPU_HZ=80000000L # CPU frequency in hertz

CFLAGS += -DCORE_TIMER_HZ=CPU_HZ # CPU core timer frequency

CFLAGS += -D_CLOCKS_PER_SEC_=100 # Number of interrupt ticks for reach 1 second

CFLAGS += -DUSE_NETWORKING=0 # Networking is used (1 = yes, 0 = not)

CFLAGS += -DMTX_USE_EVENTS=0 # Use event groups in mtx implementation (experimental)

CFLAGS += -DluaTaskStack=192*5 # Stck size assigned to lua thread

CFLAGS += -DtskDEF_PRIORITY=0 # Default task priority

CFLAGS += -DdefaultThreadStack=192*5

#

# File system configuration

#

CFLAGS += -DUSE_CFI=1 # Enable CFI (common flash interface)

CFLAGS += -DSPIFFS_ERASE_SIZE=4096 # SPI FLASH sector size (see your flah's datasheet)

CFLAGS += -DSPIFFS_LOG_PAGE_SIZE=256 # SPI FLASH page size (see your flah's datasheet)

CFLAGS += -DSPIFFS_LOG_BLOCK_SIZE=8192 # Logical block size, must be a miltiple of the page size

CFLAGS += -DSPIFFS_BASE_ADDR=0x100000 # SPI FLASH start adress for SPIFFS

CFLAGS += -DSPIFFS_SIZE=0x80000 # SPIFFS size

SPIFFS_ESPTOOL_ARGS = 0x100000 $(BUILD_DIR)spiffs_image.img

#

# Console configuration

#

CFLAGS += -DUSE_CONSOLE=1 # Enable console

CFLAGS += -DCONSOLE_BR=115200 # Console baud rate

CFLAGS += -DCONSOLE_UART=1 # Console UART unit

CFLAGS += -DCONSOLE_SWAP_UART=2 # Console alternative UART unit (0 = don't use alternative UART)

CFLAGS += -DCONSOLE_BUFFER_LEN=255 # Console buffer length in bytes

#

# LoraWAN driver connfiguration for RN2483

#

CFLAGS += -DLORA_UART=3 # RN2483 UART unit

CFLAGS += -DLORA_UART_BR=57600 # RN2483 UART speed

CFLAGS += -DLORA_UART_BUFF_SIZE=255 # Buffer size for RX

CFLAGS += -DLORA_RST_PIN=14 # RN2483 hardware reset pin

#

# Lua configuration

#

CFLAGS += -DDEBUG_FREE_MEM=1 # Enable LUA free mem debug utility (only for debug purposes)

CFLAGS += -DLUA_USE_LUA_LOCK=0 # Enable if Lua must use real lua_lock / lua_unlock implementation

CFLAGS += -DLUA_USE_SAFE_SIGNAL=1 # Enable use of LuaOS safe signal (experimental)

CFLAGS += -DSTRCACHE_N=1

CFLAGS += -DSTRCACHE_M=1

CFLAGS += -DMINSTRTABSIZE=32

#

# Standard Lua modules to include

#

CFLAGS += -DLUA_USE__G=1 # base

CFLAGS += -DLUA_USE_OS=1 # os

CFLAGS += -DLUA_USE_MATH=1 # math

CFLAGS += -DLUA_USE_TABLE=1 # table

CFLAGS += -DLUA_USE_IO=1 # io

CFLAGS += -DLUA_USE_STRING=1 # string

CFLAGS += -DLUA_USE_COROUTINE=1 # coroutine

CFLAGS += -DLUA_USE_DEBUG=1 # debug

#

# LuaOS Lua modules to include

#

CFLAGS += -DLUA_USE_TMR=1 # timer

CFLAGS += -DLUA_USE_PIO=1 # gpio

CFLAGS += -DLUA_USE_LORA=1 # lora

CFLAGS += -DLUA_USE_PACK=1 # pack

CFLAGS += -DLUA_USE_THREAD=1 # thread

CFLAGS += -DLUA_USE_EDITOR=0 # editor